Polling Call, Position Call | Sunpentown Intl FM-8800D/8800S

3.DSC OPERATION FOR NON-DISTRESS CASES

2.Press the CANCEL key to silence the alarm.

**Received Message **

APR01/04 12 : 34 ECC : OK

POSITION CALL

FROM : 123456789

ROUTINE

TCmd1 : POSITION

TCmd2 : NO INFO

PRESS ENT TO ACK.

3.To send your position manually, press the ENT key. The following pop-up menu appears.

ANSWER

NO ANSWER

4.Choose ANSWER by the CH knob and press the CALL key to send your position data. Then, the standby display appears.

To send no position data, choose NO ANSWER and press the ENT key twice to return to the standby display.

3.7Polling Call

Polling means confirming if own station is within communicating range with other station. This function only provides affirmative or negative response; it does not provide position information. Note that simultaneous polling to more than one station is not possible.

1 Polling

2 Acknowledge

3 Polling

4 Acknowledge

3.7.1Sending a polling call

1.Press the CALL key. The display changes from standby display to the COMPOSE MESSAGE screen and the CALL TYPE is displayed in reverse video.

2.Press the ENT key to open the call type list.

3-25

Image 69

Sunpentown Intl FM-8800D/8800S manual Polling Call, Sending a polling call, Position Call

Contents

VHF Radiotelephone 00014993015 Example message Canceling Distress Alert Safety Instructions Important Notices Table of Contents DSC Operation for NON-DISTRESS Cases System Setup Foreword Word to FM-8800D/FM-8800S OwnersVii Features Program numberViii MAX System Configuration This page is intentionally left blank General SP-1 CH70 Watch Receiver SP-2 Operational Overview Controls Keys and LCD IndicationFront panel Push to Enter Controls ABC Shift Indications on the LCD 116 Auto Audio alarms VHF Basic Operation Turning the power on and adjusting contrastSelecting channel modes, channels Selecting channel modes Adjusting squelch Adjusting volume of loudspeakerSelecting output power Transmitting Dual watch Quick selection of CH16Scanning Remarks on voice communications LED warnings DSC Operational OverviewDSC operational overview Standby display When keyboard input is prohibited Distress alert transmission and output powerAutomatic acknowledge on/off Preparing and transmitting DSC messages Priority How to set priority of the remote station Distress Alert Transmission from the Distress Key DSC Distress CommunicationCall Type Distress Nature Undesignated Time to GO 4M 12S Cancel AlarmDistress ACK Press ENT Distress Alert Transmission with Nature of Distress NatureundesignatedDistress communication Undesignated Call Type DistressSimp TP Call Type Coast Call Distress Alert Transmission from Call KeyTo Coast AAA Routine Input Type Auto Canceling a False Distress Alert Procedure when in area A1 Vessel able Transmitting Dist ACK over CH16 Transmitting Dist ACK signal Press ENT to ACK DistressSimp TP Press Call to Send After transmitting Dist ACK Sending Distress Relay on Behalf of a Ship in Distress When you should relay a distress alertSending distress relay to coast station Coast ID Routine Coast ID Input Type AutoAuto Call Type Relay SEL Sending distress relay to all ships ID in Dist no Info Call Type Relay ALL Receiving Distress Relay Receiving distress relay all callCall Type Relay ALL Distress Relay ALL Receiving distress relay from coast station Press ENT This page is intentionally left blank General procedure for transmitting a coast or ship call DSC Operation for NON-DISTRESS CasesCoast or Ship Call Sending a coast or ship call Select CH Receiving acknowledgement of coast or ship call Time to GO 3M30 SCH no Info Able acknowledge call received Receiving a coast or ship callUnable acknowledge call received No response! Try calling again? Sending automatic acknowledge ACK BQ with comply status Able Coast ACK Coast ACK Routine Manually acknowledging individual call with Able Ship Call Manually acknowledging a coast or ship call with Unable Ship ACK Routine Group Call Busy Equip Disbld Mode Unavail CH UnavailSending a group call No Reason Press the ENTkeytoopen the calltypelist Press ENT Receiving a group call Sending a Pstn call Pstn Call Pstn call disconnection ship disconnects line Receiving a Pstn call Pstn call disconnection coast station disconnects line Sending an all ships call All Ships Call Select CH Press ENT to Change CH Receiving an all ships callCase of on Hook Case of OFF Hook Geographical Area Call Sending a geographical area callCall Type Area Call Select CH Receiving a geographical area call Position call requesting other ships position Position Call Cancel Alarm Position call other ship requests your position Automatic replyManual reply Polling Call Sending a polling callPosition Call Response is received+*. *!#$% Polling ACK Routine Receiving a polling call Polling Call Sending a neutral craft call Neutral Craft CallReceiving a neutral craft call Call Type Neutral Craft Sending a medical transport call Medical Transport Call Urgency Receiving a medical transport call Opening a log file Log FileShip ACK Ship Call Delete Received LOG Are YOU SURE? Yesno Answer This page is intentionally left blank Alarm Setup Basic SetupAlarm Old position alarm in manual position entry mode To set type of alarm to output Safety OFF Comply Status Able Auto ACK SetupUnable Reason No Reason Position Call on Polling Call on Able To set reason for unable To set position call responseTo set polling call response Erase LOG Menu Erasing LogsRcvd Ordinary Rcvd Distress Transmitted 01 CH Memory Channel Setup Auto ACK Erase LOG Memory Channel Message File Entry Message File EntryMessage File 1/13 Coast Call Group ID AreaShip ID Select CH #$#!% Print OUT Volume System Position SetupPosition Manual Print Out Setup Xmtd Call ManualRcvd Call Manual Daily Test Manual Earpiece Level Setup Volume SetupEarpiece volume EXT ENT Off-hook loudspeaker Intercom volume System Setup Displaying Self IDDisplaying Group ID List Naming Intercom Position Print OUT Volume Test System Group ID List Intercom Naming Program Version Displaying Program Version This page is intentionally left blank Maintenance Maintenance & TroubleshootingTroubleshooting When the power cannot be turned on Daily Test TX Power TX/RX PCBCPU PCB CH70 RX PCB OK Error Message Parts LocationTransceiver unit FM-8800D/8800S Remote station RB-8800/RB-8810/RB-8810-W/HS-8800/HS-8800-W Handset HS-2003Junction box IF-8810 DMC Interface IF-8820 Appendix Menu TreeAP-1 Appendix AP-2 AP-3 Marine VHF Channel Lists AP-4 AP-5 AP-6 Private Channels AP-7 AP-8 157.500 AP-9 AP-10 AP-11 AP-12 AP-13 Input sentences Digital Interface IEC 61162-1 EditionLoad requirements as listner Output sentence GGA -Global positioningsystem GPS fixdata AP-15 AP-16 GNS-GNSS fixed data AP-17 RMC Recommemded minimum specific GPS/TRANSIT data AP-18 TLL Target latitude and longitude Thermal Printer UTP-80FK Specifications, Parts of the PrinterPrinter usage cautions Paper usage cautions AP-20 OperationParts Loading roll paper Front panel AP-21 AP-22 Setting the DIP switch AP-23 Printing testRemedy for paper jam AP-24 Adjusting printing intensity Thermal Printer UTP-58E Paper replacementUTP-58E for RC-8800S/D-B Rack Console and PP-8800A Printer AP-25 AP-26 IN-1 Index IN-2 0560