PowerPod-400 Serial Commands Contd | Teledyne powerpod 400 instruction

APPENDIX A (Cont.)

PowerPod-400 Serial Commands (Cont'd)

Command	Name	Query	Response
D1<d >	Ch1 Disp Mode		D1 d	note 5
D2<d>	Ch2 Disp Mode		D2 d
D3<d >	Ch3 Disp Mode		D3 d
D4<d >	Ch4 Disp Mode		D4 d
T1S<dddddd>	Totalizer Set Point, Ch1	T1S	T1S dddddd
T2S<dddddd>	Totalizer Set Point, Ch2	T2S	T2S dddddd
T3S<dddddd>	Totalizer Set Point, Ch3	T3S	T3S dddddd
T4S<dddddd>	Totalizer Set Point, Ch4	T4S	T4S dddddd
T1M<d>	Totalizer Mode, Ch1	T1M	T1M d	note 8
T2M<d>	Totalizer Mode, Ch2	T2M	T2M d
T3M<d>	Totalizer Mode, Ch3	T3M	T3M d
T4M<d>	Totalizer Mode, Ch4	T4M	T4M d
T1R	Totalizer Reset, Ch1			note 8
T2R	Totalizer Reset, Ch2
T3R	Totalizer Reset, Ch3
T4R	Totalizer Reset, Ch4
	Totalizer Flag, Ch1	TF1	TF1 d	note 9
	Totalizer Flag, Ch2	TF2	TF2 d
	Totalizer Flag, Ch3	TF3	TF3 d
	Totalizer Flag, Ch4	TF4	TF4 d
SN1<d.dddd>	Cal Value, CH1	SN1	SN1 d.dddd	notes 1, 2
SN2<dd.ddd>	Cal Value, CH2	SN2	SN2 d.dddd
SN3<ddd.dd>	Cal Value, CH3	SN3	SN3 d.dddd
SN4<dddd.d>	Cal Value, CH4	SN4	SN4 d.dddd
Z1	Zero Ch1
Z2	Zero Ch2
Z3	Zero Ch3
Z4	Zero Ch4
F1	Set Full Scale Value, Ch1
F2	Set Full Scale Value, Ch2
F3	Set Full Scale Value, Ch3
F4	Set Full Scale Value, Ch4
			OCA: CH1 text CH2 text	Note 10
	Status, All Channels	ST	CH3 text CH4 text
	Status, All Channels	ST	HI/LO: CH1 d/d CH2 d/d
			HI/LO: CH1 d/d CH2 d/d
			CH3 d/d CH4 d/d
R1<d>	Ratio Mode, Ch1	R1	R1 d	note 11
R2<d>	Ratio Mode, Ch2	R2	R2 d
R3<d>	Ratio Mode, Ch3	R3	R3 d
R4<d>	Ratio Mode, Ch4	R4	R4 d
BR<d>	Baud Rate	BR	BR d	note 12
RE<d>	Front Panel Lock Out	RE	REn: REMOTE/LOCAL	note 13
*00X<dd>	Multi-drop Address	*00X	MULTIDROP ADDRESS: dd

164-122012 PowerPOD 400

Page 31 of 42

Image 31

Teledyne powerpod 400 instruction manual PowerPod-400 Serial Commands Contd

Contents

Teledyne Hastings Manual Print History Table of Contents Four to Twenty Milliamp Operation Quick Start Instructions Power Safety Front Panel Lockout Features Power Selection PowerPod-400 Specifications Table Specifications Channel Number Select Keys Front Panel Rear Panel Power WiringCommunications Transducer Connections Alarms Analog Signal Followers Override Open Power ON/OFFChanging the Command SET Point Manual Operation Setting a Channel to Directly Meter Incoming Signals Setting a Channel to Auto ControlSetting a Channel to Display the Totalizer Function Mode Reset Value Choosing RS-232 Communication External/Remote OperationChoosing RS-485 Communication Blanking a Display Line/Channel Setup/Cal ModeEntering the SETUP/CAL Mode Display Setup Selecting Unit-of-Measure Setting A/D Conversion Rate FilterSelecting Gas ID Front Panel Lock Out Totalizer SetupCount Up to a Set Point Count Down from a Set Point External Communication SetupRS-232 Settings RS-485 Settings Four to Twenty Milliamp Operation Selecting the Analog Signal LevelZero to Five Volt Operation Zero to Ten Volt Operation Setting a Single Channel’s Hysteresis Setting Limit AlarmsSetting a Single Channel’s High Limit Setting a Single Channel’s Low Limit Enabling Ratio Control Setting Ratio Control Parameters Resetting the Zero Only Calibrating a Channel to ITS Incoming SignalsResetting the Span Only Setting a Multiplication Factor Resetting Zero and Span Set Point Queries CommandsAlarm/Flag Queries Serial Communication PowerPOD Appendix a PowerPod-400 Serial Commands PowerPod-400 Serial Commands Contd Appendix a Notes Name Rate Total ApppendixCB Gas ID Table Page 1 Gas ID Table Page 2 Appendix D Setting the Zero & Span PowerPod-400 Power Supply/Totalizer Zeroing Unit 4 to 20 mA Range Spanning Unit Transducer POWERPOD-400 PowerPOD Drawings Warranty Repair Policy Warranty