Teledyne powerpod 400 Gas ID Table (Page 2 of 2)

164-122012 PowerPOD 400 Page 35 of 42

Gas ID Table (Page 2 of 2)

GAS NAME Symbol GAS NAME Symbol GAS NAME Symbol

136 Pentane C5H12 156 R143 R143 175 Toluene C7H8

137 Perchloryl Fluoride ClFO3 157 R143A R143A

176 Transbutene C4H8

138 Perfluorocyclobutane C4F8 158 R152A R152A 177 Trichloroethane 177

139 R116 C2F6 159 R218 C3F8 178 Trichloroethylene 178

140 Perfluoropropane C3F8 160 R1416 R1416 179 R113 R113

141 Phenol C6H6O 161 Radon Rn

180 Triethylamine 180

142 Phosgene COCl2 162 Sec-butanol 162 181 Trimethyl Amine C3H9N

143 Phosphine PH3 163 Silane SiH4 182 Tungsten Hexafluoride WF6

144 Phosphorus Trifluoride PF3 164 Silicone Tetrafluoride SiF4 183 Uranium Hexafluoride UF6

145 Propane C3H8 165 Sulfur Dioxide SO2 184 Vinyl Bromide 184

146 Propyl Alcohol C3H8O 166 Sulfur Hexafluoride SF6 185 Vinyl Chloride 185

147 Propyl Amine C3H9N 167 Sulfur Tetrafluoride SF4 186 Vinyl Flouride C2H3F

148 Propylene C3H6 168 Sulfur Trifluoride SF3 187 Water Vapor H2O

149 Pyradine C5H5N 169 Sulfur Trioxide SO3 188 Xenon Xe

150 R32 CH2F2 170 Tetrachloroethylene 170 189 Xylene, m- C8H10

151 R123 R123

171 Tetrafluoroethylene C2F4 190 Xylene, o- C8H10

152 R123A R123A 172 Tetrahydrofuran C4H8O 191 Xylene, p- C8H10

153 R125 C2HF5 173 Tert-butanol 173

191 Mixtures MIXT

154 R134 R134 174 Thiophene C4H4S 193 Other ????

155 R134A R134A

194

Contents

Main Manual Print History Visit www.teledyne-hi.com for WEEE disposal guidance. Table of Contents Page 1.0 Quick Start Instructions P 2.0 Safety 3.0 Features Page 4.0 Specifications PowerPod-400 Specifications Table 5.0 Front Panel 7 P ower 1 4 0 9 3 6 8 6.0 Rear Panel 7.1. POWER 7.2. COMMUNICATIONS 7.0 Wiring 7.3. TRANSDUCER CONNECTIONS 7.4. ALARMS 7.5. ANALOG SIGNAL FOLLOWERS 8.1. POWER ON/OFF 8.2. CHANGING THE COMMAND SET POINT 8.3. OVERRIDE OPEN 8.4. OVERRIDE CLOSED 8.0 Manual Operation 8.5. SETTING A CHANNEL TO AUTO CONTROL 8.6. SETTING A CHANNEL TO DIRECTLY METER INCOMING SIGNALS 8.7. SETTING A CHANNEL TO DISPLAY THE TOTALIZER FUNCTION Page 9.0 External/Remote Operation 9.1. SELECTING EXTERNAL/REMOTE OPERATION (Front Panel Only) 9.2. CHOOSING RS-232 COMMUNICATION 9.3. CHOOSING RS-485 COMMUNICATION 10.1. ENTERING THE SETUP/CAL MODE 10.0 Setup/Cal Mode 10.2.3. Selecting Unit-of-Measure 10.2.4. Selecting Gas ID 10.2.5. Setting A/D Conversion Rate (Filter) 10.2.6. Front Panel Lock Out 10.3. TOTALIZER SETUP 10.3.1. Count Up to a Set Point 10.3.2. Count Down from a Set Point 10.3.3. Count Continuously 10.4. EXTERNAL COMMUNICATION SETUP 10.4.1. RS-232 Settings 10.4.2. RS-485 Settings 10.5. SELECTING THE ANALOG SIGNAL LEVEL 10.5.1. Zero to Five Volt Operation 10.5.2. Zero to Ten Volt Operation 10.5.3. Four to Twenty Milliamp Operation 10.6. SETTING LIMIT ALARMS 10.6.1. Setting a Single Channels High Limit 10.6.2. Setting a Single Channels Low Limit 10.6.3. Setting a Single Channels Hysteresis 10.7. SETTING RATIO CONTROL PARAMETERS Enabling Ratio Control 10.8. CALIBRATING A CHANNEL TO ITS INCOMING SIGNALS 10.8.1. Resetting the Zero Only 10.8.2. Resetting the Span Only 10.8.3. Resetting Zero and Span 10.8.4. Setting a Multiplication Factor 10.9. SERIAL COMMUNICATION 10.9.1. Commands 10.9.2. Set Point Queries 10.9.3. Alarm/Flag Queries Page 11.0 Appendix A 164-122012 PowerPOD 400 Page 30 of 42 Power -400 Serial Commands APPENDIX A (Cont.) Power -400 Serial Commands (Cont'd) Page 12.0 Appendix B 13.0 Appendix C Units-of-Measure for Meter Reading & Corresponding Totalizer Units Gas ID Table (Page 1 of 2) Gas ID Table (Page 2 of 2) 14.0 Appendix D Setting the Zero & Span on the PowerPod-400 Power Supply/Totalizer Page Page Page Page 15.0 Drawings P ower 400 16.0 Warranty 16.1. Warranty Repair Policy 16.2. Non-Warranty Repair Policy