4-12, Parameter, Description | SMC Networks SMC7404BRA EU specification

CONFIGURING THE BARRICADE

Parameter	Description
DHCP Parameters
Default Gateway	The default gateway IP address. If the Barricade
	cannot find the destination address within its local
	network, it will forward the packets to the Default
	Gateway (usually your ISP will supply this
	address.)
Subnet Mask	The network subnet mask.
Name Server 1	Primary name server IP address.
Name Server 2	Alternate name server IP address.
Name Server 3	Alternate name server IP address.
Start IP Address	Start IP Address of DHCP assigned IP addresses.
Number of IP	Number of IPs available for assignment by the
	DHCP server.

Your Barricade is now setup. Go to “Troubleshooting” on page A-1 if you cannot make a connection to the Internet.

4-12

Image 37

SMC Networks SMC7404BRA EU manual 4-12, Parameter, Description

Contents

User Guide Broadband Router with built-in ADSL ModemPage Part No 750.9701, UK Pub No 150000035400A From SMC’s line of award-winning connectivity solutions December FCC - Class B COMPLIANCESFCC - Part Australia AS/NZS 3548 1995 - Class B Industry Canada - Class BCOMPLIANCES EC Conformance Declaration - Class B COMPLIANCES 2 Installation TABLE OF CONTENTS3 Configuring Client PCs 4 Configuring the Barricade TABLE OF CONTENTS 5 Configuring Client TCP/IP 6 Configuring Printer Services TABLE OF CONTENTS CHAPTER INTRODUCTION Features and BenefitsAbout the Barricade VPN pass-through IPSec-ESP Tunnel mode, L2TP, PPTP Wired LAN ApplicationsInternet Access Shared IP Address Security DMZ Host SupportVirtual Private Network VPN Package Contents CHAPTER INSTALLATION System Requirements Description Hardware Description Verify Status LEDsCondition Status Connect the System Installing a Full-rate Connection Phone Line ConfigurationFigure 2-1. Installing With a Splitter Connect the ADSL Line Figure 2-2. Installing Without a Splitter Installing a Splitterless ConnectionAttach to Your Network Using Ethernet Cabling Connect the Power Adapter CHAPTER 3 CONFIGURING CLIENT PCS TCP/IP Configuration CONFIGURING CLIENT PCS CHAPTER CONFIGURING THE BARRICADE Making Configuration Changes Navigating the Web Browser Interface Time Zone Setup Wizard Internet Sharing Parameter Parameter Setting Finish PPPoE & PPPoA Parameter SETUP WIZARD network, it will forward the packets to the DefaultGateway usually your ISP will supply this address 4-10 Multiple Protocol over ATM Mode 4-11 4-12 ADVANCED SETUP Advanced Setup4-13 4-14 The following table briefly describes the “Advanced Setup” menu itemsMenu MAKING CONFIGURATION CHANGES Making Configuration Changes4-15 4-16 System Settings SYSTEM SETTINGS Password Settings4-17 4-18 Remote Management 4-19 4-20 PPPoE PPP over Ethernet identifies the data channel within that virtual path 4-21 4-22 then it is automatically forwarded to the default router i.e1483 Bridging Bridging is a standardized layer 2 technology 4-23 4-24 4-25 4-26 4-27 Address Mapping 4-28 Virtual Server 4-29 The more common TCP service ports include Static Route Routing System4-30 4-31 4-32 Authentication Required 4-33 Routing TableParameter Description 4-34 Firewall 4-35 Access ControlFIREWALL 4-36 The following items are on the “Access Control” screen 4-37 Access Control Add PC 4-38 URL Blocking Schedule Rule You may filter Internet access for local clients based on rules4-39 1. Click “Add Schedule Rule.” 4-40 3. Click “OK” and then click “APPLY” to save your settings 4-41 Intrusion Detection limits the access of the incoming traffic at the Enable SPI andWAN port. When the SPI feature is turned on The Intrusion Detection feature of the Barricade Stateful Packet 4-43 4-44 state structure remains active. When the timeoutIf an IPX RIP request packet is not replied to by the router, it will stay in the input queue and not 4-45 Parameter Defaults DescriptionThe length of time for which an H.323 session Maximum number of allowed incomplete TCP 4-46 SNMP SNMPCommunity 4-47 Trap A community string password specified for trap4-48 management. Enter a word, something other than ADSL ADSL4-49 4-50 Status 4-51 Maximum fluctuation in the output powerInterleaved Path FEC Correction 4-52 Configuration Tools Tools4-53 4-54 Firmware Upgrade 4-55 Reset 4-56 Status The following items are included on this screen 4-57STATUS 4-58 CHAPTER 5 CONFIGURING CLIENT TCP/IP Windows 95/98/Me 2. In “Control Panel” double-click the “Network” icon WINDOWS 95/98/ME TCP/IP Configuration Setting Internet Explorer Disable HTTP Proxy Netscape Obtain IP Settings from Your ADSL Router Windows NT WINDOWS NT 11. Windows may copy some You need to verify that the “HTTP Proxy” feature of your Web browser is disabled. This is so that your browser can view the Barricade’s HTML configuration pages. Determine which browser you use and refer to “Internet Explorer” on page 5-4 or “Netscape” on page Your computer is now configured to connect to the Barricade 4. Type “EXIT” and press ENTER to close the “Command Prompt” window5-10 5-11 Windows3. The connection status screen will open. Click “Properties.” WINDOWS 4. Double-click “Internet Protocol TCP/IP.” 5-12 5-13 5-14 5-15 Windows XP1. Click “start/Control Panel.” 2. In “Control Panel” click “Network and Internet Connections.” 5. Double-click “Internet Protocol TCP/IP.” 5-16 5-17 5-18 Type “EXIT” and press ENTER to close the “Command Prompt” window CONFIGURING YOUR MACINTOSH COMPUTER Configuring Your Macintosh Computer5-19 5-20 3. If “Using DHCP Server” is already selected in the “Configure” field, your computer is already configured for DHCP. Close the TCP/IP dialog box, and skip to “Disable HTTP Proxy” on page 5-21.” 5-21 3. Select “Direct Connection to the Internet” and click “OK.” 5-22 5-23 5-24 Install the Printer Port Monitor CHAPTER CONFIGURING PRINTER SERVICESSkip this section if you are using Unix INSTALL THE PRINTER PORT MONITOR CONFIGURING PRINTER SERVICES Configure the Network Printer in Windows 95/98/Me/2000 Configure the Print Server 4. Select the monitored port. The default port name is “SMC100.” Click the “Configure Port” button Configure the Network Printer in Windows NT Configure the Network Printer in Unix Systems CONFIGURE THE PRINT SERVER APPENDIX A TROUBLESHOOTING Page Page TROUBLESHOOTING Ethernet Cable APPENDIX B CABLES Pin Assignments RJ-45 Port Ethernet Connection Crossover Wiring Straight-Through Wiring ADSL Cable Connection Not used Signal NameFigure B-3. RJ-11 Pinouts CABLES APPENDIX C SPECIFICATIONS Page SMCs Limited Warranty Statement LIMITED WARRANTY LIMITED WARRANTY Firmware and Drivers Full Installation ManualContact SMC Statement of Conditions