Connect the printer to the computer | Star Micronics NX-2400

Connect the printer to the computer

Connect the printer end of the interface cable to the connector socket on the right side of the printer as shown in Figure 1-6.

Make sure the computer is turned OFF, then connect the other end of the cable to your computer as described in the computer manual

terface cable

Check that the printer’s power switch (located at the left front) is OFF. Then plug the printer’s power cord into an AC wall outlet.

Never plug or unplug the power cord while the printer is turned on.

LOADING SINGLE SHEETS

This section will take you through the procedures for loading single sheets of paper.

If you are using the optional automatic sheet feeder (ASF), read the ASF instruction booklet.

Mount the paper guide

The paper guide fits into the two holes on top of the rear cover. Mount the guide and raise it to the upright position.

6

Image 14

Star Micronics NX-2400 user manual Connect the printer to the computer, Mount the paper guide

Contents

NX-2400 Page HOW to USE this Manual Features of the Printer Quad-sized Tableofcontents With DOS and Basic Download Character Generator Chapter Platen Setting UP Remove the top cover Install the ribbon cartridge Install the optional IC card Replace the top cower Connect the printer to the computer Mount the paper guide Semiautomatic loading Figure l-7.Mounting the paper guide for single sheets Manual loading Loading and Parking Fanfold Forms 11. Closing the sprocket covers Paper parking Paper unparking Short se/f test Long se/f test Interface test Adjusting the Printing GAP International character set Print style and pitch selection Page Page OFF Control Panel OPERAllONS On Line switch Paper Feed switch Quiet Mode switch Sty/e/Pitch switch POWER-UP Functions Sh0ff test paffern On Line switch Lprint CHR$I Next B8 B9 Switch Combination Functions Switch combination functions of control panel Top Of fOff?L Style/Pitch Page Memo Using WE PR//vER Installing Your Software Command options Printer Setting the DIP Switches Using Your Software Type sty/e and pitch selection Printercommands Memo Using the Printer with DOS and Basic HARD-COPYING the Screen MS-DOS and PC-DOS Programming the Printer with DOS Commands Name of list device PRN New file Programming the Printer with Basic Acopy LQELITE.DAT PRN Aprint README.DOC ‘Cancel Lprint the Spacings are Changed Next H How the program works IBM Lprint ES= cHR$ocHR$6ocHR$6o Cleaning the Printer Replacing the Ribbon Replacing the Print Head Replacing the ribbon cartrlctge Connector cover Fligure 5-2. Replacing the print head Replacing the Battery in the RAM Card If a// text is printed on the same line TroubleshootingIf printing is faint, incomplete, or unclear If line spacing is twice as wide as expected If you have problems with horizontal tabulation If you have problems with graphicsIf you have problems with download characters Interface and Emulation Switches and fndicatorsPrinting Mechanism Character Sets Dot Matrix Size Type Sty/es and Pitches Paper SpecificationsDimensions and Weight Environmental Requirements Electrical SpecificationsInterface Signals Option Signal Pin No Name Memo Font Control Commands Select draft quality characters Select ornament character Select LQ charactersSelect LQ type Style Select Italic Characters Start Underlining Select Upright CharactersDouble-strike Printing Start Overlining Cancel Superscript Or subscriptStop Underlining Stop Overlining Select character set #7 Select Standard characterSelect IBM character set Select Character set #2 Select s/ash zero Enable printing of all character codesEnable printing of a// character codes on next character Select normal zero High-speed elite pitch Pica pitchElite pitch High-density elite pitch Condensed printing Cancel condensed printingCancel expanded printing Expanded printing Se/ect proportional spacing Select master print modeCaucel one-line expanded printing Select fixed spacing Print double-height characters Increase character SpacingSelect double or quadruple size Return to normal Height Select Character Width Select character height, width, and line spacing Set line spacing to 7160 or 7172 inch Vertical Position CommandsSelect character type and print pitch Set line spacing to 718 inch Set line spacing to n/780 or n/216 inch Set line spacing to 716 inchSet base unit for line spacing Set line spacing to n/360 inch Define line spacing to n/72 inch Select forward feed modeSelect reverse feed mode Execute ESC a Feed paper n lines Perform one n/180-inch or n/2164nch line feedPerform one n/780-inch reverse line feed Set top of page at current position Set top margin Cancel top and bottom marginsSet page length to n inches Set bottom margin Set vertical tab stops Disable paper-out detectorEnable paper-out detector Set vertical tab stops every n lines Set left margin Select Vertical Tab channelVertical tab Set right margin Carriage return Cancel automatic line feedSet left and right margins Set automatic Line feed Center text BackspaceLeff justify Right justify Set horizontal tab stop every n columns Reset all tab stopsSet horizontal tab stops Horizontal tab Absolute horizontal tab in inches Relative horizontal TabRelative horizontal tab in inches Absolute horizontal tab in columns Print 8-bit double-density graphics Graphics CommandsPrint 8-bit single-density graphics Print 8-bit double-density, double-speed graphics Select graphics mode Print M-bit hex-density graphics Download Character Convert graphics densityCopy standard characters from ROM into RAM Define Download Select download character set ROM Other Printer Control CommandsDelete Last character Sent MSB Quiet Print Cancel Quiet PrintRepeat data Last Line Set printer on-line Cancel Immediate PrintSet printer off-line Stop printing One-line unidirectional printing PrintingUnidirectional printing Manual feed Set print start position on ASF Reset printerEject Paper Memo AppendixCDOWNLOAD Norma/ character Semi-condensed Proportional Super/subscript character Iiao 1600 2440 If ST=5 then CLS Goto 3480 Character Sets I7’ Standard Character SET Pj-iii-j IBM Character SET #2 Page IBM CH Aracter SET #I Additional Character SET International Character Sets SfR Index Lol 111 107 Command Summary ESC ESC p ESC p0 ESC p.‘ 111