Manuals / Sharp / Computer Equipment / Projector

Sharp XG-SV100W Removing and Installing the Lamp Unit, Disconnect the power cord, Info, Appendix

Models: XG-SV100W XG-SV200X

1 92

Download 92 pages 27.45 Kb

Page 77

Image 77

Removing and Installing the Lamp Unit

Warning!

•Do not remove the lamp unit from the projector right after use. The lamp and parts around the lamp will be very hot and may cause burns or injury.

Optional

accessory

Lamp unit

AN-SV10LP

Info

•Do not touch the glass surface of the lamp unit or the inside of the projector.

•To avoid injury to yourself and damage to the lamp, make sure you carefully follow the steps below.

•Do not loosen other screws except for the lamp unit cover and lamp unit.

1 Press STANDBY/ON on the projector or STANDBY on the remote control to put the projector into Standby mode.

2 Disconnect the power cord.

•Unplug the power cord from the AC socket.

•Leave the lamp until it has fully cooled down (about 1 hour).

3Remove the lamp unit cover.

•Loosen the user service screw (1) that

secures the lamp unit cover. Remove the lamp unit cover (2).

STANDBY/ON button

AC socket

User service screw (for lamp unit cover)

Appendix

Page 77

Image 77

Sharp XG-SV100W appendix Removing and Installing the Lamp Unit, Disconnect the power cord, Remove the lamp unit cover, Info

