Manuals / Sterling / Household Appliance / Dehumidifier

Sterling SDAA 25-100 specifications Dryer Operation Procedures

Models: SDAA 25-100

1 60

Download 60 pages 53.38 Kb

Page 35

4-3 Dryer Operation Procedures

Controller Operation (Without Optional Alarm Horn & Reset Button)

1.Turn the disconnect on the control panel to the ON position. Power is applied to the voltage line fuses, line side of the control power switch and the temperature controller.

2.Turn the control power switch to the ON position. Power is applied to the programmable relay and dew point controller. The valve will move to the start position as follows:

a.The valve motor rotates until the cam switch makes 2 transitions.

b.If the cam switch does not make a transition within 10 seconds, a valve motor fault is generated. “VALVE MTR” is displayed on the relay screen, the alarm light is activated. The valve motor, heaters, and blower shut off.

To restart the dryer, cycle control power to deactivate the alarm light and restart the valve motor sequence.

Note: The relay screen which contains the Alarm Display Messages is located inside the controller enclosure. For a list of Alarm Display Messages, see Page 35.

WARNING! Do not attempt to check the Alarms on the Controller located within the unit enclosure unless you are a qualified electrician!

c.The valve will normally complete one full cycle (revolution).

If the drying process shuts down due to an alarm, the dryer has been setup to have the following operational features:

•The bed in process at power-down will remain in process.

•The bed in regeneration at power-down will remain in regeneration.

•The regeneration timing cycle will restart from the beginning.

Dehumidifying Dryers

Chapter 4: Operation

34 of 59

Image 35

Sterling SDAA 25-100 specifications Dryer Operation Procedures

Contents

Sdaa 25-100 15-60 cfm Dehumidifying Dryers Shipping Information Table of Contents Maintenance Service Department Sales Department Contract Department Safety Symbols Used in this Manual SafetyHow to Use This Manual Wear Safety Glasses and Work Gloves General Responsibility ResponsibilityRemember Operator ResponsibilityReporting a Safety Defect Maintenance ResponsibilityDehumidifying Dryers Safety General Description Functional DescriptionModels Covered in This Manual Electrical Features Standard FeaturesWhat is desiccant? Mechanical FeaturesOptions Safety Devices and InterlocksController Features Fail Safe Operation Safety Circuit StandardsSafety Device Lock-Outs Rigging and Placing the Dryer InstallationUncrating the Equipment Machine-Mount Dryer Dimensions Floor-Mount Dryer Dimensions Recommended Dryer Lifting Hardware Suggested Lift Rigging for Cart Mounted DryersSuggested Lift Rigging for Machine Mounted Dryers Electrical ConnectionsMaking Dryer/Drying Hopper Process Air Connections Setup ProceduresThree-Phase Models Checking for Proper Blower RotationOptional Aftercooler Installing Water Lines Hose and Hose ClampDrying Hopper Air Trap Considerations Starting Up the Dryer Auto-Tuning the DryerInitial Start-up Pre-Startup ChecksShutting Down the Dryer Start-up OperationController Description and Operation SwitchesIndicator Lights Lit when Control Output 2 is on. Not used Process Air Temperature ControllerLit when Control Output 1 is on. The Out1 Setting the Process Air Temperature Indicator Name DescriptionLights in the Operation Indicator Section when Identifying Temperature Controller KeysE5CN Operating Parameters Tuned prior to dryer startup Adjustment Level Indicator Name DescriptionON, OFF Entering Operating Parameters to Select ModesOptional Setting the High Dew Point AlarmProcess Air Dew Point Display Watlow Operating Parameters Redundant Safety Controller DisplaySetting the Redundant Safety Controller Mode Parameter Setting range Default Manf. setting Dryer Operation Procedures Model Heating Cooling 15 cfm 30 cfm 60 cfm Page Controller Operation With Optional Alarm Horn & Reset Button Page Alarm Display Messages Shutting Down the Dryer Auto-Tuning the DryerPhotocopy this page for your maintenance records MaintenancePreventative Maintenance Schedule Vacuuming Preventative MaintenanceRecommendations for Cleaning and Replacing Filters Servicing Process Air FiltersServicing the Dew Point Monitor Cleaning with Compressed AirSymptoms of Worn Desiccant Corrective MaintenanceReplacing Worn Desiccant First AIDConsult local disposal regulations for more information Replacing the Process Heater ProceduresIntroduction TroubleshootingProblem Possible cause Corrective action Problem Possible cause Corrective action Check resin manufacturer’s data Using a Platinum Resistance Thermometer Determining Temperature Controller Errors or Sensor ErrorsUsing a Thermocouple Appendix WarrantyWarranty Specifications Warranty RestrictionsCustomer Responsibilities Warranty LiabilitiesOptional Components Annex B Information Technical SpecificationsAftercooler Design Specifications Drawings and Diagrams Spare Parts ListLevel 2 & 3 Spare Parts List Electrical & Mechanical Returned Material Policy Safety Tag InformationWarranty Returns Dryer Safety TagsLocated on back of Dryer Dryer Identification Serial Number TagSales Department Service DepartmentTechnical Assistance Parts Department