Receiving an all ships call | Sunpentown Intl FM-8800D/8800S

3. DSC OPERATION FOR NON-DISTRESS CASES

3.4.2Receiving an all ships call

In case of ON HOOK

1.When an all ships call is received, the audio alarm sounds and the display looks something like the one shown below.

All ships

call received.

FROM : 123456789

SAFETY

TCmd1 : SIMPLEX TP

TCmd2 : NO INFO

CH : 16

CANCEL ALARM

2.Press the CANCEL or ENT key to silence the alarm. The display changes as follows.

**Received Message **

APR01/í04 12 : 34 ECC : OK

ALL SHIPS CALL

FROM : 123456789

SAFETY

TCmd1 : SIMPLEX TP

TCmd2 : NO INFO

CH : 16

PRESS ENT TO CHANGE CH

3.Press the ENT key. The display changes to the standby display, indicating channel specified, and you can watch the contents of the message.

In case of OFF HOOK

1.When an all ships call is received, the audio alarm sounds and the ALARM LED blinks.

2.Press the ACK key. The display changes to the standby display, indicating channel specified.

Note: Before pressing the ACK key, if you press the CANCEL key, the alarm stops. Press the CANCEL key again to cancel the all ship call, or press the ENT key to accept the all ship call and the display changes to the standby display, indicating channel specified.

3-18

Image 62

Sunpentown Intl FM-8800D/8800S Receiving an all ships call, Press ENT to Change CH, Case of on Hook, Case of OFF Hook

Contents

VHF Radiotelephone 00014993015 Canceling Distress Alert Example message Safety Instructions Important Notices Table of Contents DSC Operation for NON-DISTRESS Cases System Setup Vii ForewordWord to FM-8800D/FM-8800S Owners Viii FeaturesProgram number System Configuration MAX This page is intentionally left blank SP-1 General SP-2 CH70 Watch Receiver Front panel Operational OverviewControls Keys and LCD Indication Controls Push to Enter ABC Shift 116 Indications on the LCD Audio alarms Auto Selecting channel modes, channels Turning the power on and adjusting contrastVHF Basic Operation Selecting channel modes Selecting output power Adjusting volume of loudspeakerAdjusting squelch Transmitting Scanning Quick selection of CH16Dual watch Remarks on voice communications DSC operational overview DSC Operational OverviewLED warnings Standby display Automatic acknowledge on/off Distress alert transmission and output powerWhen keyboard input is prohibited Preparing and transmitting DSC messages How to set priority of the remote station Priority Call Type Distress DSC Distress CommunicationDistress Alert Transmission from the Distress Key Nature Undesignated Distress ACK Cancel AlarmTime to GO 4M 12S Press ENT Distress communication Distress Alert Transmission with Nature of DistressNatureundesignated Simp TP UndesignatedCall Type Distress To Coast AAA Distress Alert Transmission from Call KeyCall Type Coast Call Routine Canceling a False Distress Alert Input Type Auto Procedure when in area A1 Vessel able Transmitting Dist ACK signal Transmitting Dist ACK over CH16 Simp TP Press Call to Send DistressPress ENT to ACK After transmitting Dist ACK Sending distress relay to coast station When you should relay a distress alertSending Distress Relay on Behalf of a Ship in Distress Coast ID Routine Auto Coast IDInput Type Auto Sending distress relay to all ships Call Type Relay SEL Call Type Relay ALL ID in Dist no Info Call Type Relay ALL Receiving Distress RelayReceiving distress relay all call Receiving distress relay from coast station Distress Relay ALL Press ENT This page is intentionally left blank Coast or Ship Call General procedure for transmitting a coast or ship callDSC Operation for NON-DISTRESS Cases Sending a coast or ship call Select CH CH no Info Receiving acknowledgement of coast or ship callTime to GO 3M30 S Unable acknowledge call received Receiving a coast or ship callAble acknowledge call received No response! Try calling again? Coast ACK Sending automatic acknowledge ACK BQ with comply status Able Coast ACK Routine Ship Call Manually acknowledging individual call with Able Ship ACK Routine Manually acknowledging a coast or ship call with Unable Sending a group call Busy Equip Disbld Mode Unavail CH UnavailGroup Call No Reason Press the ENTkeytoopen the calltypelist Receiving a group call Press ENT Pstn Call Sending a Pstn call Pstn call disconnection ship disconnects line Pstn call disconnection coast station disconnects line Receiving a Pstn call All Ships Call Sending an all ships call Select CH Case of on Hook Receiving an all ships callPress ENT to Change CH Case of OFF Hook Call Type Area Call Geographical Area CallSending a geographical area call Select CH Receiving a geographical area call Position Call Position call requesting other ships position Cancel Alarm Manual reply Position call other ship requests your positionAutomatic reply Position Call Polling CallSending a polling call Response is received+*. *!#$% Receiving a polling call Polling ACK Routine Polling Call Receiving a neutral craft call Neutral Craft CallSending a neutral craft call Call Type Neutral Craft Medical Transport Call Sending a medical transport call Receiving a medical transport call Urgency Ship ACK Log FileOpening a log file Ship Call Answer Delete Received LOG Are YOU SURE? Yesno This page is intentionally left blank Alarm Basic SetupAlarm Setup Old position alarm in manual position entry mode Safety OFF To set type of alarm to output Unable Reason No Reason Position Call on Polling Call on Auto ACK SetupComply Status Able Able To set polling call response To set reason for unableTo set position call response Rcvd Ordinary Erasing LogsErase LOG Menu Rcvd Distress Transmitted Memory Channel Setup 01 CH Message File 1/13 Message File EntryAuto ACK Erase LOG Memory Channel Message File Entry Coast Call Ship ID Group IDArea Select CH #$#!% Position Position SetupPrint OUT Volume System Manual Rcvd Call Manual Daily Test Manual Print Out SetupXmtd Call Manual Earpiece volume Volume SetupEarpiece Level Setup EXT ENT Intercom volume Off-hook loudspeaker Displaying Group ID List System SetupDisplaying Self ID Position Print OUT Volume Test System Naming Intercom Displaying Program Version Group ID List Intercom Naming Program Version This page is intentionally left blank Troubleshooting Maintenance & TroubleshootingMaintenance When the power cannot be turned on CPU PCB TX Power TX/RX PCBDaily Test CH70 RX PCB OK Transceiver unit FM-8800D/8800S Error MessageParts Location Junction box IF-8810 Handset HS-2003Remote station RB-8800/RB-8810/RB-8810-W/HS-8800/HS-8800-W DMC Interface IF-8820 AP-1 AppendixMenu Tree AP-2 Appendix Marine VHF Channel Lists AP-3 AP-4 AP-5 AP-6 AP-7 Private Channels AP-8 AP-9 157.500 AP-10 AP-11 AP-12 AP-13 Load requirements as listner Digital Interface IEC 61162-1 EditionInput sentences Output sentence AP-15 GGA -Global positioningsystem GPS fixdata GNS-GNSS fixed data AP-16 RMC Recommemded minimum specific GPS/TRANSIT data AP-17 TLL Target latitude and longitude AP-18 Printer usage cautions Specifications, Parts of the PrinterThermal Printer UTP-80FK Paper usage cautions Parts OperationAP-20 Loading roll paper AP-21 Front panel Setting the DIP switch AP-22 Remedy for paper jam AP-23Printing test Adjusting printing intensity AP-24 UTP-58E for RC-8800S/D-B Rack Console and PP-8800A Printer Paper replacementThermal Printer UTP-58E AP-25 AP-26 Index IN-1 IN-2 0560