Other Hookups
Components the Up Hooking
|
|
|
|
|
|
|
| ||
| ANTENNA | TV/LD | DVD | VIDEO 2 | VIDEO 1 | MONITOR |
| ||
DIGITAL |
|
|
|
|
|
|
|
|
|
DVD IN | AM |
|
|
|
|
|
|
| WOOFER + |
|
|
|
|
|
|
|
| ||
OPTICAL |
|
|
|
|
|
|
|
| |
TV / LD IN |
| VIDEO | VIDEO | VIDEO | VIDEO | VIDEO | VIDEO | VIDEO | AUDIO |
| OUT | ||||||||
|
| IN | IN | OUT | IN | OUT | IN | OUT |
|
OPTICAL | y |
|
|
|
|
|
| CTRL A1 |
|
|
|
|
|
|
|
|
| ||
MD/DAT IN |
|
|
|
|
|
|
|
| – |
OPTICAL | COAXIAL | AUDIO | AUDIO | AUDIO | AUDIO | AUDIO | AUDIO |
| |
| FM | IN | IN | OUT | IN | OUT | IN |
|
|
MD/DAT OUT |
|
|
|
|
|
|
|
| |
75Ω |
|
|
|
|
|
| L |
| |
OPTICAL |
|
|
|
|
|
|
|
|
|
DVD IN |
|
|
|
|
|
|
| R | A |
|
|
|
|
|
|
|
| ||
COAXIAL | SIGNAL |
|
|
|
|
|
|
|
|
| IN | IN | RECOUT | IN | RECOUT | IN |
| R + | |
| GND |
| |||||||
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
| L | |
|
|
|
|
|
|
|
|
| |
| y |
|
|
|
|
|
| R | B |
|
|
|
|
|
|
|
|
| |
|
| PHONO | CD | MD/DAT | TAPE |
|
| ||
Required cords
CONTROL A1 connecting cord (not supplied)
Black | Black |
AC power cord | AC OUTLET* |
REARCENTER
AC OUTLET
+
WIRELESS IMPEDANCE
RLREAR SELECTOR
SPEAKER
FRONT
– | 4 Ω 8 Ω |
A
VOLTAGE SELECTOR
– | – | + | L | 220 V | |
240 V | |||||
|
|
|
| ||
|
|
| B | 120 V | |
|
|
|
|
FRONT
SPEAKERS
| b |
* The configuration, shape, and number of AC outlets on the rear panel | To a wall outlet |
varies according to the model and country to which the receiver is |
|
shipped. |
|
•If you have a
Use a CONTROL A1 cord (not supplied) to connect the
Note
If you make CONTROL A1 connections from the receiver to an MD deck that is also connected to a computer, do not operate the receiver while using the “Sony MD Editor” software. This may cause a malfunction.
•If you have a Sony CD changer with a COMMAND MODE selector
If your CD changer’s COMMAND MODE selector can be set to CD 1, CD 2, or CD 3, be sure to set the command mode to “CD 1” and connect the changer to the CD jacks on the receiver.
If, however, you have a Sony CD changer with VIDEO OUT jacks, set the command mode to “CD 2” and connect the changer to the VIDEO 2 jacks on the receiver.
Setting the voltage selector
Check that the voltage selector on the rear panel of the receiver is set to the local power supply voltage. If not, use a screwdriver to set the selector to the correct position before connecting the AC power cord to a wall outlet.
VOLTAGE SELECTOR
220V
240V
120V