Timer recording | Sharp MD-M3H specification

(Continued)

●Before setting the timer, make sure that the clock setting is correct. (Page 9)

■Timer recording

Before timer recording, the following preparations are required.

●Load a CD, a recordable MD.

●Preset the radio station.

(Remote control operation)

3

4,5,6,7,8

5,6,7,8

	2
1,10	9

1 Press the ON/STAND-BY button to turn the power on.

2 Press the CD, TUNER(BAND), AUX button to select desired function.

3 Press the TIMER button to select the timer recording mode.

4 During “f REC” is flashing, press the ENTER button.

REC	REC

DISC TOC
TRACK
MEMORY
RANDOM	REC
TOTAL	REC
REMAIN	SLEEP

5 Within 5 seconds, press the or button to set the hour to start, and then press the ENTER button.

REC

REC

6 Press the or button to set the minute to start, and then press the ENTER button.

REC

REC

●If not set manually, the ending time will automati- cally be set for one hour after the starting time.

7 Press the or button to set the hour to stop, then press the ENTER button.

	REC
DISC TOC
TRACK
MEMORY
RANDOM	REC
TOTAL	REC
REMAIN	SLEEP

	REC
DISC TOC
TRACK
MEMORY
RANDOM	REC
TOTAL	REC
REMAIN	SLEEP

8 Press the or button to set the minute to stop, then press the ENTER button.

	REC
DISC TOC
TRACK
MEMORY
RANDOM	REC
TOTAL	REC
REMAIN	SLEEP

REC REC

9 Rotate the VOLUME control to adjust the sound volume.

●Be careful not to turn the volume up too high.

10 Press the ON/STAND-BY button to enter the stand-by mode.

●The timer set indicator will light up.

11 When the timer start time is reached, timer recording will start.

12 When the timer end time is reached, timer recording will stop.

●“f REC” will disappear, and the timer mode will be cancelled.

The unit will enter the stand-by mode.

Notes:

●The timer cannot control the component con- nected to the Auxiliary Input sockets.

●When the available recording time has been con- sumed, the recording will stop.

To change the programmed contents:

Start again from step 1.

To confirm the timer setting:

Press the TIMER button once.

●The turn-on time, the turn-off time and name of sound source will be displayed.

To cancel timer operation:

1Whilst in the timer stand-by mode, press the ON/ STAND-BY button to turn the power on.

2Press the ON/STAND-BY button repeatedly to turn off the timer, “f REC” will go out.

40

Image 42

Sharp MD-M3H operation manual Timer recording

Contents

Contents MD-M3H Terms of Guarantee A9903.YT Service Information Special Notes Volume control AccessoriesPrecautions General Names of Controls and Indicators Front panelRear panel 16 17 18 19 20 21 Display windowSpeaker section Remote control MD/CD Section Preparation for USE Aerial connectionSpeaker connection Speaker cushion Removing the speaker grilles Connecting the AC power leadDemo mode Placing the system Play Remote controlPrecautions for battery use To change the brightness of the dis To see the time display Setting the ClockTo change the time display mode To change the clock time Extra bass X-BASS VolumeSound Control Pre-programmed equalizer Surround To interrupt playback Compact Disc OperationCD playback To stop playback Minidisc Operation MD playbackTo remove a MiniDisc Repeat and random play Convenient CD and MD OperationApss Auto Program Search Sys- tem Cue and review To clear the programmed selections To cancel the ApmsApms Automatic Programmable Music Selector To check which tracks are programmed Switching the time display Changing the display during MD playbackTime Auto tuning TuningManual tuning Press the ON/STAND-BY button to enter the stand- by mode Preset tuning Preset memory scan Display Mode Information provided by RDSPTY Test Alarm None To erase all of the contents of preset memory Aspm Auto Station Program MemoryTo stop the Aspm operation before it is complete To cancel the station select operation Page If you have selected the traffic programme To switch the display Presetx WTo manually recall the stations stored in memory About the Ptyi Dynamic PTY Indicator Checking the stand-by mode settingTo cancel the EON stand-by mode Meaning When in the EON stand-by mode, press the EON button EON-TI About the TP and TA indicators TP indicator TA indicator Meaning Recording Differences from tape recordingsDisc writing TOC About track numbers To check the remaining time available for recording To cancel the operationRecording from a CD onto a MiniDisc One-Touch Editing To stop recording To record without using One-Touch Editing Apms recordingCD0MD Edit High /NORMAL Recording from the built-in radio onto a MiniDisc To record the track number whilst record- ingRecording is performed as a single track Editing What the editing function can doType of characters used Within 10 seconds, press the Enter button To create a disc nameTo erase a disc name Press the Enter button to enter the character To create a track name To erase a track name Name TOC Edit Enter Clear To change disc names and track namesTo add a character Example To change Besut to Best When both tracks have a name DivideCombine Move To combine two non-contiguous tracksExample To erase tracks one at a time EraseAll Erase To erase all of the tracks at once Timer Operation Timer playback Timer recording To use sleep and timer playback in combi- nation Simultaneous sleep and timer op- erationTo cancel the sleep operation To use sleep and timer recording in com- bination Using External Units Connecting external unitsHeadphones Listening to sound from an exter- nal unit Manual recording What is a MINIDISC? Symptom Possible cause Remedy TroubleshootingIf a problem occurs Mini Disc System Limitations MD recording and playback Symptom Possible causeCD Playback Radio reception Error Messages When an error message is displayed, proceed as follows Resetting the Microcom Maintenance Puter External careCare of compact discs Specifications Memo