Siemens 410 5.3 Parameter List (short form)

Issue A1 5 System Parameters

MICROMASTER 410 Operating Instructions

6SE6400-5EA00-0BP0 51

5.3 Parameter List (short form)

Explanatory information on following table:

Ø Default: Factory setting

Ø Level: Access level (Acc)

Ø DS Inverter status (Drive State), indicates the inverter state in which a

parameter can be modified (see P0010).

♦ C Commissioning

♦ URun

♦ T Ready to run

Ø QC Quick Commissioning

♦ Q Parameter can be modified in the Quick Commissioning state.

♦ N Parameter cannot be modified in the Quick Commissioning state.

Always

ParNr ParText Default Acc DS QC

r0000 Drive display - 1 - -

P0003 User access level 1 1 CUT N

P0004 Parameter filter 0 3 CUT N

P0010 Commissioning parameter filter 0 1 CT N

Quick Commissioning

ParNr ParText Default Acc DS QC

P0100 Europe / North America 0 1 C Q

P0101 Hidden Switch Setting 0 1 C Q

P3900 End of quick commissioning 0 1 C Q

Parameter Reset

ParNr ParText Default Acc DS QC

P0970 Factory reset 0 1 C N

Inverter Unit (P0004 = 2)

ParNr ParText Default Acc DS QC

r0018 Firmware version - 3 - -

r0026 CO: Act. DC-link voltage - 2 - -

r0206 Rated inverter power [kW] / [hp] - 3 - -

r0207 Rated inverter current - 3 - -

r0209 Maximum inverter current - 3 - -

P0210 Supply voltage 230 3 CT N

P0290 Inverter overload reaction 2 3 CT N

P1800 Pulse frequency 4 3 CUT N

Contents

Main MICROMASTER 410 Documentation Page 4 Foreword Definitions and Warnings Use for intended purpose only Safety Instructions General Transport & Storage Commissioning Operation Repair Dismantling & Disposal Page Table of Contents Page Issue A1 Table of Contents List of Illustrations List of Tables Page 1 Overview 1.1 The MICROMASTER 410 1.2 Features Main Characteristics Performance Characteristics Protection Characteristics 2 Installation 2.1 General Installation after a Period of Storage 2.2 Power Losses 2.3 Ambient operating conditions Temperature Humidity Range Altitude Page Issue A1 2 Installation 2.4 Harmonic Currents Harmonic currents with 1% mains impedance. 2.5 Derating with Pulse Frequencies 2.6 Overvoltage and Trip Levels 2.7 Mechanical Installation Issue A1 2 Installation 30 mm 100 mm 100 mm 30 mm Figure 2-5 Clearance distances for mounting the inverter 2.7.1 Mounting Brackets 2.7.2 DIN Rail Mounting 2.8 Electrical Installation 2.8.1 General Operation with ungrounded (IT) supplies Operation with Residual Current Device Operation with long cables 2.8.2 Power and motor connections Removal of Y Capacitor Link Access to the power and motor terminals 2.8.3 Avoiding Electro-Magnetic Interference (EMI) Action to Take Page 3 Commissioning Page 3.2 Commission Modes Front Panels for the MICROMASTER 410 3.2.1 Commissioning without an Operator Panel Warnings and faults states on the Inverter 3.2.2 Basic operation 3.2.3 Changing the Line Supply Frequency Cutting the supply link Using the Operator Panel 3.2.4 Commissioning Overview with the optional Operator Panel Prerequisites 3.2.4.1 Commissioning with the Operator Panel Buttons on the Operator Panel Changing parameters with the Operator Panel Changing single digits in Parameter values 3.2.4.2 Quick commissioning (P0010=1) 3 Commissioning Issue A1 40 Flow chart Quick Commissioning (Level 1 Only) Motor data for parameterization 3.2.4.3 Reset to Factory default 3.3 General operation Basic operation with the OP External motor thermal overload protection Page 4 Using the MICROMASTER 410 4.1 Frequency Setpoint (P1000) 4.2 Command Sources (P0700) Starting the motor Stopping the motor Reversing the motor 4.3 OFF and braking Functions 4.3.2 OFF2 4.3.3 OFF3 4.3.4 DC braking 4.3.5 Compound Braking 4.4 Control Modes (P1300) 4.5 Faults and Alarms Standard Inverter Operator Panel Fitted 5 System Parameters 5.1 Introduction to MICROMASTER System Parameters 5.1.1 Access Levels MICROMASTER 410 Operating Instructions 5.2 Parameter Overview , Figure 5-1 Parameter Overview s e c 5.3 Parameter List (short form) Always Quick Commissioning Parameter Reset Inverter Unit (P0004 = 2) Motor Data (P0004 = 3) Commands and Digital I/O (P0004 = 7) Issue A1 5 System Parameters Analogue I/O (P0004 = 8) Setpoint Channel and Ramp Generator (P0004 = 10) Drive Features (P0004 = 12) Motor Control (P0004 = 13) Issue A1 5 System Parameters Communication (P0004 = 20) Alarms, Faults and Monitoring (P0004 = 21) Page 6 Troubleshooting 6.1 Troubleshooting with the Standard Inverter LED 6.2 Troubleshooting with the Operator Panel (OP) 6 Troubleshooting Issue A1 58 6.3 Fault messages Fault Possible Causes Diagnose & Remedy Reac- Issue A1 6 Troubleshooting Fault Possible Causes Diagnose & Remedy Reac- 6 Troubleshooting Issue A1 60 6.4 Alarms Alarm Possible Causes Diagnose & Remedy Reac- Issue A1 6 Troubleshooting Alarm Possible Causes Diagnose & Remedy Reac- Page Issue A1 7 MICROMASTER 410 Specifications 7 MICROMASTER 410 Specifications Table 7-1 MICROMASTER 410 Performance Ratings Feature Specification 7 MICROMASTER 410 Specifications Issue A1 64 Table 7-2 Terminal Torques Field Wiring Connectors Table 7-3 MICROMASTER 410 Specifications Input voltage range 1 AC 200 V 240 V, 10 % (with built in Class B Filter) Issue A1 7 MICROMASTER 410 Specifications Input voltage range 1 AC 200 V 240 V, 10 % (Unfiltered) Input voltage range 1 AC 100 V 120 V, 10 % (Unfiltered) Page 8 Options 8.1 Variant Independent Options 8.2 Variant Dependent Options Page 9 Electro-Magnetic Compatibility (EMC) 9.1 Electro-Magnetic Compatibility (EMC) 9.1.1 Self-Certification 9.1.2 Technical Construction File 9.1.3 EMC Directive Compliance with Harmonics Regulations 9.1.4 General cases of EMC performance Case 1: General Industrial Case 2: Filtered Industrial Case 3: Filtered - for residential, commercial and light industry Page B Applicable Standards C List of Abbreviations Index Page Page Page Page View of Unit