Routing System, Static Route, 4-30 | SMC Networks SMC7404BRA EU

Routing System

CONFIGURING THE BARRICADE

Routing System

These pages define routing related parameters, including static routes and RIP (Routing Information Protocol) parameters.

Static Route

Parameter	Description
Index	Check the box of the route you wish to delete or
	modify.
Network Address	Enter the IP address of the remote computer you
	wish to set a static route to.
Subnet Mask	Enter the subnet mask of the remote network you
	wish to set a static route to.
Gateway	Enter the WAN IP address of the gateway to the
	remote network.

Click “Add” to add a new static route to the list, or check the box of an already entered route and click “Modify.” Clicking “Delete” will remove an entry from the list.

4-30

Image 55

SMC Networks SMC7404BRA EU manual Routing System, Static Route, 4-30

Contents

User Guide Broadband Router with built-in ADSL ModemPage Part No 750.9701, UK Pub No 150000035400A From SMC’s line of award-winning connectivity solutions December FCC - Class B COMPLIANCESFCC - Part Australia AS/NZS 3548 1995 - Class B Industry Canada - Class BCOMPLIANCES EC Conformance Declaration - Class B COMPLIANCES 4 Configuring the Barricade TABLE OF CONTENTS2 Installation 3 Configuring Client PCs TABLE OF CONTENTS 5 Configuring Client TCP/IP 6 Configuring Printer Services TABLE OF CONTENTS CHAPTER INTRODUCTION Features and BenefitsAbout the Barricade VPN pass-through IPSec-ESP Tunnel mode, L2TP, PPTP Shared IP Address ApplicationsWired LAN Internet Access Security DMZ Host SupportVirtual Private Network VPN Package Contents CHAPTER INSTALLATION System Requirements Description Hardware Description Status LEDsVerify Status Condition Connect the System Connect the ADSL Line Phone Line ConfigurationInstalling a Full-rate Connection Figure 2-1. Installing With a Splitter Figure 2-2. Installing Without a Splitter Installing a Splitterless ConnectionAttach to Your Network Using Ethernet Cabling Connect the Power Adapter CHAPTER 3 CONFIGURING CLIENT PCS TCP/IP Configuration CONFIGURING CLIENT PCS CHAPTER CONFIGURING THE BARRICADE Making Configuration Changes Navigating the Web Browser Interface Time Zone Setup Wizard Internet Sharing Parameter Parameter Setting Finish PPPoE & PPPoA Parameter SETUP WIZARD network, it will forward the packets to the DefaultGateway usually your ISP will supply this address 4-10 Multiple Protocol over ATM Mode 4-11 4-12 ADVANCED SETUP Advanced Setup4-13 4-14 The following table briefly describes the “Advanced Setup” menu itemsMenu MAKING CONFIGURATION CHANGES Making Configuration Changes4-15 4-16 System Settings SYSTEM SETTINGS Password Settings4-17 4-18 Remote Management 4-19 4-20 PPPoE PPP over Ethernet identifies the data channel within that virtual path 4-21 4-22 then it is automatically forwarded to the default router i.e1483 Bridging Bridging is a standardized layer 2 technology 4-23 4-24 4-25 4-26 4-27 Address Mapping 4-28 Virtual Server 4-29 The more common TCP service ports include Static Route Routing System4-30 4-31 4-32 Authentication Required 4-33 Routing TableParameter Description 4-34 Firewall 4-35 Access ControlFIREWALL 4-36 The following items are on the “Access Control” screen 4-37 Access Control Add PC 4-38 URL Blocking 1. Click “Add Schedule Rule.” You may filter Internet access for local clients based on rulesSchedule Rule 4-39 4-40 3. Click “OK” and then click “APPLY” to save your settings 4-41 Intrusion Detection The Intrusion Detection feature of the Barricade Enable SPI andlimits the access of the incoming traffic at the WAN port. When the SPI feature is turned on Stateful Packet 4-43 the router, it will stay in the input queue and not state structure remains active. When the timeout4-44 If an IPX RIP request packet is not replied to by Maximum number of allowed incomplete TCP Parameter Defaults Description4-45 The length of time for which an H.323 session 4-46 4-47 SNMPSNMP Community management. Enter a word, something other than A community string password specified for trapTrap 4-48 ADSL ADSL4-49 4-50 Status 4-51 Maximum fluctuation in the output powerInterleaved Path FEC Correction 4-52 Configuration Tools Tools4-53 4-54 Firmware Upgrade 4-55 Reset 4-56 Status The following items are included on this screen 4-57STATUS 4-58 CHAPTER 5 CONFIGURING CLIENT TCP/IP Windows 95/98/Me 2. In “Control Panel” double-click the “Network” icon WINDOWS 95/98/ME TCP/IP Configuration Setting Internet Explorer Disable HTTP Proxy Netscape Obtain IP Settings from Your ADSL Router Windows NT WINDOWS NT 11. Windows may copy some You need to verify that the “HTTP Proxy” feature of your Web browser is disabled. This is so that your browser can view the Barricade’s HTML configuration pages. Determine which browser you use and refer to “Internet Explorer” on page 5-4 or “Netscape” on page Your computer is now configured to connect to the Barricade 4. Type “EXIT” and press ENTER to close the “Command Prompt” window5-10 WINDOWS Windows5-11 3. The connection status screen will open. Click “Properties.” 4. Double-click “Internet Protocol TCP/IP.” 5-12 5-13 5-14 2. In “Control Panel” click “Network and Internet Connections.” Windows XP5-15 1. Click “start/Control Panel.” 5. Double-click “Internet Protocol TCP/IP.” 5-16 5-17 5-18 Type “EXIT” and press ENTER to close the “Command Prompt” window CONFIGURING YOUR MACINTOSH COMPUTER Configuring Your Macintosh Computer5-19 5-20 3. If “Using DHCP Server” is already selected in the “Configure” field, your computer is already configured for DHCP. Close the TCP/IP dialog box, and skip to “Disable HTTP Proxy” on page 5-21.” 5-21 3. Select “Direct Connection to the Internet” and click “OK.” 5-22 5-23 5-24 Install the Printer Port Monitor CHAPTER CONFIGURING PRINTER SERVICESSkip this section if you are using Unix INSTALL THE PRINTER PORT MONITOR CONFIGURING PRINTER SERVICES Configure the Network Printer in Windows 95/98/Me/2000 Configure the Print Server 4. Select the monitored port. The default port name is “SMC100.” Click the “Configure Port” button Configure the Network Printer in Windows NT Configure the Network Printer in Unix Systems CONFIGURE THE PRINT SERVER APPENDIX A TROUBLESHOOTING Page Page TROUBLESHOOTING Ethernet Cable APPENDIX B CABLES Pin Assignments RJ-45 Port Ethernet Connection Crossover Wiring Straight-Through Wiring ADSL Cable Connection Not used Signal NameFigure B-3. RJ-11 Pinouts CABLES APPENDIX C SPECIFICATIONS Page SMCs Limited Warranty Statement LIMITED WARRANTY LIMITED WARRANTY Statement of Conditions Full Installation ManualFirmware and Drivers Contact SMC