c)The slide should travel no more than 1 inch per turn of the resolver.

d)The cable from the resolver to the OmniLink 5000 should not be run with any high voltage wiring (i.e. 120/240 VAC). In fact, this cable should be run in its own shielded conduit.

It is not necessary to know the exact gear ratio of slide travel to resolver turns - only that conditions “b” and “c” are met. The resolver may rotate in either direction relative to slide travel (i.e. the resolver may rotate clockwise or counter-clockwise as the slide goes down).

Section 3.6.2 Rotary Slide Adjust Wiring

A cable must go from the dual resolver mounted on the slide to the auto-setup board in the OmniLink 5000 extended card rack. Since the slide goes up and down relative to the machine, some means of stress relief must be used on the cable between the slide and the machine frame. The recommended method is to use a helical cable (same principle as a telephone handset cord) from the resolver to a junction box on the bottom of the crown. This lets the wire run in a “spring” pattern to help it resist breaking. Appendix B, Figure B.3 shows a conceptual view of this type of resolver mounting. The junction box should be grounded to the machine to help shield the connections inside.

NOTE: The cable should remain unbroken except for the connector in this junction box to keep the shield integrity - do not splice the cable!

Slide adjust motor starters with and without auxiliary contactors are supported. Solenoid air valves for air motors are also supported. Refer to Appendix B for typical wiring diagrams. Figures B.4 and B.5 show the wiring for two supported dual resolvers. Figures B.9 and B.10 show the wiring of slide adjust motor starters with and without auxiliary contactors. Figure B.11 shows the wiring of a slide adjust air motor. If an OmniLink 5000 control is ordered with a slide adjust system, then a wiring diagram will be provided as part of the documentation package.

Section 3.6.3 Linear Transducer Mounting

Linear shut height control makes use of linear magnetostrictive transducers. These transducers have a head that contains the electronics and a guide tube from 6" to 48" in length depending on the application. The guide tube is mounted to pass through (without touching) a separately mounted annular (doughnut shaped) magnet. The electronics sense the magnet location as the magnet moves up or down the guide tube when the slide is adjusted to provide shut height distance to the OmniLink 5000 control.

To install the linear transducer, there must be some point on the slide assembly that moves up and down with respect to a fixed point on the slide assembly when the shut height is changed. The transducer should be mounted to one point and the magnet to the other with strong, rigid, brackets. The particulars of mounting a linear transducer may vary greatly from press to press but keep in mind the following points:

a)Make sure there is adequate clearance from the transducer to the crown or other possible interference points of the press. A common mistake is mounting the transducer with the slide lowered and crushing the transducer when the slide is raised.

April 17, 2000 Man ual Versio n 1.0

3.10

Page 22 Page 24
Page 23
Image 23
SMC Networks 5000 manual Rotary Slide Adjust Wiring, Linear Transducer Mounting
Page 22 Page 24

5000 specifications

SMC Networks 5000 is a robust and versatile networking solution designed to meet the demands of modern digital infrastructures. This device is a part of SMC Networks' extensive product lineup, which caters to both enterprise and small to medium-sized businesses. The SMC 5000 stands out due to its high performance, reliability, and advanced feature set.

One of the key features of the SMC Networks 5000 is its high-speed connectivity. It supports multiple Gigabit Ethernet ports, allowing for fast data transfer and seamless connectivity. This makes it ideal for environments where bandwidth is critical, such as in data centers, large office environments, and educational institutions. The device also includes advanced traffic management capabilities, ensuring efficient data flow and minimizing latency.

Another impressive characteristic of the SMC 5000 is its scalability. As organizations grow and their networking needs evolve, the SMC 5000 can adapt accordingly. It supports a modular design, allowing users to add or remove components based on their specific requirements. This flexibility enables businesses to optimize their network setup without the need for a complete overhaul.

Security is a top priority for SMC Networks, and the 5000 model incorporates advanced security features to protect sensitive data. With built-in firewalls, virtual private network (VPN) support, and robust encryption protocols, the device ensures that unauthorized access is prevented. This is particularly crucial in today’s digital landscape, where cyber threats are increasingly sophisticated.

In terms of management and monitoring, the SMC 5000 offers a user-friendly interface that simplifies network administration. Administrators can easily configure settings, monitor performance metrics, and troubleshoot issues through a centralized dashboard. This streamlines network management tasks and enhances overall efficiency.

The SMC Networks 5000 is also compatible with various networking technologies, including VLAN (Virtual Local Area Network) support, QoS (Quality of Service) features, and IPv6 readiness. These technologies contribute to a more efficient network setup and pave the way for future-proofing as networking standards evolve.

Overall, the SMC Networks 5000 is a reliable and powerful networking solution that provides the performance, security, and scalability necessary for today's demanding network environments. Its combination of advanced features and user-friendly management options makes it an excellent choice for businesses looking to enhance their networking infrastructure. With SMC Networks 5000, organizations can ensure seamless connectivity while effectively managing their growing digital demands.
Top Page Image Contents