Teledyne powerpod 400 10.0 Setup/Cal Mode

164-122012 PowerPOD 400 Page 19 of 42

10.1. ENTERING THE SETUP/CAL MODE

Pressing the MODE key causes the MODE menu to be displayed. Choose the SETUP/CAL mode by

pressing the number “3” key then ENTER. A CHANNEL SELECT menu is presented on the display.

It should be noted that, although the user must select a specific channel number, some choices in the

following menus may affect the operation of all channels and/or the display (ex; Display Brightness, type of

communication). See the following menu options for more details.

10.2. DISPLAY SETUP

After entering the SETUP/CAL mode and selecting a channel number as described in the previous

section, several selections are available that will affect the display. Follow the steps below to gain the

desired customized display.

10.2.1. Blanking a Display Line/Channel

Use the serial command “DndCr”, where

n = channel number,

d = 1 for Totalizer Mode,

2 for Meter Mode,

3 for a blanked line and

Cr = carriage return.

10.2.2. Selecting Display Brightness

While the SETUP/CAL menu is displayed, choose DISPLAY by pressing the keys “1” + ENTER.

Choose BRIGHTNESS by pressing the number “1” key + ENTER. The BRIGHTNESS menu will be

visible. One of four different brightness levels can be chosen by pressing a number key. The number “1”

key selects the dimmest setting while the number “4” key selects the brightest. Any change in brightness

will affect the entire display after pressing the ENTER key.

10.0 Setup/Cal Mode

Note: Front panel lockout and display line (channel) blanking are only available

through serial communication.

Contents

Main Manual Print History Visit www.teledyne-hi.com for WEEE disposal guidance. Table of Contents Page 1.0 Quick Start Instructions P 2.0 Safety 3.0 Features Page 4.0 Specifications PowerPod-400 Specifications Table 5.0 Front Panel 7 P ower 1 4 0 9 3 6 8 6.0 Rear Panel 7.1. POWER 7.2. COMMUNICATIONS 7.0 Wiring 7.3. TRANSDUCER CONNECTIONS 7.4. ALARMS 7.5. ANALOG SIGNAL FOLLOWERS 8.1. POWER ON/OFF 8.2. CHANGING THE COMMAND SET POINT 8.3. OVERRIDE OPEN 8.4. OVERRIDE CLOSED 8.0 Manual Operation 8.5. SETTING A CHANNEL TO AUTO CONTROL 8.6. SETTING A CHANNEL TO DIRECTLY METER INCOMING SIGNALS 8.7. SETTING A CHANNEL TO DISPLAY THE TOTALIZER FUNCTION Page 9.0 External/Remote Operation 9.1. SELECTING EXTERNAL/REMOTE OPERATION (Front Panel Only) 9.2. CHOOSING RS-232 COMMUNICATION 9.3. CHOOSING RS-485 COMMUNICATION 10.1. ENTERING THE SETUP/CAL MODE 10.0 Setup/Cal Mode 10.2.3. Selecting Unit-of-Measure 10.2.4. Selecting Gas ID 10.2.5. Setting A/D Conversion Rate (Filter) 10.2.6. Front Panel Lock Out 10.3. TOTALIZER SETUP 10.3.1. Count Up to a Set Point 10.3.2. Count Down from a Set Point 10.3.3. Count Continuously 10.4. EXTERNAL COMMUNICATION SETUP 10.4.1. RS-232 Settings 10.4.2. RS-485 Settings 10.5. SELECTING THE ANALOG SIGNAL LEVEL 10.5.1. Zero to Five Volt Operation 10.5.2. Zero to Ten Volt Operation 10.5.3. Four to Twenty Milliamp Operation 10.6. SETTING LIMIT ALARMS 10.6.1. Setting a Single Channels High Limit 10.6.2. Setting a Single Channels Low Limit 10.6.3. Setting a Single Channels Hysteresis 10.7. SETTING RATIO CONTROL PARAMETERS Enabling Ratio Control 10.8. CALIBRATING A CHANNEL TO ITS INCOMING SIGNALS 10.8.1. Resetting the Zero Only 10.8.2. Resetting the Span Only 10.8.3. Resetting Zero and Span 10.8.4. Setting a Multiplication Factor 10.9. SERIAL COMMUNICATION 10.9.1. Commands 10.9.2. Set Point Queries 10.9.3. Alarm/Flag Queries Page 11.0 Appendix A 164-122012 PowerPOD 400 Page 30 of 42 Power -400 Serial Commands APPENDIX A (Cont.) Power -400 Serial Commands (Cont'd) Page 12.0 Appendix B 13.0 Appendix C Units-of-Measure for Meter Reading & Corresponding Totalizer Units Gas ID Table (Page 1 of 2) Gas ID Table (Page 2 of 2) 14.0 Appendix D Setting the Zero & Span on the PowerPod-400 Power Supply/Totalizer Page Page Page Page 15.0 Drawings P ower 400 16.0 Warranty 16.1. Warranty Repair Policy 16.2. Non-Warranty Repair Policy