Input Fader Request 0x52 0x50 0x4D 0x35 ‘RPM5’ | Sony SRP-X500P

SRP-X500P RS-232C Interface Manual

•FADER (1st-6th byte)

The level for each fader can be specified (in dB units).

The parameter and levels are as shown in the following table.

Level		Level			Level
-∞	0x30 (‘0’)	-20.0	0x40	(‘@’)	-4.5	0x50	(‘P’)
-70.0	0x31 (‘1’)	-19.0	0x41	(‘A’)	-4.0	0x51	(‘Q’)
-60.0	0x32 (‘2’)	-18.0	0x42	(‘B’)	-3.5	0x52	(‘R’)
-55.0	0x33 (‘3’)	-17.0	0x43	(‘C’)	-3.0	0x53	(‘S’)
-50.0	0x34 (‘4’)	-16.0	0x44	(‘D’)	-2.5	0x54	(‘T’)
-45.0	0x35 (‘5’)	-15.0	0x45	(‘E’)	-2.0	0x55	(‘U’)
-40.0	0x36 (‘6’)	-14.0	0x46	(‘F’)	-1.5	0x56	(‘V’)
-35.0	0x37 (‘7’)	-13.0	0x47	(‘G’)	-1.0	0x57	(‘W’)
-32.5	0x38 (‘8’)	-12.0	0x48	(‘H’)	-0.5	0x58	(‘X’)
-30.0	0x39 (‘9’)	-11.0	0x49	(‘I’)	0	0x59	(‘Y’)
-27.5	0x3A (‘:’)	-10.0	0x4A (‘J’)		+0.5	0x5A (‘Z’)
-25.0	0x3B (‘;’)	-9.0	0x4B (‘K’)		+1.0	0x5B (‘[‘)
-24.0	0x3C (‘<‘)	-8.0	0x4C (‘L’)		+1.5	0x5C (‘\’)
-23.0	0x3D (‘=‘)	-7.0	0x4D (‘M’)		+2.0	0x5D (‘]’)
-22.0	0x3E (‘>‘)	-6.0	0x4E (‘N’)		+2.5	0x5E (‘^’)
-21.0	0x3F (‘?’)	-5.0	0x4F (‘O’)		+3.0	0x5F (‘_’)

Level
+3.5	0x60	(‘`’)
+4.0	0x61	(‘a’)
+4.5	0x62	(‘b’)
+5.0	0x63	(‘c’)
+5.5	0x64	(‘d’)
+6.0	0x65	(‘e’)
+6.5	0x66	(‘f’)
+7.0	0x67	(‘g’)
+7.5	0x68	(‘h’)
+8.0	0x69	(‘i’)
+8.5	0x6A (‘j’)
+9.0	0x6B (‘k’)
+10.0	0x6C (‘l’)

Example

To set the level for each input fader as follows:

MIC 1/WL 1 INPUT : -10dB

MIC 2/WL 2 INPUT : -10dB

MIC 3 INPUT	: -10dB
MIC 4 INPUT	: -10dB
LINE INPUT	: 0dB
AV/RGB INPUT	: 0dB

0x43 0x50 0x4D 0x35 0x4A 0x4A 0x4A 0x4A 0x59 0x59 0x0D (‘C P M 5 J J J J Y Y CR’)

2.1.4 INPUT FADER REQUEST : 0x52 0x50 0x4D 0x35 (‘RPM5’)

This command is used to read the input fader settings from the SRP-X500P.

Packet format

0x52 0x50 0x4D 0x35 0x0D

Return packet format

When the SRP-X500P receives the command successfully, the parameter is returned together with an ACK (0x41 (‘A’)) in the order shown below.

0x41 “parameter” 0x0D

The parameter consists of 6 bytes of data which are the same as those of the parameter of the INPUT FADER command.

