transducer is used) must now be set. This value is listed on the transducer model plate. Press the “CONTINUE SLIDE CAL.” softkey to continue the calibration process or “EXIT” to return to slide configuration.

f)Finally, the “Calibration Point” must be set. The slide should be taken to bottom dead center (180 degrees) and the shut height should be measured. Without moving the slide that measurement should be entered here. This tells the system what the current shut height is. Press the “CONTINUE SLIDE CAL.” softkey.

g)The slide system should now be calibrated. Check for proper operation by running the slide up near the top of the adjustment range and checking the slide position reported. Note that linear transducers are repeatable but not absolutely accurate. This means the reported slide position may differ from the measured position by as much as .030". Repeat this process with the slide near the bottom of the adjustment range.

WARNING: After calibration always check for proper operation of the slide adjust system as wiring or transducer faults could cause an invalid calibration. Bad measurements could result in damage to the machine and tooling, and can cause injury or death.

Section 4.2.2.2 Calibrating Rotary Slide Adjust Systems

After setting the parameters in the previous section, the rotary slide system must be calibrated before it can be used.

IMPORTANT! Configuring/calibrating the slide adjust module should only be done with no dies installed in the press and, for presses equipped with slide counterbalance systems, should proceed only after the counterbalance is properly adjusted to offset the weight of the slide. If counterbalance pressure is too low, bearing clearances will cause shut height measurements made during calibration to be too small.

WARNING!

Since the slide adjust configuration procedure requires measurement of

 

the space between the press slide and bed or bolster, this procedure must

 

be performed with no dies or tooling in the press to prevent the possibility

 

of a point of operation or pinch point injury to personnel making the

 

measurement. Failure to heed this warning may result in serious injury

 

or death.

To calibrate a rotary slide adjust system:

a) Make sure the upper and lower limit settings have been set correctly in the slide configuration

April 17, 2000 Man ual Versio n 1.0

4.11

Page 34 Page 36
Page 35
Image 35
SMC Networks 5000 manual Calibrating Rotary Slide Adjust Systems, Or death
Page 34 Page 36

5000 specifications

SMC Networks 5000 is a robust and versatile networking solution designed to meet the demands of modern digital infrastructures. This device is a part of SMC Networks' extensive product lineup, which caters to both enterprise and small to medium-sized businesses. The SMC 5000 stands out due to its high performance, reliability, and advanced feature set.

One of the key features of the SMC Networks 5000 is its high-speed connectivity. It supports multiple Gigabit Ethernet ports, allowing for fast data transfer and seamless connectivity. This makes it ideal for environments where bandwidth is critical, such as in data centers, large office environments, and educational institutions. The device also includes advanced traffic management capabilities, ensuring efficient data flow and minimizing latency.

Another impressive characteristic of the SMC 5000 is its scalability. As organizations grow and their networking needs evolve, the SMC 5000 can adapt accordingly. It supports a modular design, allowing users to add or remove components based on their specific requirements. This flexibility enables businesses to optimize their network setup without the need for a complete overhaul.

Security is a top priority for SMC Networks, and the 5000 model incorporates advanced security features to protect sensitive data. With built-in firewalls, virtual private network (VPN) support, and robust encryption protocols, the device ensures that unauthorized access is prevented. This is particularly crucial in today’s digital landscape, where cyber threats are increasingly sophisticated.

In terms of management and monitoring, the SMC 5000 offers a user-friendly interface that simplifies network administration. Administrators can easily configure settings, monitor performance metrics, and troubleshoot issues through a centralized dashboard. This streamlines network management tasks and enhances overall efficiency.

The SMC Networks 5000 is also compatible with various networking technologies, including VLAN (Virtual Local Area Network) support, QoS (Quality of Service) features, and IPv6 readiness. These technologies contribute to a more efficient network setup and pave the way for future-proofing as networking standards evolve.

Overall, the SMC Networks 5000 is a reliable and powerful networking solution that provides the performance, security, and scalability necessary for today's demanding network environments. Its combination of advanced features and user-friendly management options makes it an excellent choice for businesses looking to enhance their networking infrastructure. With SMC Networks 5000, organizations can ensure seamless connectivity while effectively managing their growing digital demands.
Top Page Image Contents