WINDOWS 95/98/ME | SMC Networks SMC7404BRA EU instruction

WINDOWS 95/98/ME

WINDOWS 95/98/ME

6.Click the “Gateway” tab and record the numbers listed under “Installed gateways.”

7.Click the “DNS Configuration” tab. Locate the DNS servers listed under “DNS Server Search Order.” Record any listed addresses.

8.After writing down your settings, check to make sure you have recorded them correctly. Click the “IP Address” tab and then click “Obtain an IP address automatically.” Click “OK.”

9.Windows may need your Windows 95/98/Me CD to copy some files. After it finishes copying, it will prompt you to restart your system. Click “Yes” and your computer will shut down and restart.

TCP/IP Configuration Setting

IP Address	____.____.____.____
Subnet Mask	____.____.____.____
Primary DNS Server	____.____.____.____
Secondary DNS Server	____.____.____.____
Default Gateway	____.____.____.____
Host Name	____.____.____.____

5-3

Image 86

SMC Networks SMC7404BRA EU manual WINDOWS 95/98/ME, TCP/IP Configuration Setting

Contents

Broadband Router with built-in ADSL Modem User GuidePage From SMC’s line of award-winning connectivity solutions December Part No 750.9701, UK Pub No 150000035400A FCC - Part COMPLIANCESFCC - Class B COMPLIANCES Industry Canada - Class BAustralia AS/NZS 3548 1995 - Class B EC Conformance Declaration - Class B COMPLIANCES 3 Configuring Client PCs TABLE OF CONTENTS2 Installation 4 Configuring the Barricade 5 Configuring Client TCP/IP TABLE OF CONTENTS 6 Configuring Printer Services TABLE OF CONTENTS About the Barricade Features and BenefitsCHAPTER INTRODUCTION VPN pass-through IPSec-ESP Tunnel mode, L2TP, PPTP Internet Access ApplicationsWired LAN Shared IP Address Virtual Private Network VPN DMZ Host SupportSecurity CHAPTER INSTALLATION Package Contents System Requirements Hardware Description Description Condition LEDsVerify Status Status Connect the System Figure 2-1. Installing With a Splitter Phone Line ConfigurationInstalling a Full-rate Connection Connect the ADSL Line Attach to Your Network Using Ethernet Cabling Installing a Splitterless ConnectionFigure 2-2. Installing Without a Splitter Connect the Power Adapter TCP/IP Configuration CHAPTER 3 CONFIGURING CLIENT PCS CONFIGURING CLIENT PCS CHAPTER CONFIGURING THE BARRICADE Navigating the Web Browser Interface Making Configuration Changes Setup Wizard Time Zone Internet Sharing Parameter Setting Parameter Finish PPPoE & PPPoA Description Gateway usually your ISP will supply this address network, it will forward the packets to the DefaultSETUP WIZARD Multiple Protocol over ATM Mode 4-10 4-11 4-12 4-13 Advanced SetupADVANCED SETUP Menu The following table briefly describes the “Advanced Setup” menu items4-14 4-15 Making Configuration ChangesMAKING CONFIGURATION CHANGES System Settings 4-16 4-17 Password SettingsSYSTEM SETTINGS Remote Management 4-18 4-19 PPPoE PPP over Ethernet 4-20 4-21 identifies the data channel within that virtual path 1483 Bridging Bridging is a standardized layer 2 technology then it is automatically forwarded to the default router i.e4-22 4-23 4-24 4-25 4-26 Address Mapping 4-27 Virtual Server 4-28 The more common TCP service ports include 4-29 4-30 Routing SystemStatic Route 4-31 Authentication Required 4-32 Parameter Description Routing Table4-33 Firewall 4-34 FIREWALL Access Control4-35 The following items are on the “Access Control” screen 4-36 Access Control Add PC 4-37 URL Blocking 4-38 4-39 You may filter Internet access for local clients based on rulesSchedule Rule 1. Click “Add Schedule Rule.” 3. Click “OK” and then click “APPLY” to save your settings 4-40 Intrusion Detection 4-41 WAN port. When the SPI feature is turned on Enable SPI andlimits the access of the incoming traffic at the The Intrusion Detection feature of the Barricade 4-43 Stateful Packet If an IPX RIP request packet is not replied to by state structure remains active. When the timeout4-44 the router, it will stay in the input queue and not The length of time for which an H.323 session Parameter Defaults Description4-45 Maximum number of allowed incomplete TCP 4-46 Community SNMPSNMP 4-47 4-48 A community string password specified for trapTrap management. Enter a word, something other than 4-49 ADSLADSL Status 4-50 Interleaved Path FEC Correction Maximum fluctuation in the output power4-51 4-52 4-53 ToolsConfiguration Tools Firmware Upgrade 4-54 Reset 4-55 Status 4-56 STATUS 4-57The following items are included on this screen 4-58 Windows 95/98/Me CHAPTER 5 CONFIGURING CLIENT TCP/IP 2. In “Control Panel” double-click the “Network” icon TCP/IP Configuration Setting WINDOWS 95/98/ME Disable HTTP Proxy Internet Explorer Obtain IP Settings from Your ADSL Router Netscape Windows NT WINDOWS NT 11. Windows may copy some You need to verify that the “HTTP Proxy” feature of your Web browser is disabled. This is so that your browser can view the Barricade’s HTML configuration pages. Determine which browser you use and refer to “Internet Explorer” on page 5-4 or “Netscape” on page 5-10 4. Type “EXIT” and press ENTER to close the “Command Prompt” windowYour computer is now configured to connect to the Barricade 3. The connection status screen will open. Click “Properties.” Windows5-11 WINDOWS 5-12 4. Double-click “Internet Protocol TCP/IP.” 5-13 5-14 1. Click “start/Control Panel.” Windows XP5-15 2. In “Control Panel” click “Network and Internet Connections.” 5-16 5. Double-click “Internet Protocol TCP/IP.” 5-17 Type “EXIT” and press ENTER to close the “Command Prompt” window 5-18 5-19 Configuring Your Macintosh ComputerCONFIGURING YOUR MACINTOSH COMPUTER 3. If “Using DHCP Server” is already selected in the “Configure” field, your computer is already configured for DHCP. Close the TCP/IP dialog box, and skip to “Disable HTTP Proxy” on page 5-21.” 5-20 5-21 5-22 3. Select “Direct Connection to the Internet” and click “OK.” 5-23 5-24 Skip this section if you are using Unix CHAPTER CONFIGURING PRINTER SERVICESInstall the Printer Port Monitor INSTALL THE PRINTER PORT MONITOR CONFIGURING PRINTER SERVICES Configure the Print Server Configure the Network Printer in Windows 95/98/Me/2000 4. Select the monitored port. The default port name is “SMC100.” Click the “Configure Port” button Configure the Network Printer in Windows NT Configure the Network Printer in Unix Systems CONFIGURE THE PRINT SERVER APPENDIX A TROUBLESHOOTING Page Page TROUBLESHOOTING APPENDIX B CABLES Ethernet Cable RJ-45 Port Ethernet Connection Pin Assignments Straight-Through Wiring Crossover Wiring ADSL Cable Connection Figure B-3. RJ-11 Pinouts Signal NameNot used CABLES APPENDIX C SPECIFICATIONS Page LIMITED WARRANTY SMCs Limited Warranty Statement LIMITED WARRANTY Contact SMC Full Installation ManualFirmware and Drivers Statement of Conditions