To Recover From a Corrupt SP | Sun Microsystems X4150 specs

▼To Recover From a Corrupt SP

1.Copy all SP files from the Tools and Drivers CD to a USB flash device.

The SP files are located in the BMCrecovery directory, on the Tools and Drivers CD. They consist of:

■SOCFLASH.EXE

■DOS4GW

■BMC Binary (SP Binary file)

2.Remove AC power from system to be flashed.

Note – Do not attempt to flash the system while it is still powered on. An unrecoverable error might occur.

3.Remove the server’s top cover.

4.Using a jumper cap, short the pins at jumper JP20 on the server motherboard.

JP20 is located toward the rear of the board. See the Sun Fire X4150 Server Service Manual for the precise location.

5.Insert the bootable flash drive into the USB port.

6.Connect AC power and power on the system.

a.A message appears stating that the BMC was not found. The system takes up to three minutes to boot.

b.Press F2 to enter system BIOS and verify that the Flash device is in the boot order.

7.Once the flash device is booted, run the following command: socflash.exe SP binary backup file

For example:

socflash.exe s92v092.bin backup.bin

8.After a successful flash, remove the AC power and jumper, and leave the system powered off for up to 30 seconds.

9.Power on the system.

10.Confirm that the SP is listed in the BIOS settings under Server/AST2000 LAN Configuration.

Chapter 4 Configuring, Managing and Maintaining the Server Using the Web-Based Interface 47

