Manuals / Tamron / Home Audio / Satellite Radio

Tamron IC-R10 Accessory attachment, Antenna, Belt clip, Handstrap, Ni-CdBATTERIES AND ACCESSORIES

Models: IC-R10

1 84

Download 84 pages 30.38 Kb

Page 14

Image 14

2 Ni-Cd BATTERIES AND ACCESSORIES

■Accessory attachment

Antenna

Insert the supplied antenna into the antenna connector and rotate the an- tenna as shown in the diagram below. Keep the jack cover attached when jacks are not in use to avoid bad contacts.

Belt clip

Attach the belt clip using the supplied screws.

Conveniently attaches to your belt.

Handstrap

Attach the handstrap as shown in the diagram below. Facilities carrying.

Page 14

Image 14

Tamron IC-R10 instruction manual Accessory attachment, Antenna, Belt clip, Handstrap, Ni-CdBATTERIES AND ACCESSORIES

Contents

iR10 COMMUNICATIONS RECEIVERREAD ALL INSTRUCTIONS CAREFULLY be EXPLICIT DEFINITIONSCAUTIONS For U.S.A. only UNPACKINGq w e t r TABLE OF CONTENTS TABLE OF CONTENTS OPERATING THEORYOPERATING NOTES 1 PANEL DESCRIPTION Front and side panelsTop panel PANEL DESCRIPTION1 PANEL DESCRIPTION Function displayMEMO VFO EASY VSC AT T WFM A M LSB USB C W AF C q SLEEP TIMER INDICATOR PANEL DESCRIPTIONPRIMARY FUNCTION Keypad1 PANEL DESCRIPTION PRIMARY FUNCTION SECONDARY FUNCTION while pushing FUNCCharging Ni-Cdbatteries 2 Ni-CdBATTERIES AND ACCESSORIESCharging precautions About Ni-CdbatteriesNi-CdBATTERIES AND ACCESSORIES Battery installationCharging connections Belt clip Accessory attachmentAntenna HandstrapBASIC OPERATION 1. Turn power ON2. Adjust the volume General4. Select VFO mode 3. Adjust the squelch3-1.Adjust the RF gain What is squelch?WFM VFO144.0000 Selecting a receive mode144.0000 A M144.00002. Select the tuning step Selecting a tuning step1.Call up the tuning step set mode What are tuning steps?2. Enter the frequency Tuning a frequency via the keypad1. Select the frequency BASIC OPERATION2. Tune a frequency Tuning a frequency via the dial1.Select VFO mode and a receive mode 3 BASIC OPERATION144.0000 Dial select steps144.0000 DIAL SEL 144.0000What is the band scope function? Band scope functionPreparation 3 BASIC OPERATIONBASIC OPERATION Set band scope functionsignal lower freq. higher freq displayed freq6. Select the tuning step 3. Adjust volume4. Adjust squelch 2. Select VFOExample 59.25 MHz 8. Use the tuning dialExample 59.75 MHz 7. Tune the station3. Adjust volume TS 25.00kHz1. Turn power ON 4. Adjust squelch8. Use the tuning dial Example 118.00 MHz Example 118.925 MHz118.9500 7. Tune the stationSelect MEMORY mode 4 MEMORY MODESelecting MEMORY mode What is memory mode?Selecting a memory channel-1 Selecting a BANK and memory channelSelecting a BANK channel Selecting a memory channel-2Programming a memory channel 1.BANK and memory channel setting2.Setting other information 3. Programming3.BANK and memory channel setting 1.Setting receive conditions2.BANK and memory channel setting 4. Programming3. Programming details 1. Set up2. BANK and memory channel setting Programming a memory channelMEMORY MODE 3. Programming details - cont3. Programming details - cont 1.BANK and memory channel setting 2. Data setting3. Programming the data 4 MEMORY MODESET CH NO 1. Setting the frequency2.Set the BANK and memory channel