Appendix C System Speciﬁcations | SUPER MICRO Computer 6015W-NT

Appendix C: System Speciﬁ cations

Appendix C

System Speciﬁcations

Processors

Single or dual Intel® Xeon® 5400/5300LV/5200/5100LV Sequence processors at a front side (system) bus speed of 1600/1333/1066 MHz.

Note: Please refer to our web site for a complete listing of supported processors.

Chipset

Intel 5400/ESB2 chipset

BIOS

8 Mb Phoenix® Flash ROM

Memory Capacity

Eight 240-pin DIMM sockets supporting up to 64 GB of ECC FBD DDR2- 800/667/533 SDRAM.

See the memory section in Chapter 5 for details.

SATA Controller

Intel ESB2 on-chip controller for six-port Serial ATA (RAID 0, 1 5 and 10 supported)

SATA Drive Bays

6015W-NTR/6015W-NT:

Four (4) hot-swap drive bays to house four (4) SATA drives

6015W-UR/6015W-U:

Four (4) hot-swap drive bays to house four (4) SAS/SATA drives (with optional UIO SAS controller card)

Peripheral Drive Bays

One (1) slim ﬂ oppy drive (optional)

One (1) slim DVD-ROM drive

C-1

Image 107

SUPER MICRO Computer 6015W-UR, 6015W-NTR user manual Appendix C System Speciﬁcations, Processors

Contents

Super Manual Revision 1.0a Release Date April 23 Manual Organization PrefaceAbout This Manual System Safety Preface Table of Contents System Interface Bios Overview Chapter Introduction Serverboard Features Server Chassis Features Cooling System Front Control PanelBackplane CPU1 CPU2 Asia-Paciﬁc Contacting SupermicroHeadquarters Europe Unpacking the System Chapter Server InstallationPreparing for Setup Server Precautions Choosing a Setup LocationRack Precautions Rack Mounting Considerations Ambient Operating Temperature Identifying the Sections of the Rack Rails Installing the System into a RackInstalling the Inner Rails Installing the Rack Rails Installing the Outer Rails Installing the Server into a Rack Installing the Server into the Rack Installing the Server into a Telco Rack Installing the Server into a Telco Rack Checking the Components Checking the Serverboard SetupAccessing the Inside of the System Checking the Drives Checking the Drive Bay Setup Checking the Airﬂow Providing Power Control Panel Buttons ResetChapter System Interface Universal Information LED PowerControl Panel LEDs NIC2 Sata Drive Carrier LEDs Electrical Safety Precautions Chapter System Safety General Safety Precautions ESD Precautions Installing the Onboard Battery Operating Precautions Unpacking Chapter Advanced Serverboard SetupPrecautions Handling the Serverboard Installing the Processor Processor and Heatsink InstallationPage Removing the Heatsink Installing the Heatsink Connecting the Control Panel Connecting CablesConnecting Data Cables Connecting Power Cables I/O Ports Front Control Panel Header Pins JF1 Memory Support Installing MemoryInstalling DIMMs Installing Dimm into Slot PCI Slot/Card Conﬁgurations PCI Card InstallationAdding PCI Cards PCI Expansion Slots Super X7DWU Layout Serverboard Details X7DWU Quick Reference Jumper Description Default Setting Connector Deﬁnitions Universal Information LED HDD LED Universal Serial Bus USB0/1 Power Fail LEDReset Button Power Button Fan Headers Universal Serial Bus HeadersSerial Ports Wake-On-LAN Power LED/SpeakerATX PS/2 Keyboard and PS/2 Mouse Ports Overheat LED LAN1/2 Ethernet Ports Wake-On-Ring Explanation of Jumpers Jumper Settings Cmos Clear VGA Enable/DisablePower Force On LAN Enable/Disable Memory Voltage Select Watch Dog Enable/DisableI2C Enable/Disable LAN1/LAN2 LEDs Onboard Indicators Floppy, IDE and Sata Drive Connections Floppy Connector Sata Ports IDE Connector Driver Installation Display Screen Installing Drivers Static-Sensitive Devices Chapter Advanced Chassis Setup Chassis Front and Rear Views Control Panel Replacing System Fans System FansSystem Fan Failure Removing the Front Bezel Drive Bay Installation/Removal Removing the Front Bezel Accessing the Drive Bays Mounting a Sata Drive in a Drive Carrier Sata Drive Installation Removing a Sata Drive from the Server Installing/Removing a Sata Drive Removing the Chassis Cover DVD-ROM and Floppy Drive InstallationRemoving/Installing a Drive 6015W-UR/6015W-NTR Power SupplyReplacing the Power Supply 6015W-U/6015W-NT Removing/Replacing the Power Supply Page Introduction Chapter Press the Delete key to enter Setup Running SetupMain Bios Setup Default settings are in bold text unless otherwise noted System Date Main Bios Setup Menu Main Setup FeaturesBios Date System Time CHS Format IDE Channel 0 Master/Slave and Secondary IDE Master/ SlaveType LBA Format LBA Mode ControlTransfer Mode Ultra DMA Mode Sata Ahci Available when Sata RAID is Disabled Native Mode OperationSerial ATA Sata RAID Enable ICH RAID Code Base Available when Sata RAID is Enabled QuietBoot Mode Advanced SetupBoot Features QuickBoot Mode Set Power On Password Acpi ModePower Button Behavior EFI OS Boot Memory Cache PCI Conﬁguration Advanced Chipset Control 4GB PCI Hole Granularity Memory Branch ModeIntel VT for Directed I/O Memory Voltage AMB Thermal Sensor High Temperature Dram OperationEnhanced x8 Detection Demand Scrubbing Advanced Processor Options Direct Cache Access Available when supported by the CPU C1/C2 Enhanced Mode Available when supported by the CPUExecute Disable Bit Available when supported by the CPU Hardware Prefetcher Available when supported by the CPU Device Conﬁguration DMI Event Logging Hardware Monitor Logic Console Redirection Voltage Monitoring Fan Speed Control Modes Timer for Loading OS Minutes Abled Bios Post ErrorsAbled Bios Post Watch Dog OS Boot Watch Dog Realtime Sensor Data System Event Log/System Event Log List Mode Security Supervisor Password IsUser Password Is Set Supervisor Password Current TPM State Set User PasswordPassword on Boot TPM Trusted Platform Modules Support Boot Priority Order/Excluded from Boot Orders Boot Exit Page Appendix a Bios Post Messages Check date and time settings System Cmos checksum bad Default conﬁguration usedSystem timer error Real time clock error Entering Setup System cache error Cache disabledFail-Safe Timer NMI Failed Allocation Error for device Device IRQ conﬂict PS/2 Mouse Boot Summary ScreenFixed Disk n Invalid System Conﬁguration Data Video Bios shadowed Press F1 to resume, F2 to Setup, F3 for previousPress F2 to enter Setup System Bios shadowedPage Terminal Post Errors Appendix B Bios Post CodesRecoverable Post Errors RAM failure on data bits xxxx* of low byte of memory bus Post Code Description Inform RomPilot about the end of Post optional Following are for boot block in Flash ROM Page Processors Appendix C System Speciﬁcations Expansion Slots see -6 for details Chassis Operating Environment