Accessing the Drive Bays | SUPER MICRO Computer 6015W-NTR, 6015W-UR

Chapter 6: Advanced Chassis Setup

Figure 6-3. Removing the Front Bezel

1. Unlock

2. Press release knob

3. Remove bezel assembly

Accessing the Drive Bays

SATA Drives: Because of their hotswap capability, you do not need to access the inside of the chassis or power down the system to install or replace SATA drives. Proceed to the next section for instructions.

DVD-ROM/Floppy Disk Drives: For installing/removing a DVD-ROM or ﬂ oppy disk drive, you will need to gain access to the inside of the 6015W-UR/6015W-U/6015W- NTR/6015W-NT by removing the top cover of the chassis. Proceed to the "DVD- ROM and Floppy Drive Installation" section later in this chapter for instructions.

Note: Only "slim" DVD-ROM and ﬂ oppy drives will ﬁ t into the 6015W-UR/6015W- U/6015W-NTR/6015W-NT.

6-5

Image 61

SUPER MICRO Computer 6015W-NTR, 6015W-UR user manual Accessing the Drive Bays, Removing the Front Bezel

Contents

Super Manual Revision 1.0a Release Date April 23 About This Manual PrefaceManual Organization System Safety Preface Table of Contents System Interface Bios Overview Chapter Introduction Serverboard Features Server Chassis Features Backplane Front Control PanelCooling System CPU1 CPU2 Headquarters Contacting SupermicroEurope Asia-Paciﬁc Preparing for Setup Chapter Server InstallationUnpacking the System Rack Precautions Choosing a Setup LocationServer Precautions Rack Mounting Considerations Ambient Operating Temperature Installing the Inner Rails Installing the System into a RackIdentifying the Sections of the Rack Rails Installing the Rack Rails Installing the Outer Rails Installing the Server into a Rack Installing the Server into the Rack Installing the Server into a Telco Rack Installing the Server into a Telco Rack Accessing the Inside of the System Checking the Serverboard SetupChecking the Components Checking the Drives Checking the Drive Bay Setup Checking the Airﬂow Providing Power Chapter System Interface ResetControl Panel Buttons Control Panel LEDs PowerUniversal Information LED NIC2 Sata Drive Carrier LEDs Electrical Safety Precautions Chapter System Safety General Safety Precautions ESD Precautions Installing the Onboard Battery Operating Precautions Precautions Chapter Advanced Serverboard SetupHandling the Serverboard Unpacking Installing the Processor Processor and Heatsink InstallationPage Removing the Heatsink Installing the Heatsink Connecting Data Cables Connecting CablesConnecting Power Cables Connecting the Control Panel I/O Ports Front Control Panel Header Pins JF1 Installing DIMMs Installing MemoryMemory Support Installing Dimm into Slot Adding PCI Cards PCI Card InstallationPCI Expansion Slots PCI Slot/Card Conﬁgurations Super X7DWU Layout Serverboard Details X7DWU Quick Reference Jumper Description Default Setting Connector Deﬁnitions Universal Information LED HDD LED Reset Button Power Fail LEDPower Button Universal Serial Bus USB0/1 Serial Ports Universal Serial Bus HeadersFan Headers ATX PS/2 Keyboard and PS/2 Mouse Ports Power LED/SpeakerOverheat LED Wake-On-LAN LAN1/2 Ethernet Ports Wake-On-Ring Explanation of Jumpers Jumper Settings Power Force On VGA Enable/DisableLAN Enable/Disable Cmos Clear I2C Enable/Disable Watch Dog Enable/DisableMemory Voltage Select LAN1/LAN2 LEDs Onboard Indicators Floppy, IDE and Sata Drive Connections Floppy Connector Sata Ports IDE Connector Driver Installation Display Screen Installing Drivers Static-Sensitive Devices Chapter Advanced Chassis Setup Chassis Front and Rear Views Control Panel System Fan Failure System FansReplacing System Fans Removing the Front Bezel Drive Bay Installation/Removal Removing the Front Bezel Accessing the Drive Bays Mounting a Sata Drive in a Drive Carrier Sata Drive Installation Removing a Sata Drive from the Server Installing/Removing a Sata Drive Removing/Installing a Drive DVD-ROM and Floppy Drive InstallationRemoving the Chassis Cover Replacing the Power Supply Power Supply6015W-UR/6015W-NTR 6015W-U/6015W-NT Removing/Replacing the Power Supply Page Introduction Chapter Main Bios Setup Running SetupDefault settings are in bold text unless otherwise noted Press the Delete key to enter Setup Bios Date Main Bios Setup Menu Main Setup FeaturesSystem Time System Date Type IDE Channel 0 Master/Slave and Secondary IDE Master/ SlaveCHS Format Transfer Mode LBA Mode ControlUltra DMA Mode LBA Format Serial ATA Sata RAID Enable Native Mode OperationICH RAID Code Base Available when Sata RAID is Enabled Sata Ahci Available when Sata RAID is Disabled Boot Features Advanced SetupQuickBoot Mode QuietBoot Mode Power Button Behavior Acpi ModeEFI OS Boot Set Power On Password Memory Cache PCI Conﬁguration Advanced Chipset Control Intel VT for Directed I/O Memory Branch ModeMemory Voltage 4GB PCI Hole Granularity Enhanced x8 Detection High Temperature Dram OperationDemand Scrubbing AMB Thermal Sensor Advanced Processor Options Execute Disable Bit Available when supported by the CPU C1/C2 Enhanced Mode Available when supported by the CPUHardware Prefetcher Available when supported by the CPU Direct Cache Access Available when supported by the CPU Device Conﬁguration DMI Event Logging Hardware Monitor Logic Console Redirection Voltage Monitoring Fan Speed Control Modes Abled Bios Post Watch Dog Abled Bios Post ErrorsOS Boot Watch Dog Timer for Loading OS Minutes Realtime Sensor Data System Event Log/System Event Log List Mode User Password Is Supervisor Password IsSet Supervisor Password Security Password on Boot Set User PasswordTPM Trusted Platform Modules Support Current TPM State Boot Priority Order/Excluded from Boot Orders Boot Exit Page Appendix a Bios Post Messages System timer error System Cmos checksum bad Default conﬁguration usedReal time clock error Check date and time settings Fail-Safe Timer NMI Failed System cache error Cache disabledAllocation Error for device Entering Setup Fixed Disk n PS/2 Mouse Boot Summary ScreenInvalid System Conﬁguration Data Device IRQ conﬂict Press F2 to enter Setup Press F1 to resume, F2 to Setup, F3 for previousSystem Bios shadowed Video Bios shadowedPage Recoverable Post Errors Appendix B Bios Post CodesTerminal Post Errors RAM failure on data bits xxxx* of low byte of memory bus Post Code Description Inform RomPilot about the end of Post optional Following are for boot block in Flash ROM Page Processors Appendix C System Speciﬁcations Expansion Slots see -6 for details Chassis Operating Environment