A45 BLANKF01 E F01 BLANKSET CH NAME 1. Setting the frequencyMODE:AM 3.Programming details - contSET MODE 121.5000Copy to the other memory channel Memory copyCopy to VFO mode What is the memory copy function?118.0250 MHz, AM, B07 to F02 Copying example59.7500 MHz, WFM, A45 to VFO MEMORY COPYGeneral 5 SCANNING OPERATIONWhat is scanning? Scan typesAUTO-MEMORYWRITE SCAN SCANNING OPERATIONPROGRAM SCAN BANK SCAN1. Set receive mode 2.Set the volume and squelch levelsBefore scanning 5 SCANNING OPERATIONWhat is VSC? Set the scan delaySet the VSC What is scan delay?Start and stop the scan Full scanMemory scan Start and stop the scan1. Select program scan channel Program scan2. Start and stop scanning SCANNING OPERATION1. Select program scan channel Auto memory write scan2. Start and stop scanning 144.0000For your convenience SCANNING OPERATIONDuring auto-memorywrite scanning 2. Start and stop scanning BANK scan1. Select BANK scan and BANK number 5 SCANNING OPERATION2. Start and stop scanning Mode select scan1. Select mode select scan and mode SCANNING OPERATION1. Memory skip setting 1. Program skip setting2.Program skip setting - cont Skip functionSIGNAVI SIGNAVI function1. Set SIGNAVI function 2.Select scan type and start scanningGeneral 6 PRIORITY WATCHWhat is priority watch? VFO FREQUENCY WATCHMEMORY SCAN/BANK SCAN/MODE SELECT SCAN WATCH A01A32PRIORITY WATCH 59.7500 1. Program a priority channel2. Set MAIN frequency F011. Select EASY mode EASY MODEEASY mode operation 2.Select frequency range and start scanningGeneral 8 EDIT FUNCTIONMemory channel edit SET CH NAME Memory channel edit ﬂow chart1 Push for 2 sec 2 Fixed contents will be cleared EDIT FUNCTIONSET FREQ 1.Enter memory edit mode2. Set frequency 3. Set channel names5.Set attenuator condition 4.Set receive mode and skip conditionMODE FM 6. Set BANK names8 EDIT FUNCTION Program scan channel editEASY mode channel edit 1 Push for 2 sec 2 Fixed contents will be cleared START FREQTS 5.00kHz 144.00002. Set channel names Program scan or EASY mode channel edit1. Enter edit mode 3. Set start frequencySCAN DELAY 5.Set receive mode and tuning step6. Set scan delay time 4. Set end frequency9 SET MODE GeneralBeep audio Entering SET modeOpening message Display contrastcondition Power saveBacklight Program skipCI-Vbaud Scan delayCI-Vaddress CI-Vtransceive10 OTHER FUNCTIONS Low battery indicatorSetting AFC AFC functionSet monitor Monitor functionLock function Set lockSet ATT ATT functionNB/ANL function Set NB/ANLSet sleep timer Sleep timer functionUser TS setting Set tuning stepNAME SEARCH Memory search functionEnter memory search mode Enter memory channel nameswhen matching channel is found SearchingSelecting a memory channel when no match is foundSet auto TS Auto mode and TS functionSet auto mode TS AUTOAll reset Resetting the CPUPartial reset PARTIAL RESETCLONE MODE Data cloningSet cloning mode and start cloning 10 OTHER FUNCTIONSCorresponding Alphanumeric Character ALPHANUMERIC KEY ASSIGNMENTKeypad InputData format 12 CONTROL COMMANDSCommand table GeneralCI-Vconnection example CONTROL COMMANDSCT-17 13 TROUBLESHOOTING TROUBLESHOOTING RECEIVER 14 SPECIFICATIONSGENERAL OPTIONS Copyright 1996 by Icom Inc 6-9-16Kamihigashi, Hirano-ku,Osaka 547 JapanA-5410H-1EX-t