Assembly (continued)

Assembling tube sections (cont.)

2.Slip off the protective covers from the ends of both tubes, and loosen the cou- pler screw knob.

3.Insert the tool assembly into the cou- pler, with the tool decal facing up, until the line of the decal is flush with the end of the coupler.

4.Twist the tool assembly back and forth until you are sure it snaps in place by the coupler latch.

5.When the two tube halves are locked together, press down on the spring- loaded latch protector and tighten the coupler screw knob.

Disassembling the tube sections

1.With the pole pruner on a clean, flat surface, loosen the coupler screw. The spring-loaded coupler protector should pop up.

2.Press down on the latch with your finger or thumb. This releases the coupler lock.

3.Pull the upper tube assembly out of the coupler.

Coupler

Latch Protector (lowered)

Coupler Screw Knob

Press latch

Installing and Adjusting the Bar and Chain

Installing the Chain

WARNING!

Never attempt to install, replace, or adjust the chain with the engine running.

WARNING!

The saw chain is very sharp. Wear gloves to protect your hands when handling.

NOTE:

For longest chain life, let new or replacement chain loops soak in oil overnight before installation.

1.Using the small end of the plug wrench, remove the sprocket cover nut (turn counter-clockwise to remove) and remove the sprocket cover.

Sprocket Cover

Sprocket Cover

 

 

Nut

 

 

CAUTION!

Failure to align the guide bar and chain tensioning pin can cause seri- ous damage to the sprocket cover, guide bar, chain tensioning pin and cutting head assembly.

2.Place the guide bar over the guide bar adjustment stud on the cutting head assembly. Align the chain tensioning pin with the hole in the guide bar.

Guide Bar

Adjustment

Stud

Chain

Tensioning

Screw

Chain Tensioning Pin

Guide Bar

Adjustment Stud

Guide Bar

Chain Tensioner

Hole

 

3.Install the chain loop over the drive links within the guide bar groove, and then align the chain over the drive sprocket. Verify that the cutters are properly oriented as shown. If chain installation is difficult or if the chain appears too tight, refer to the section “Adjusting the Chain” on the next page.

WARNING!

Never operate the pole pruner without the sprocket cover installed.

4.Install the sprocket cover over the bar stud. Using finger-pressure only, install the sprocket cover nut.

5.Refer to the next page for chain adjust- ing procedures.

Top of bar

Bar tip

Bottom of bar

Page 8 Page 10
Page 9
Image 9
Shindaiwa 62891-94311 Installing and Adjusting the Bar and Chain, Disassembling the tube sections, Installing the Chain
Page 8 Page 10

62891-94311 specifications

The Shindaiwa 62891-94311 is a premium combination of engineering and technology, designed for lawn care and landscaping professionals. This tool provides efficient and reliable performance, making it a top choice for outdoor enthusiasts and contractors alike. One of the standout features of the Shindaiwa 62891-94311 is its lightweight yet durable construction. This ensures that it delivers high performance without sacrificing user comfort, allowing operators to work for extended periods without undue fatigue.

This model is equipped with advanced engine technology that enhances fuel efficiency and reduces emissions. The 2-stroke engine not only delivers impressive power but also adheres to stringent environmental regulations. Users appreciate the reduced environmental footprint, which aligns with a growing trend towards sustainability in landscaping equipment.

Another key characteristic of the Shindaiwa 62891-94311 is its ergonomic design. The handle is designed for optimum comfort and control, reducing vibration during use, which leads to greater precision and reduces the risk of strain injuries. The combination of the lightweight structure and ergonomic grip allows for longer operational hours, ensuring that users can tackle large projects efficiently.

The product features easy-start technology, enabling quick and effortless ignition. This is particularly beneficial for professionals who need to maximize productivity on job sites. Additionally, the model includes an adjustable throttle, allowing users to easily adapt the power output according to their specific needs, whether it’s for trimming, edging, or heavy-duty cutting tasks.

Durability is another focus for the Shindaiwa 62891-94311. The materials used in its construction are engineered to withstand the rigors of outdoor use, ensuring longevity and reliability. This means that users can invest in this tool with confidence, knowing it can handle extensive workloads and still perform optimally.

In conclusion, the Shindaiwa 62891-94311 is a versatile and powerful tool that incorporates advanced technology, ergonomic design, and durability. It is an ideal choice for landscaping professionals seeking a reliable, efficient, and eco-friendly solution for their outdoor tasks. Whether trimming hedges or tackling tough underbrush, this model stands out as a preferred option in the field of outdoor power equipment.
Top Page Image Contents