Contents

Setup FeaturesMODEL IntroductionModel No Serial No DANGER SPECIAL NOTE FOR USERS IN THE U.KThe supplied CD-ROM contains operation instructions in English, German, French, Spanish, Italian, Dutch, Swedish, Portuguese, Chinese, Korean and Arabic. Carefully read through the operation instructions before operating the projector 2. CONSUMER PRODUCT SAFETY ACT 1. WARRANTYSee bottom of projector IntroductionENGLISHPRODUCT DISPOSAL Caution Concerning Lamp ReplacementINFORMATION Troubleshooting MaintenanceInfo .........Indicates safeguards for using the projector Using the Menu ScreenUsing SetupUseful Features PreparingIntroduction ReferenceAppendix 11. Power Sources 5. Cleaning8. Accessories 13. Power-Cord Protection19. Replacement Parts 18. Damage Requiring Service20. Safety Check 15. OverloadingCaution concerning the setup of the projector Observe the following safeguards when setting up your projectorCaution concerning the lamp unit Rest your eyes occasionallyInfo Using the projector in other countriesCaution regarding usage of the projector Other connected equipmentAccessing the PDF Manuals How to Access the PDF Operation ManualsSETUP MANUAL Supplied accessories AccessoriesOptional accessories Introduction17 18 Part Names and FunctionsSide View Top ViewIntroduction Using the Kensington LockRear View Terminals Part Names and Functions Continued Usable Range Inserting the Batteries2 Insert the batteries IntroductionEasy Start Setup and Projection1. Place the projector facing a wall or a screen 3. Turn the projector on5. Adjust the focus and the zoom 4. Adjust the angle8. Turn the power off 6. Correcting the image distortion due to the projection angleVideo Setup Setting Up the ProjectorSetting Up the Projector Standard Setup Front ProjectionScreen Size and Projection Distance For XG-SV200X 43 Signal Input Normal Mode169 Signal Input 169 Mode 43 Signal Input Normal Mode Setting Up the Projector ContinuedFor XG-SV100W 1610 Signal Input Normal Mode Projection PRJ Mode a Ceiling-Mount SetupSetup Terminals on the Projector Connecting the Projector to Other EquipmentS-video output ConnectionsConnecting the Projector to Other Equipment Continued Controlling the Projector by a Computer When connecting to a computer using an RS-232C serial control cableInfo ConnectionsControlling the Projector by a Computer Continued Connecting the Power CordWhen connecting to the LAN terminal using a LAN cable Turning the Projector On/Off Press STANDBY/ON on the projector or ON on the remote controlTurning the Projector On Basic OperationImage Projection Adjustable rangeShifting the Lens Adjustable range1 Press H&V SHIFT on the remote control Using the Adjustment Feetprojector or the remote control to adjust the image position 1 Rotate the adjustment feet to adjust the projected angleAdjusting the Projected Image Size Adjusting the FocusPress FOCUS +/- on the remote control to adjust the focus Image Projection ContinuedCorrecting Trapezoidal Distortion Press KEYSTONE on the projector or on the remote controlThere are the two types of the Keystone Correction Selecting the Type of the CorrectionImage Projection Continued GEOMETRIC ADJUSTMENT3 Press ENTER to set the position 1 Press KEYSTONE on the H&V KEYSTONEprojector or on the remote control repeatedly until “H&VSelect the appropriate input mode for the connected equipment Switching the Input ModeWhen you select the input mode with INPUT R/P on the projector Image Projection ContinuedDisplaying the Black Screen and Turning Off the Sound Temporarily Adjusting the VolumeOn-screen display Basic OperationPress RESIZE Resize ModeFor XG-SV200X COMPUTERBasic Operation VIDEO/DTVFor XG-SV200X Cutout area on which images cannot be projectedCOMPUTER For XG-SV100WImage Projection Continued Basic Operation About CopyrightsFor XG-SV100W VIDEO/DTVDisplaying and Setting the Break Timer Operating with the Remote ControlUsing the Spot Function Switching the Eco+Quiet ModePress AUTO SYNC to manually adjust with Auto Sync function Auto Sync Adjustment1 Press MAGNIFY on the remote control 2 Press RETURN on the remote control to cancel the operationUsing the Remote Control as the Wireless Computer Mouse Operating with the Remote Control ContinuedConnecting with a USB cable When moving the cursorThe following shows the items that can be set in the projector Menu Items“Picture” menu “Audio” menuMenu Items Continued “Signal adjustment SIG” menu“Screen adjustment SCR” menu “Network Net.” menu “Projector adjustment PRJ” menuFeatures UsefulMenu Selections Adjustments Using the Menu Screen2 Press Q or O and select “Picture” to adjust 1 Press MENU3 Press P or R and select “Bright” to adjust To adjust the projected image while watching it4 Press O or Q to adjust the item selected Press ENTER2 Adjusting the Image Picture Adjustment “Picture” Menu1Selecting the Picture Mode Info4 Adjusting the Colors Adjusting the Color Temperature3 Set or adjust each item in the C.M.S. color adjustment screen Picture Adjustment “Picture” Menu ContinuedC.M.S. color adjustment screen 5 Reducing Image Noise DNR1 Speaker Setting Audio Adjustment “Audio” Menu3 Audio Output Type Setting 4 Adjusting the Audio3 Auto Sync Adjustment Signal Adjustment “SIG” Menu4 Signal Type Setting 2 Resolution Setting6 Setting the Video Setup 5 Setting the Video System8 Checking the Input Signal 7 Selecting the Dynamic Range1 Setting the Resize Mode Screen Adjustment “SCR” Menu3 Setting the Overscan 4Setting the On-screen Display5 Closed Caption The projector can switch the on-screen6Selecting a Startup and Background Image 7Reversing/Inverting Projected Images2 Auto Restart Function 1 Auto Power Off Function3COMPUTER2 Select 4STANDBY Modea Setting/Changing the keycode 6Fan Mode Setting7System Lock Function 1 Select “System Lock”, then press ENTER or QKeylock Function Helpful Functions Set during Installation “PRJ” menu Continued8 DLP LinkTM 9 DLP LinkTM Invert0Memory Menu Rotate Indicatora Load Memory a Save MemoryChecking the Lamp Life Status Returning to the Default SettingsHelpful Functions Set during Installation “PRJ” menu Continued “SIG” menu Resolution “SCR” menu Language1 Setting a Password Setting Up the Projector Network Environment “Net.” Menua Setting a Password a Changing the Password2 DHCP Client Setting Setting Up the Projector Network Environment “Net.” Menu Continued3 TCP/IP Setting 4 Returning to Default Settings NetworkUseful 6 Conﬁrming the Projector InformationFeatures Viewing Stereoscopic 3D Images Precautions on Viewing Stereoscopic 3D ImagesIF YOU OR ANY MEMBER OF YOUR FAMILY HAS A HISTORY OF EPILEPSY EpilepsyFeatures UsefulInformation on the 3D Projection Function Viewing Stereoscopic 3D Images Continued3 Switch the Input mode of the Using 3D Viewing Modeprojector to enable input of 3D video signals equipment and play back the 3D contentViewing Stereoscopic 3D Images Continued AppendixCleaning the projector MaintenanceCleaning the lens or lens cover Cleaning the exhaust and intake ventsAbout the lamp indicator Maintenance IndicatorsAbout the temperature warning indicator Appendix If the power is turned off for a brief moment due to power outage or some other cause while using the projector, and the power supply recovers immediately after that, the lamp indicator will illuminate in red and the lamp may not be lit. In this case, unplug the power cord from the AC outlet, replace the power cord in the AC outlet and then turn the power on againInfo Lamp Regarding the LampCaution Concerning the Lamp Replacing the Lamp2 Disconnect the power cord Removing and Installing the Lamp UnitOptional accessory 3 Remove the lamp unit cover1 Connect the power cord Resetting the Lamp Timer2 Reset the lamp timer Regarding the Lamp ContinuedAppendix Compatibility ChartComputer 3D Supported Signals Compatibility Chart ContinuedAppendix Attaching the Ceiling-mount Rotating Module AN-SV100TFirst, lightly screw all four bolts and then tighten them ﬁrmly 2 Fasten the terminal covers at the Attaching the Terminal Cover to the Moduletwo points with the supplied screws2 Attach the height-adjustment pole to the ceiling mount When installed with the AN-TK201Attaching the Ceiling Mount to the Ceiling 1 Attach the ceiling mount to the ceiling1 Attach the ceiling mount to the ceiling When installed with the AN-TK202Attaching the Ceiling Mount to the Ceiling Continued Appendix Troubleshooting22-26 22-2669, 70 Troubleshooting Continued70, 73 22-26Ghosting a double image Appendix3D images ﬂ icker when For SHARP Assistance Dimensions main body only W × H × D SpeciﬁcationsAppendix S-Video mini DIN 4 pinUnits inches mm DimensionsAppendix Index