Teledyne 200AH 9.1.6. Factory Calibration Procedure

Teledyne API Model 200AH NOX Analyzer Instruction Manual, 06492, Rev. G2

9-20

Table 9-6: Test Channel Readings (Continued)

TEST Channel Minimum* Maximum* Description

RCELL TEMP 0C 70C Reaction Cell temperature is set to 50C. At the

setpoint, a typical reading is 3600 mV.

BLOCK TEMP 0C 70C The Block temperature is set to 50C. At the

setpoint, a typical reading is 3600 mV.

IZS TEMP 0C 70C The IZS temperature is set to 50C. At the

setpoint, a typical reading is 3600 mV.

CONV TEMP 0C 1000C The Converter temperature is 315C. At the

setpoint, a typical voltage is 3150 mV.

PMT TEMP 0C 70C The PMT temperature is unique in that the

voltage is inverse to the temperature. A typical

reading for 8C would be 4200 mV.

CHASSIS

TEMP 0C 70C The Chassis (Box) temperature is variable due

to variable ambient air temperature. The Box

temp generally runs about 5C above the

surrounding air temp. Thus in a 25C room, the

Box temp would be about 30C and have a

TEST channel voltage of about 2000 mV.

DCPS

VOLTAGE 0 mV 5000 mV The DCPS is a composite of several DC power

supply voltages in the instrument. It has been

arbitrarily set at 2500 mV, which is typical.

HVPS

VOLTAGE 0 V 5000 V The HVPS voltage is a scaled up reading of the

programming voltage going to the HVPS. Zero

to 1000mV corresponds 0-1000 VDC for the

HVPS, which is the maximum voltage possible.

A typical reading would be 700 mV

corresponding to 700 VDC for the HVPS.

*Minimum and Maximum readings depend on the DAC 3 switch settings of the V/F board. For the

standard 5VDC range, minimum corresponds to 0VDC and maximum corresponds to 5VDC.

9.1.6. Factory Calibration Procedure

The Factory Cal procedure balances the PMT, preamp, and software gain factors so the

instrument has optimum noise, linearity, and dynamic range. It should be used in the cases where

you were unable to zero or span the instrument or slope and offset values were outside of the

acceptable range and other more obvious reasons for problems have been eliminated.