Page 8/43

Image 8

Sony SRP-X500P manual Input Fader Request 0x52 0x50 0x4D 0x35 ‘RPM5’, Fader 1st-6th byte

Contents

SRP-X500P Table of Contents 3 4 Connecting the SRP-X500P to a ComputerAbout This Manual Communication Protocol RS-232C indicatorCommunication Format Handshake Codes Communication Packet Format Basic Control Commands 1 AV/RGB Input Select 0x43 0x53 0x45 0x4C ‘CSEL’ Input Fader 0x43 0x50 0x4D 0x35 ‘CPM5’ Return packet format Input Fader Request 0x52 0x50 0x4D 0x35 ‘RPM5’ Fader 1st-6th byte Fader 1st-8th byte Output Fader 0x43 0x50 0x4D 0x40 ‘CPM@’Output Fader Request 0x52 0x50 0x4D 0x40 ‘RPM@’ Remote Remote 1-6 Level 0x43 0x4C 0x56 0x4C ‘CLVL’Channel 1st byte Level 2nd byte Remote 1-6 Level 2nd-7th byte Master Volume UP 0x43 0x4C 0x56 0x2B ‘CLV+’Master Volume Level 1st byte Master Volume Down 0x43 0x4C 0x56 0x2D ‘CLV-’ Master Volume Stop 0x43 0x4C 0x56 0x53 ‘CLVS’ Muting 0x43 0x4D 0x55 0x54 ‘CMUT’ Muting 2nd byte Speaker Output Muting 2nd byte Muting Parameter Request 0x52 0x4D 0x55 0x54 ‘RMUT’Input Muting 1st byte Line Output Muting 3rd byte Master Muting 4th byteRemote Muting 5th byte Master Projector ON/STANDBY 0x43 0x50 0x4A 0x50 ‘CPJP’ Projector Control Request 1st byte Projector ON/STANDBY Indicator 1st byte Scene Recall 0x43 0x52 0x43 0x4C ‘CRCL’Scene Recall Request 1st byte Scene Recall Request Scene Recall Parameter Request 0x52 0x52 0x43 0x4C ‘RRCL’ Scene No st byte Index Status Acquisition CommandsIndex Request 0x52 0x50 0x4D 0x44 ‘RPMD’ Level Meter Parameter Request 0x52 0x4D 0x54 0x52 ‘RMTR’ Level Meter 1st-16th byte To acquire status of single item To acquire the status of all items Parameters Remote 1-6 Level 10th-15th byte Input Volume 3rd-8th byteMaster Volume Level 9th byte Input Muting 30th byte Input Level 16th-21st byteOutput Level 22nd-29th byte Output Muting 31st and 32nd byte Speaker Output MutingLine Output Muting Master Muting 33rd byte RF/AF Indicator 36th byte WL Indicator 37th byte+48V Switch 38th byte MIC 1-4 Trim 39th-42nd byte AV/RGB Trim 44th-48th byte REF Indicator 49th byteLine Trim 43rd byte FR 50th-53rd byte FR Setup Status 54th and 55th byteSetup Channel Setup Status AV/RGB Input Select 56th byteSpeaker Output Level 57th, 58th byte Speaker Output CH1/2 Level IR Output Mode Indicator 59th byte Clip Indicator 77th byteLevel Meter 60th-75th byte Protection 76th byte Temperature 78th and 79th byte TemperatureProjector ON/STANDBY Indicator 80th byte EMG Muting 83rd byte Scene No th byte Parallel Input 85th-94th byteLevel Parallel Output 95th and 96th byte Master Volume Control 98th byte OutputFAN Motor 97th byte OUT6 OUT5 OUT4 OUT3 OUT2 Gain Reduction 99th-108th byte AGC Gain Control Compressor Gain Reduction Maintenance Information Commands Information SETUPDATE2005/01/23Information Request 0x52 0x50 0x4D 0x45 ‘RPME’ Information Maintenance Information Read Write Maintenance Information Read Write Maintenance Information Read only Maintenance Information Read only Version Version Request 0x52 0x56 0x45 0x52 ‘RVER’Version Factory Preset 0x43 0x52 0x53 0x54 ‘CRST’