FULL ONE YEAR WARRANTY ON CRAFTSMAN RADIAL SAW
If within one year from the date of purchase, this Craftsman Radial Saw fails due to a defect in material or
workmanship, Sears will repair it, free of charge.
WARRANTY SERVICE IS AVAILABLE BY SIMPLY CONTACTING THE NEAREST SEARS STORE
OR SERVICE CENTER THROUGHOUT THE UNITED STATES.
This warranty gives you specific legal rights, and you may have other rights which vary from state to state.
SEARS, ROEBUCK AND CO., Sears Tower, BSC 41 3, Chicago, IL 60684
general safety instructions
1. KNOW YOUR POWER TOOL
Read and understand the owner's manual arrd labels
affixed to the tool. Learn its applications and limitations
as well as the specific potential hazards peculiar- to this tool.
2. GROUND ALL TOOLS
This tool Is equipped with :rn approved 3 conductor
cord and a
3. KEEP GUARDS IN PLACE
in worMug order, and in proper adjustment and atigrlment.
4. REMOVE ADJUSTING KEYS AND WRENCHES
Form habit of checking to see that keys and adjusting
wrenches _re removed from tool before tLJrnH]g it on
5. KEEP WORK AREA CLEAN
Cluttered teas and benches nvite accidents Floor
must not bp slippery due to wax or sawdust,
6. AVOID DANGEROUS ENVIRONMENT
Don't use power tools in damp or wet locations or expose them to rain. Keep work area well bighted.
Provide adequate surrounding work space.
7. KEEP CHILDREN AWAY
All visttor,, should be kept a safe distance from work
area
8. MAKE WORKSHOP KIDPROOF
with p_tdlocks, master switches, or by ,emoving starter key_
9. DON'T FORCE TOOL
It will do rhe job bette_ and safer at the rate for which _t was designed.
10. USE RIGHT TOOL
Don't forc_ tool or attacfrment to do a job it was not designed for.
11. WEAR PROPER APPAREL
Do not wea_ loose clothing, gloves, neckties or jewelry (rings, wrist watches} to get caught in moving parts.
Nonslip footwear is recommended. Wear protective
hair covering to contain long hair. Roll long sleeves above the t Ibow.
12. USE SAFETY GOGGLES (Head Protection)
Wear Safety goggles (must comply with ANSI Z87.1)
at all times. Everyday eyeglasses only have impact resistant lenses, they are NOT safety glasses. Also, use face or dust mask if cutting operation is dusty, and ear
for power tools
protectors (plugs or muffs) during extended periods of operation.
13. SECUREWORK
Use clamps or a vise to hold work when practical. It's
safer than qsing 'your hand, frees both hands to operate tool.
14.DON'T OVERREACH
Keep proper fooUng and balance at all times.
15, MAINTAIN TOOLS WITH CARE
Keep tools sharp and clean for best and safest
performance Follow *nstructions for lubricating and changirrg accesso, ies
16. DISCONNECT TOOLS
belgie setvcing;when changing accessories such as blades, bits. cutters, etc.
17. AVOID ACCIDENTAL STARTING
Make sure switch is in "OFF" position bqfore plugging
in,
18. USE RECOMMENDED ACCESSORIES
Consult the owner's manual for recommended
accessories, Follow the instructions that accompany the accessories. The use of improper accessories may cause hazards.
19. NEVER STAND ON TOOL
Serious injury could occur if the toot is tipped or if the
cutting toot is accidentally contacted.
Do not store materials above or near the tool such that it is necessary to starrd on the toot to reach them.
20. CHECK DAMAGED PARTS
Before further use of the tool, a guard or other part that is damaged should be carefully checked to ensure that it will operate properly and perform its intended function.
Check for alignment of moving parts, binding of moving
parts, breakage of parts, mounting, and any other
conditions that may affect its operation. A guard or other part [hat is damaged should be properly repaired or replaced
21. DIRECTION OF FEED
Feed work into a blade or cutter against the direction of rotation of the blade or cutter only.
22.NEVER LEAVE TOOL RUNNING UNATTENDED
Turn power off Don't leave tool until it comes to a complete stop.