Contents

Main INSTRUCTION MANUAL MODEL 200AH NITROGEN OXIDES ANALYZER Page SAFETY MESSAGES Page Table of Contents 3. SPECIFICATIONS, WARRANTY.................................................................. 3-1 4. THE M200AH NOX ANALYZER................................................................... 4-1 6. OPTIONAL HARDWARE AND SOFTWARE................................................ 6-1 7. CALIBRATION AND ZERO/SPAN CHECKS ...............................................7-1 9. TROUBLESHOOTING AND ADJUSTMENTS.............................................. 9-1 Page Teledyne API Model 200AH NOX Analyzer Instruction Manual, 06492, Rev. G2 vii LIST OF FIGURES Teledyne API Model 200AH NOX Analyzer Instruction Manual, 06492, Rev. G2 viii LIST OF TABLES Page Page 1. HOW TO USE THIS MANUAL Page 2. GETTING STARTED 2.1. Unpacking 2.2. Electrical and Pneumatic Connections Page Page Page Page Page 2.3. Initial Operation Teledyne API Model 200AH NOX Analyzer Instruction Manual, 06492, Rev. G2 2-8 Teledyne API Model 200AH NOX Analyzer Instruction Manual, 06492, Rev. G2 2-9 Step 2 - Calibrate the instrument for NOX: Zero/Span Calibration Procedure Teledyne API Model 200AH NOX Analyzer Instruction Manual, 06492, Rev. G2 2-10 Zero/Span Calibration Procedure (Continued) Teledyne API Model 200AH NOX Analyzer Instruction Manual, 06492, Rev. G2 2-11 Step 3 - Review Quality of calibration: Calibration Quality Check Procedure Step 4 - The M200AH is now ready to measure sample gas. Page Page Page Teledyne API Model 200AH NOX Analyzer Instruction Manual, 06492, Rev. G2 2-15 Table 2-1: Final Test and Calibration Values (table continued) Teledyne API Model 200AH NOX Analyzer Instruction Manual, 06492, Rev. G2 2-16 Table 2-1: Final Test and Calibration Values (Continued) Teledyne API Model 200AH NOX Analyzer Instruction Manual, 06492, Rev. G2 3-1 3. SPECIFICATIONS, WARRANTY 3.1. Specifications NOX Specifications O2 Option 3.2. Warranty 4. THE M200AH NOX ANALYZER 4.1. Principle of Operation 4.1.1. NOX Measurement hv NO * NO 4.1.2. Oxygen Measurement (Option) Page Page 4.2. Operation Summary 4.2.1. NOX Sensor Module, Reaction Cell, Detector 4.2.2. Oxygen Sensor Module (Option) 4.2.3. Pneumatic Sensor Board 4.2.4. Computer Hardware and Software 4.2.5. V/F Board 4.2.6. Front Panel 4.2.7. Power Supply Module 4.2.8. Pump, Valves, Pneumatic System Page Page 4.2.9. Ozone Generator 4.2.10. NO2 - NO Converter Page 5. SOFTWARE FEATURES 5.1. Index to Front Panel Menus Page Page Page Page Teledyne API Model 200AH NOX Analyzer Instruction Manual, 06492, Rev. G2 5-6 5.1.1. Sample Menu Table 5-1: M200AH Sample Menu Structure Teledyne API Model 200AH NOX Analyzer Instruction Manual, 06492, Rev. G2 5-7 5.1.2. Set-Up Menu Table 5-2: M200AH Setup Menu Teledyne API Model 200AH NOX Analyzer Instruction Manual, 06492, Rev. G2 5-8 Table 5-2: M200AH Setup Menu (Continued) Teledyne API Model 200AH NOX Analyzer Instruction Manual, 06492, Rev. G2 5-9 Table 5-3: M200AH Setup Menu Teledyne API Model 200AH NOX Analyzer Instruction Manual, 06492, Rev. G2 5-10 Table 5-4: M200AH Setup Menu 5.2. Sample Mode 5.2.1. Test Functions Page Page Page 5.2.2. CAL, CALS, CALZ, Calibration Functions Page 5.3. Set-Up Mode 5.3.1. Configuration Information (CFG) 5.3.2. Automatic Calibration (AutoCal) 5.3.3. Data Acquisition System (DAS) Page 5.3.4. Range Menu Page Page 5.3.5. Password Enable 5.3.6. Time of Day Clock 5.3.7. Diagnostic Mode Page 5.4. M200AH Operating Modes 5.4.1. NO/NOx/NO2 Switching Mode 5.4.2. NOX Only Mode 5.4.3. NO Only Mode 5.5. 4-20 mA Current Loop 5.6. Status Output 5.7. RS-232 Interface 5.7.1. Setting up the RS-232 Interface Page Page 5.7.2. Command Summary Teledyne API Model 200AH NOX Analyzer Instruction Manual, 06492, Rev. G2 5-32 Table 5-12: RS-232 Command Summary Page Page Teledyne API Model 200AH NOX Analyzer Instruction Manual, 06492, Rev. G2 5-35 5.7.3. TEST Commands and Messages Table 5-15: RS-232 Test Messages 5.7.4. WARNING Commands and Messages 5.7.5. CALIBRATION Commands and Messages 5.7.6. DIAGNOSTIC Commands and Messages 5.7.7. DAS Commands and Messages Page 5.7.8. VARIABLES Commands and Messages Page 6. OPTIONAL HARDWARE AND SOFTWARE 6.1. Rack Mount Options 6.2. Zero/Span Valves Option Teledyne API Model 200AH NOX Analyzer Instruction Manual, 06492, Rev. G2 6-3 6.2.1. Autocal - Setup Zero/Span Valves Teledyne API Model 200AH NOX Analyzer Instruction Manual, 06492, Rev. G2 6-4 Table 6-3: Action of MODE Field in AutoCal 6.3. Oxygen Sensor Option 6.4. Isolated 4-20 mA Current Loop Option 6.5. Molybdenum Converter Option 