REMOTE menu

The REMOTE menu is used to assign the functions to the pins of the PARALLEL REMOTE terminal.

Pin 1 to 4 and pin 6 to 8 can be used. The following lists the functions you can assign to the pins.

•– – (No function is assigned.)•LINE A•LINE B•RGB/COMP (for the PVM-14L2/PVM-20L2 only)•OPTION A•OPTION B•TALLY•UNDERSCAN•16:9•EXT SYNC•BLUE ONLY•DEGAUSS

Note

If you use the parallel remote function, you need to connect cables.For more details, see page 33. OPTION CONFIG menu

The OPTION CONFIG menu is used to set the optional board installed in the option slot on the rear panel. Depending on the board installed, the screen displayed may differ. If no board is installed, the item settings are not displayed. After assigning the input signal, be sure to adjust the monitor’s AUTO CHROMA/PHASE.

When installing the BKM-150CP optional board:

Submenu

Setting

FORMAT

Sets the signal type.

 

Select SDTI-CP or D1-SDI.

 

 

AUDIO

Selects an audio channel.

 

D1-SDI

 

Select from among CH1+CH2

 

through CH15+CH16, or CH1

 

through CH16.

 

SDTI-CP

 

Select from among CH1+CH2

 

through CH7+CH8, or CH1

 

through CH8.

 

The audio signal input to the

 

OPTION AUDIO INPUT 1/2 jack

 

is ignored.

 

 

TIME CODE

Selects the time code display.

 

D1-SDI

 

Select VITC, RP188 or OFF.

 

SDTI-CP

 

Select VITC, CP-TC1, CP-TC2,

 

ES-TC1, ES-TC2 or OFF.

 

 

The following lists the abbreviations in the menu and their full names:

• CP-TC1:

SMPTE 331M System Item USER DATE/TIME

 

 

STAMP

• CP-TC2:

SMPTE 331M System Item CREATION DATE/

 

 

TIME STAMP

•

ES-TC1:

SMPTE 328M MPEG ES Editing Information

 

 

TIME CODE1

•

ES-TC2:

SMPTE 328M MPEG ES Editing Information

 

 

TIME CODE2

•

RP188:

SMPTE RP188 Time Code

• VITC:

SMPTE 12M VITC, SMPTE 266M D-VITC

When installing the BKM-155DV optional board:

Submenu

Setting

AUDIO

Selects an audio channel.

 

Select from among CH1+CH2,

 

CH3+CH4, CH1/3, CH2/4, CH1/

 

3+CH2/4, or CH1 through CH4.

 

OPTION AUDIO INPUT 1/2 jack

 

is ignored.

 

 

When installing the BKM-120D or BKM-129X optional board:The serial number of the board is displayed on the OPTION CONFIG menu.

If the cooling fan in the BKM-150CP or BKM-155DV is stopped, the screen shows the following message in red “BKM-xxxxx FAN ERROR”. In this case, you cannot select Option A or Option B.

Troubleshooting

This section may help you isolate the cause of a problem and as a result, eliminate the need to contact technical support.

•The display is colored green or purple. t Select the correct input by pressing one of the buttons related to input.

•The signal input through the RGB/COMPONENT input connectors does not appear on the screen (for the PVM-14L2/PVM-20L2 only). t Set RGB/ COMP SEL on the USER CONFIG menu appropriately according to type of input signal.

•The BKM-150CP or BKM-155DV has been installed. The error message “BKM-xxxxx FAN ERROR” is displayed and you cannot select Option A or Option B. t Repair the BKM-xxxxx.

30 Troubleshooting