Press ENT | Sunpentown Intl FM-8800D/8800S specs

3. DSC OPERATION FOR NON-DISTRESS CASES

If a response from the coast station is received within five seconds, transmit PSTN CALL (EOS) signal and then carrier frequency during two seconds. Then your phone rings. Press the CANCEL key to stop the calling sound and change to standby display. Hook off and communicate with other party.

Note: If using a hand-microphone, pressing the CANCEL key is equal to off-hook.

3.3.2PSTN call disconnection (ship disconnects line)

1.After hanging up the handset or pressing the CANCEL key to complete your call, the display shows the following message. The end of call signal is transmitted; and the system then waits for a response from the coast station.

Waiting for acknowledgement

FROM : 003456789

TCmd1 : DUPLEX TP

TCmd2 : PAY-PHONE

TEL : 1234567890123456

CH : 28

2.When the ACK from the coast station is received, the following display appears. The communication time (charge time) is informed.

Able acknowledge call received.

FROM : 003456789

TCmd1 : END CALL

TCmd2 : NO INFO

TEL : 1234567890123456

CHARGE TIME : 00h05m18s

PRESS ENT

3-14

Image 58

Sunpentown Intl FM-8800D/8800S manual Pstn call disconnection ship disconnects line, Press ENT

Contents

VHF Radiotelephone 00014993015 Canceling Distress Alert Example message Safety Instructions Important Notices Table of Contents DSC Operation for NON-DISTRESS Cases System Setup Word to FM-8800D/FM-8800S Owners ForewordVii Program number FeaturesViii System Configuration MAX This page is intentionally left blank SP-1 General SP-2 CH70 Watch Receiver Controls Keys and LCD Indication Operational OverviewFront panel Controls Push to Enter ABC Shift 116 Indications on the LCD Audio alarms Auto Selecting channel modes, channels Turning the power on and adjusting contrastVHF Basic Operation Selecting channel modes Selecting output power Adjusting volume of loudspeakerAdjusting squelch Transmitting Scanning Quick selection of CH16Dual watch Remarks on voice communications DSC operational overview DSC Operational OverviewLED warnings Standby display Automatic acknowledge on/off Distress alert transmission and output powerWhen keyboard input is prohibited Preparing and transmitting DSC messages How to set priority of the remote station Priority Call Type Distress DSC Distress CommunicationDistress Alert Transmission from the Distress Key Nature Undesignated Distress ACK Cancel AlarmTime to GO 4M 12S Press ENT Natureundesignated Distress Alert Transmission with Nature of DistressDistress communication Call Type Distress UndesignatedSimp TP To Coast AAA Distress Alert Transmission from Call KeyCall Type Coast Call Routine Canceling a False Distress Alert Input Type Auto Procedure when in area A1 Vessel able Transmitting Dist ACK signal Transmitting Dist ACK over CH16 Simp TP Press Call to Send DistressPress ENT to ACK After transmitting Dist ACK Sending distress relay to coast station When you should relay a distress alertSending Distress Relay on Behalf of a Ship in Distress Coast ID Routine Input Type Auto Coast IDAuto Sending distress relay to all ships Call Type Relay SEL Call Type Relay ALL ID in Dist no Info Receiving distress relay all call Receiving Distress RelayCall Type Relay ALL Receiving distress relay from coast station Distress Relay ALL Press ENT This page is intentionally left blank DSC Operation for NON-DISTRESS Cases General procedure for transmitting a coast or ship callCoast or Ship Call Sending a coast or ship call Select CH Time to GO 3M30 S Receiving acknowledgement of coast or ship callCH no Info Unable acknowledge call received Receiving a coast or ship callAble acknowledge call received No response! Try calling again? Coast ACK Sending automatic acknowledge ACK BQ with comply status Able Coast ACK Routine Ship Call Manually acknowledging individual call with Able Ship ACK Routine Manually acknowledging a coast or ship call with Unable Sending a group call Busy Equip Disbld Mode Unavail CH UnavailGroup Call No Reason Press the ENTkeytoopen the calltypelist Receiving a group call Press ENT Pstn Call Sending a Pstn call Pstn call disconnection ship disconnects line Pstn call disconnection coast station disconnects line Receiving a Pstn call All Ships Call Sending an all ships call Select CH Case of on Hook Receiving an all ships callPress ENT to Change CH Case of OFF Hook Sending a geographical area call Geographical Area CallCall Type Area Call Select CH Receiving a geographical area call Position Call Position call requesting other ships position Cancel Alarm Automatic reply Position call other ship requests your positionManual reply Sending a polling call Polling CallPosition Call Response is received+*. *!#$% Receiving a polling call Polling ACK Routine Polling Call Receiving a neutral craft call Neutral Craft CallSending a neutral craft call Call Type Neutral Craft Medical Transport Call Sending a medical transport call Receiving a medical transport call Urgency Ship ACK Log FileOpening a log file Ship Call Answer Delete Received LOG Are YOU SURE? Yesno This page is intentionally left blank Alarm Basic SetupAlarm Setup Old position alarm in manual position entry mode Safety OFF To set type of alarm to output Unable Reason No Reason Position Call on Polling Call on Auto ACK SetupComply Status Able Able To set position call response To set reason for unableTo set polling call response Rcvd Ordinary Erasing LogsErase LOG Menu Rcvd Distress Transmitted Memory Channel Setup 01 CH Message File 1/13 Message File EntryAuto ACK Erase LOG Memory Channel Message File Entry Coast Call Area Group IDShip ID Select CH #$#!% Position Position SetupPrint OUT Volume System Manual Xmtd Call Manual Print Out SetupRcvd Call Manual Daily Test Manual Earpiece volume Volume SetupEarpiece Level Setup EXT ENT Intercom volume Off-hook loudspeaker Displaying Self ID System SetupDisplaying Group ID List Position Print OUT Volume Test System Naming Intercom Displaying Program Version Group ID List Intercom Naming Program Version This page is intentionally left blank Troubleshooting Maintenance & TroubleshootingMaintenance When the power cannot be turned on CPU PCB TX Power TX/RX PCBDaily Test CH70 RX PCB OK Parts Location Error MessageTransceiver unit FM-8800D/8800S Junction box IF-8810 Handset HS-2003Remote station RB-8800/RB-8810/RB-8810-W/HS-8800/HS-8800-W DMC Interface IF-8820 Menu Tree AppendixAP-1 AP-2 Appendix Marine VHF Channel Lists AP-3 AP-4 AP-5 AP-6 AP-7 Private Channels AP-8 AP-9 157.500 AP-10 AP-11 AP-12 AP-13 Load requirements as listner Digital Interface IEC 61162-1 EditionInput sentences Output sentence AP-15 GGA -Global positioningsystem GPS fixdata GNS-GNSS fixed data AP-16 RMC Recommemded minimum specific GPS/TRANSIT data AP-17 TLL Target latitude and longitude AP-18 Printer usage cautions Specifications, Parts of the PrinterThermal Printer UTP-80FK Paper usage cautions Parts OperationAP-20 Loading roll paper AP-21 Front panel Setting the DIP switch AP-22 Printing test AP-23Remedy for paper jam Adjusting printing intensity AP-24 UTP-58E for RC-8800S/D-B Rack Console and PP-8800A Printer Paper replacementThermal Printer UTP-58E AP-25 AP-26 Index IN-1 IN-2 0560