6.6. External Desiccant Canister Option 6.7. Alternate Bypass Flow Orifice Option 6.8. M501 External Converter Option Page 7. CALIBRATION AND ZERO/SPAN CHECKS Teledyne API Model 200AH NOX Analyzer Instruction Manual, 06492, Rev. G2 7-2 Table 7-1: Types of Zero/Span Check and Calibration 7.1. Manual NOX Zero/Span Check or Cal With Zero/Span Gas in the Sample Port Page Teledyne API Model 200AH NOX Analyzer Instruction Manual, 06492, Rev. G2 7-5 Table 7-4: Manual Span Calibration Procedure - Span Gas Thru Sample Port 7.2. Manual O2 Zero/Span Check or Cal With Zero/Span Gas in the Sample Port 7.3. Manual Zero/Span Check with Zero/Span Valves Option Page 7.4. Dynamic Zero/Span Calibration Using AutoCal 7.5. Use of Zero/Span Valves with Remote Contact Closure 7.6. NO Only Mode Calibration 7.7. NOX Only Mode Calibration 7.8. Calibration Requirements for AutoRange or Remote Range 7.9. Calibration Requirements for Independent Range 7.10. Calibration Quality 7.11. Converter Efficiency Compensation 7.12. Recommendations for CEM Applications 7.12.1. Calibration Gasses 7.12.2. Calibration Frequency 7.12.3. Converter Efficiency Page 8. MAINTENANCE 8.1. Maintenance Schedule 8.2. Replacing the Sample Particulate Filter Page 8.3. Replacing the Converter Page 8.4. Cleaning the Reaction Cell Page Page 8.5. Pneumatic Line Inspection Page Page Page 8.6. Leak Check Procedure 8.7. Light Leak Check Procedure 8.8. Prom Replacement Procedure 9. TROUBLESHOOTING AND ADJUSTMENTS 9.1. Operation Verification - Diagnostic Techniques 9.1.1. Fault Diagnosis with TEST Variables Teledyne API Model 200AH NOX Analyzer Instruction Manual, 06492, Rev. G2 9-3 Teledyne API Model 200AH NOX Analyzer Instruction Manual, 06492, Rev. G2 9-4 Table 9-1: Test Functions (Continued) Teledyne API Model 200AH NOX Analyzer Instruction Manual, 06492, Rev. G2 9-5 Table 9-1: Test Functions (Continued) Teledyne API Model 200AH NOX Analyzer Instruction Manual, 06492, Rev. G2 9-6 Table 9-1: Test Functions (Continued) Test Function Factory Set-Up Comment Teledyne API Model 200AH NOX Analyzer Instruction Manual, 06492, Rev. G2 9-7 Table 9-1: Test Functions (Continued) Test Function Factory Set-Up Comment 9.1.2. Fault Diagnosis with WARNING Messages Teledyne API Model 200AH NOX Analyzer Instruction Manual, 06492, Rev. G2 9-9 Table 9-2: Front Panel Warning Messages 9.1.3. Fault Diagnosis using DIAGNOSTIC Mode Teledyne API Model 200AH NOX Analyzer Instruction Manual, 06492, Rev. G2 9-11 Table 9-3: Summary of Diagnostic Modes Teledyne API Model 200AH NOX Analyzer Instruction Manual, 06492, Rev. G2 9-12 9.1.3.1. Signal I/O Diagnostics Table 9-4: Diagnostic Mode - Signal I/O Teledyne API Model 200AH NOX Analyzer Instruction Manual, 06492, Rev. G2 9-13 Table 9-4: Diagnostic Mode - Signal I/O (Continued) Teledyne API Model 200AH NOX Analyzer Instruction Manual, 06492, Rev. G2 9-14 Table 9-4: Diagnostic Mode - Signal I/O (Continued) Teledyne API Model 200AH NOX Analyzer Instruction Manual, 06492, Rev. G2 9-15 Table 9-4: Diagnostic Mode - Signal I/O (Continued) Page 9.1.4. M200AH Internal Variables Teledyne API Model 200AH NOX Analyzer Instruction Manual, 06492, Rev. G2 9-18 Table 9-5: Model 200AH Variables Teledyne API Model 200AH NOX Analyzer Instruction Manual, 06492, Rev. G2 9-19 9.1.5. Test Channel Analog Output 9.1.6. Factory Calibration Procedure Page Page Page 9.2. Performance Problems 9.2.1. AC Power Check 9.2.2. Flow Check 9.2.3. No Response to Sample Gas 9.2.4. Negative Output 9.2.5. Excessive Noise 9.2.6. Unstable Span 9.2.7. Unstable Zero 9.2.8. Inability to Span 9.2.9. Inability to Zero 9.2.10. Non-Linear Response 9.2.11. Slow Response 9.2.12. Analog Output Doesn't Agree With Display Concentration 9.3. Subsystem Troubleshooting and Adjustments 9.3.1. Computer, Display, Keyboard Page Page 9.3.2. RS-232 Communications Page Page 9.3.3. Voltage/Frequency (V/F) Board Page Page Page Page Page 9.3.4. Status/Temp Board Page 9.3.5. Power Supply Module Teledyne API Model 200AH NOX Analyzer Instruction Manual, 06492, Rev. G2 9-46 Table 9-9: Power Supply Module Subassemblies Page Page 9.3.6. Ozone Generator Page Page Page 9.3.7. Flow/Pressure Sensor Page Page Page Page 9.3.8. NOX Sensor Module Page Page Page Page 9.3.9. Z/S Valves 9.3.10. Pneumatic System Teledyne API Model 200AH NOX Analyzer Instruction Manual, 06492, Rev. G2 A-1 APPENDIX A ELECTRICAL SCHEMATICS Table A-1: Electrical Schematics Page APPENDIX B SPARE PARTS AND EXPENDABLES Page Page SPARE PARTS LIST LEVEL 1 SPARES KIT (WITH MINI-HICON CONVERTER) LEVEL 1 SPARES KIT (WITH MOLYBDENUM CONVERTER)