Image 63

Sun Microsystems X4150 manual To Recover From a Corrupt SP

Contents

Sun Microsystems, Inc Page Contents To Access the Elom Using a Web Browser To Clear the Event Log Using the Remote Console Application Using the Command-Line Interface Using Ipmi Using Simple Network Management Protocol Glossary Index Command-LineInterface ReferencePage Figures Page How This Document Is Organized Preface Using Unix Commands Related Documentation Typographic Conventions Sun Documentation, Support, and Training Third-Party Web SitesSun Welcomes Your Comments Sun Fire X4150 server Elom Overview Sun Fire X4150 server Elom Features Embedded Lights Out Manager Common Tasks1ELOM Common Tasks 2SP Controller and Firmware Default Settings Sun Fire X4150 server Default Settings About the Indicator and Fault LEDs About the Preconfigured Administrator Account Connecting to the Elom About Connection Tasks Connecting Using a Serial ConnectionTo Connect Using a Serial Connection 1Methods of Connecting to the Elom Connecting Using Ethernet Enter the following commandLog in to the CLI Enter the following command -exit Connecting to the CLI Click the Log Out button Click LogPage Using the Web-Based Interface Monitoring the Server System Using the Web-Based Interface Browser and Software Requirements Users and PrivilegesWeb-Based Interface Tasks To Access the Elom Using a Web Browser Accessing the Elom Using a Web Browser 1ELOM Tab Detail Choices Viewing the System From the Web Browser User Management On the main menu, click the System Information tab Viewing System and Component InformationTo View System Information Viewing Version Information To View SP Version Information 3Sample Server Board Information Viewing Component Information To View CPU Information 4Sample CPU Information 6Sample Memory for DIMMA0 Monitoring the System SensorsViewing Memory Information To View Memory Information 5Sample Memory Information To Monitor the System Sensors Reading Sensors To Read SensorsOn the main menu, click System Monitoring From the Sensor Reading tab, select the Summary tab Viewing a Sensor Summary To View a Sensor Summary CPU 0 Temp Too high From the Sensor Reading tab, select the Fan tab Monitoring Temperatures To Monitor TemperaturesFrom the Sensor Reading tab, select the Temperature tab Monitoring Fans To Monitor Fans 14Sample of the Voltage Monitor Screen Monitoring Voltages To Monitor VoltageViewing and Managing the Event Log From the Sensor Reading tab, click the Voltage tab From the Event Logs tab, select View Event Logs To Display the Event LogTo View the Event Logs To Save the Event Log To Clear the Event Log Chapter Configuring the System From the main menu, click the Configuration tab To Configure the System From the Configure submenu, click the Network tab Configuring E-mail NotificationTo Configure E-mail Notification Configuring Platform Event Filters To Configure a Platform Event Filter Options are Ffh All sensors Configuring System Management Access To access the System Management Access SubmenusClick Submit to create the filter Configuring Snmp Click Generate to create a new CSR1Example of Required SSL Information To Add an Snmp Community To Configure Snmp To Delete an Snmp Community To Modify an Snmp CommunityTo Add an Snmp User Click Submit to create the new user Configuring Active Directory ServiceTo Delete an Snmp User To Edit an Snmp User To Configure Active Directory Service Managing and Maintaining the SystemManaging Users and Accounts To Add a User 3The User Management Screen Type a password in the Password field To Change a User Password or Privilege To Disable or Enable a UserTo Delete a User Account Managing the System Locator Indicator LED To Control the State of the System Indicator LEDManaging the Front Panel and On-Board Fault LEDs To Turn the Fault LEDs Off To View the State of the Fault LEDs To Reset the Service Processor Setting Power ControlTo Set Power Control Resetting the Service Processor Updating the Firmware Using a Web Browser Click Reset SP buttonUpdating the Firmware To Update the Firmware Using a Web Browser Recovering from a Corrupt SPSelect the firmware file or Cpld file to update To Recover From a Corrupt SP Click the Submit button to set the session timeout Managing Session TimeoutTo Set the Session Timeout To Disable the Session Timeout From the Configuration submenu, click the Set Time tab Setting the Time To Set the TimePage Requirements Accessing the Remote Console CD and Diskette Redirection Operational Model 1Client Installation Requirements 2Remote Console Operation With DVD Drive and Diskette Drive Click Launch Click LoginStarting the Remote Console Application To Start the Remote Console Application Setting Parameters for the Remote Console From the Remote Control submenu, select Hotkey SetupTo Set Parameters for the Remote Console To Redirect Keyboard and Mouse Devices Redirecting Keyboard, Video, Mouse, or Storage Devices Select a source device from the drop-down list To Redirect Storage Devices Installing an Operating System on a Remote Server To Install an OS on a Remote Server Using a Virtual CD-ROMType the user name and password in the login screen Other Remote Options Page About Ipmi Using Ipmi Sensors IPMItool 1Supported Ipmi 2.0 Commands Supported Ipmi 2.0 Commands General Commands 2Supported Ipmi 2.0 Commands FRU Device Commands Serial/Modem Device Commands 2Supported Ipmi 2.0 Commands Page Logging In to the CLI Using the Command-Line Interface Syntax Command Syntax 2CLI Options 1CLI Command Verbs Managing the Host State Managing the Host Viewing Host Sensors Managing the Host Console Managing Elom Network Settings To Display Network SettingsTo Configure Network Settings Targets, Properties, and Values Managing Local User Accounts With Enter the following command show /SP/users To Delete a User Account Using the CLITo Display User Accounts Using the CLI Enter the following command delete /SP/users/username Configuring User Accounts Managing Alerts Displaying AlertsTo Display Alerts Output of the show command appears Configuring Alerts Configuring the PEF Global Controls Configuring the Event Filter Tables To Configure the PEF Global Controls To Configure the Event Filter Tables Result of executing the show command appears To Display the Current SP Version Information Displaying Version Information To Update the Firmware To update the firmware, enter one of the following commandsUpdating the Firmware Select Yes to continue, or No to exit Start the Tftp downloadPage How Snmp Works About Snmp MIBs Integration Snmp MIB Files 1Sun Server MIB Tree Snmp Messages Adding Your Server to Your Snmp Environment Configuring Snmp on the ElomConfiguring Receipt of Snmp Traps Managing Snmp User Accounts 1SNMP Targets, Properties, and Values Deleting a User Account Show Table A-1Command Syntax and Usage CLI Command Quick Reference Table A-2General Commands Table A-3User CommandsTable A-4Network and Serial Port Setting Commands Table A-5Alert Commands Table A-6SNMP CommandsTable A-7System Start, Stop, and Reset Commands Set /SYS/CtrlInfo PowerCtrl=reset CLI Command Reference Example Create Table A-9delete Command Targets DeleteExit Usage load -source URL target Help Set Table A-10set Command Targets, Properties, and Values SP/AgentInfo/SNMP/user Show Start Start Command Target Reset Table A-12stop Command TargetStop Version Page Glossary Access control listAddress Resolution Advanced Configuration Power Interface Alert Standard Format Advanced Programmable Interrupt ControllerAdvanced Technology Advanced Technology Attachment Packet Certificate Authority Bios Basic Customer-replaceable Command-line interfaceCommon Information Coordinated Universal Distinguished Name Direct memory accessDomain name server Domain name service Digital Signature Electrically erasable programmable read- only memory Dynamic Host Configuration ProtocolDynamic random access Domain Name System Dual inline memory Field-replaceable unit Erasable programmable read-only memoryExternally initiated Fibre Channel Arbitrated Loop Graphical user interface File Transfer ProtocolFully qualified domain Grand Unified Hypertext Transfer Hypertext Transfer Protocol SecureIn-band system Interrupt request Intelligent Platform Management InterfaceInternet Control Message Protocol Internet Protocol IP Keyboard, video, mouse, storage Java Web StartJumpStart Keyboard Controller Local area network Lightweight Directory Access ProtocolLightweight Directory Access Protocol Ldap Media access control Network interface card Nonvolatile random access memoryNetwork file system Network Information Peripheral Interface Object identifierOut-of-band OOB Peripheral Component Platform Event Trap Power-on self-testPreboot Execution Platform Event Filter Programmable read- only memory Remote procedure call Redundant array of independent disksRemote Management Control Protocol Server Message Block Secure Sockets LayerSensor data record Serial Attached Scsi System event log Simple Network Management ProtocolSmall Computer System Interface Spanning Tree Protocol Trivial File Transport Uninterruptible powerTransmission control Transmission Control Protocol/Internet Voltage regulator User identificationUserID a unique string identifying a user to a system User identification number UIDPage Index LED Index