Password Settings, 4-17 | SMC Networks SMC7404BRA EU specification

SYSTEM SETTINGS

SYSTEM SETTINGS

Password Settings

Use this page to restrict access based on a password. By default, there is no password. For security you should assign one before exposing the Barricade to the Internet.

Passwords can contain from 3–12 alphanumeric characters and are not case sensitive.

Note: If your password is lost, or you cannot gain access to the user interface, press the reset button (colored blue) on the rear panel (holding it down for at least five seconds) to restore the factory defaults. (Default is no password.)

4-17

Image 42

SMC Networks SMC7404BRA EU manual Password Settings, 4-17, System Settings

Contents

Broadband Router with built-in ADSL Modem User GuidePage From SMC’s line of award-winning connectivity solutions December Part No 750.9701, UK Pub No 150000035400A COMPLIANCES FCC - Class BFCC - Part Industry Canada - Class B Australia AS/NZS 3548 1995 - Class BCOMPLIANCES EC Conformance Declaration - Class B COMPLIANCES 3 Configuring Client PCs TABLE OF CONTENTS2 Installation 4 Configuring the Barricade 5 Configuring Client TCP/IP TABLE OF CONTENTS 6 Configuring Printer Services TABLE OF CONTENTS Features and Benefits CHAPTER INTRODUCTIONAbout the Barricade VPN pass-through IPSec-ESP Tunnel mode, L2TP, PPTP Internet Access ApplicationsWired LAN Shared IP Address DMZ Host Support SecurityVirtual Private Network VPN CHAPTER INSTALLATION Package Contents System Requirements Hardware Description Description Condition LEDsVerify Status Status Connect the System Figure 2-1. Installing With a Splitter Phone Line ConfigurationInstalling a Full-rate Connection Connect the ADSL Line Installing a Splitterless Connection Figure 2-2. Installing Without a SplitterAttach to Your Network Using Ethernet Cabling Connect the Power Adapter TCP/IP Configuration CHAPTER 3 CONFIGURING CLIENT PCS CONFIGURING CLIENT PCS CHAPTER CONFIGURING THE BARRICADE Navigating the Web Browser Interface Making Configuration Changes Setup Wizard Time Zone Internet Sharing Parameter Setting Parameter Finish PPPoE & PPPoA Finish network, it will forward the packets to the Default SETUP WIZARDGateway usually your ISP will supply this address Multiple Protocol over ATM Mode 4-10 4-11 4-12 Advanced Setup ADVANCED SETUP4-13 The following table briefly describes the “Advanced Setup” menu items 4-14Menu Making Configuration Changes MAKING CONFIGURATION CHANGES4-15 System Settings 4-16 Password Settings SYSTEM SETTINGS4-17 Remote Management 4-18 4-19 PPPoE PPP over Ethernet 4-20 4-21 identifies the data channel within that virtual path then it is automatically forwarded to the default router i.e 4-221483 Bridging Bridging is a standardized layer 2 technology 4-23 4-24 4-25 4-26 Address Mapping 4-27 Virtual Server 4-28 The more common TCP service ports include 4-29 Routing System Static Route4-30 4-31 Authentication Required 4-32 Routing Table 4-33Parameter Description Firewall 4-34 Access Control 4-35FIREWALL The following items are on the “Access Control” screen 4-36 Access Control Add PC 4-37 URL Blocking 4-38 4-39 You may filter Internet access for local clients based on rulesSchedule Rule 1. Click “Add Schedule Rule.” 3. Click “OK” and then click “APPLY” to save your settings 4-40 Intrusion Detection 4-41 WAN port. When the SPI feature is turned on Enable SPI andlimits the access of the incoming traffic at the The Intrusion Detection feature of the Barricade 4-43 Stateful Packet If an IPX RIP request packet is not replied to by state structure remains active. When the timeout4-44 the router, it will stay in the input queue and not The length of time for which an H.323 session Parameter Defaults Description4-45 Maximum number of allowed incomplete TCP 4-46 Community SNMPSNMP 4-47 4-48 A community string password specified for trapTrap management. Enter a word, something other than ADSL ADSL4-49 Status 4-50 Maximum fluctuation in the output power 4-51Interleaved Path FEC Correction 4-52 Tools Configuration Tools4-53 Firmware Upgrade 4-54 Reset 4-55 Status 4-56 4-57 The following items are included on this screenSTATUS 4-58 Windows 95/98/Me CHAPTER 5 CONFIGURING CLIENT TCP/IP 2. In “Control Panel” double-click the “Network” icon TCP/IP Configuration Setting WINDOWS 95/98/ME Disable HTTP Proxy Internet Explorer Obtain IP Settings from Your ADSL Router Netscape Windows NT WINDOWS NT 11. Windows may copy some You need to verify that the “HTTP Proxy” feature of your Web browser is disabled. This is so that your browser can view the Barricade’s HTML configuration pages. Determine which browser you use and refer to “Internet Explorer” on page 5-4 or “Netscape” on page 4. Type “EXIT” and press ENTER to close the “Command Prompt” window Your computer is now configured to connect to the Barricade5-10 3. The connection status screen will open. Click “Properties.” Windows5-11 WINDOWS 5-12 4. Double-click “Internet Protocol TCP/IP.” 5-13 5-14 1. Click “start/Control Panel.” Windows XP5-15 2. In “Control Panel” click “Network and Internet Connections.” 5-16 5. Double-click “Internet Protocol TCP/IP.” 5-17 Type “EXIT” and press ENTER to close the “Command Prompt” window 5-18 Configuring Your Macintosh Computer CONFIGURING YOUR MACINTOSH COMPUTER5-19 3. If “Using DHCP Server” is already selected in the “Configure” field, your computer is already configured for DHCP. Close the TCP/IP dialog box, and skip to “Disable HTTP Proxy” on page 5-21.” 5-20 5-21 5-22 3. Select “Direct Connection to the Internet” and click “OK.” 5-23 5-24 CHAPTER CONFIGURING PRINTER SERVICES Install the Printer Port MonitorSkip this section if you are using Unix INSTALL THE PRINTER PORT MONITOR CONFIGURING PRINTER SERVICES Configure the Print Server Configure the Network Printer in Windows 95/98/Me/2000 4. Select the monitored port. The default port name is “SMC100.” Click the “Configure Port” button Configure the Network Printer in Windows NT Configure the Network Printer in Unix Systems CONFIGURE THE PRINT SERVER APPENDIX A TROUBLESHOOTING Page Page TROUBLESHOOTING APPENDIX B CABLES Ethernet Cable RJ-45 Port Ethernet Connection Pin Assignments Straight-Through Wiring Crossover Wiring ADSL Cable Connection Signal Name Not usedFigure B-3. RJ-11 Pinouts CABLES APPENDIX C SPECIFICATIONS Page LIMITED WARRANTY SMCs Limited Warranty Statement LIMITED WARRANTY Contact SMC Full Installation ManualFirmware and Drivers Statement of Conditions