Selecting Holdqueue, 10Press the Holdqueue key | Toshiba 210C

1. SCANNING THE IMAGE DATA (Cont.)

Scan Setting on the Touch Panel (Cont.)

16Press the Scan! key (or the START key on the control panel).

-Scanning starts and the image data are transmitted to the entered mail address after the scanning operation has been completed.

-When the originals are set on the original glass , perform the operation on page 8-9 continually.

-The volume of the high-resolution image data may be very large. When selecting ATTACHMENT , be careful not to ex- ceed the mail server capacity of both the transmitter and the receiver.

-When changing the sender’s address or the mail server ca- pacity, etc., refer to the Operator’s Manual for the Printer Con- troller (User Document CD-ROM).

Selecting HOLDQUEUE

If you want to use the scanned data at the ‘Command WorkstationTM’ or ‘WebSpoolerTM’, select the HOLDQUEUE key.

10Press the HOLDQUEUE key.

-If you want to store in the ‘Mailbox’ or ‘E-mail’ as well, make the settings for each destination before pressing the Scan! key.

8

11Press the Scan! key (or the START key on the control panel).

-Scanning starts.

-When the originals are set on the original glass continually, perform the operation on page 8-9.

8-8NETWORK SCANNING FUNCTION (USING THE OPTIONAL PRINTER CONTROLLER)

Image 140

Toshiba 210C 16Press the Scan! key or the Start key on the control panel, Selecting Holdqueue, 10Press the Holdqueue key

Contents

Operators Manual for Copying Functions Trademarks Toshiba Quality is Second to None Supplies / Parts General Toshiba Quality is Second to NoneToners Preface Features of the e-STUDIO210c/310c Preface Table of Contents Table of Contents Maintenance Selecting finishing modes Using the optional finishersWhen the graphic symbols flash on the touch panel Precautions Installation General Precautions Be sure to disconnect the power-cord plugHandle and use the copier gently and carefully Machine Noise Information Precautions Copying Prohibition Label Explanatory Label Fixing the adjusters stoppers FORGERYPREVENTIONFUNCTION/STORAGEOFCOLOURCOPIES Before Making Copies Main Components Optional Equipment Configuration Optional Equipment Control Panel Access Code key Colour Mode Selection keyFunction Clear key Stop key Touch-keys Touch PanelMessage Display Clearing the Functions Selected Set functions confirmation key Turning on the Power Switch Turn on the power switch Controlling the Use of the Copier with Access Codes After Copying is Finished Turning on the Power Switch Sleep mode When the copier is used also as a printer Power consumption and warm-up time at energy saving modeENERGY-SAVING Functions Off-mode Base model 12BEFORE Making Copies HOW to Make Copies Place the originals General Copying ProceduresPlace paper in the cassettes To make multiple sets of copies When Coming Across the Situations belowPlace the next original 2nd side and press the Start key Setting Copy Paper Acceptable Copy Paper Types and Sizes Recommended Paper/Handling and Storing Paper Recommended PaperHandling and Storing Paper Pay attention to the following points Setting Copy Paper Setting the Cassette for THIN/THICK1/OHP Film Setting is completed THICK1 or Thin or OHP key Setting Originals Acceptable Original Types and Sizes Setting Originals When Placing an Original on the Glass When Using the Reversing Automatic Document Feeder optional Continuous Feed Mode Nals When the original starts being pulled in, let go of it Slide Auto JOB Start JOB Preset Cancelling the auto job start during warming upDuring Warming up Place paper in the cassettes. Place the originals. Cancelling Preset Job during Copying During Copying Select copy modes as required and press the Start key Auto JOB Start JOB PresetDuring Printing optional Interrupt Copying Replace the original with a new one To resume copying CANCELLING/RESUMING a Copy OperationTo cancel the copy job Setting of Basic Copy Modes Paper Selection Automatic Paper Selection APS Manual Paper Selection Reduction and Enlargement Copying Press the AMS key Press the Original Size key of the same size as the original Press the cassette icon representing the desired copy Reduction and Enlargement CopyingPaper size, then press the ZOOM···· key Duplex Copying 1-SIDED, 2-SIDED, BOOK-TYPE Duplex Copying 1-SIDED, 2-SIDED, BOOK-TYPE Sided Originals 2-Sided Copies When using this mode in bypass copying Press the Start key Book-Type Originals 2-Sided Copies Press the Book 2 key Select the book copying type Copy Density Adjustment Colour Mode Original Mode Advanced Image 16SETTING of Basic Copy Modes Colour Editing Adjustment Monocolour Copying Press the SET key HUE AdjustmentPress the Start key Cancelling the Hue Adjustment Press the Start key Cancelling the Saturation Adjustment Saturation Colour Balance Ymck Adjustment Press the Start key Cancelling the Colour Balance Adjustment RGB Adjustment Press the Start key Cancelling the RGB Adjustment ONE-TOUCH Adjustment Background Adjustment Press the Start key Cancelling the Background Adjustment Sharpness Adjustment Press the Start key Cancelling the Sharpness Adjustment 10COLOUR Editing and Adjustment Using the Editing Functions Image Shift Providing Right or Left Margin Adjust the binding margin, then press the SET key Press the Start key Providing a Bookbinding Margin Edge Erase Book Centre Erase DUAL-PAGE Page Full Image 1 / 4 1 / 4 in 1 Select the type of the original Magazine Sort from the Editing Menu Magazine Sort from the Editing Menu Press Start key Y Zoom Press the lower SET key Press the Trim or Mask key Image EditingTrimming/Masking Place an original on the glass to specify the area Enter the distance values read in for Specified area Press the Mirror key Image EditingMirror Image Negative/Positive Reversal Press the NEG/POS key Centring Press the ALL or Part key to select the area for centring Enter the distance values read in for the specified area Image Repeat Enter the distance values read for the area to be re- peated Press the lower SET key Select the repeat number 22USING the Editing Functions Using the Special Functions Continuous Original Feeding / Single Original Feeding Place an original Select either the Automatic Paper Selection 2or Automatic Magnification Selection modeMIXED-SIZED Originals Bypass Copy Mode Bypass Copying Bypass Copying Bypass Copying Bypass Copying on Standard Size or A3-wide Paper Perform steps 1 to 2 on Then press the lower SET key Bypass Copying on Non-standard Size PaperPerform steps 1 to 3 on Press the NON-STANDARD key Storing a Non-Standard Size in the Memory Press the desired Memory Number key Thin Paper/Thick Paper/Sticker Labels Specify the paper size as required OHP Films Mode Memory Copies will be made in the recalled copy modes Mode Memory Confirming Stored Copy Modes Setting the Other Size KEY Setting has been completed User Selection Initial Settings Press the icons of the settings you desire selectedSettings will be shaded, then press the SET key Right are initial settings default settingsPage Weekly Timer Check the settings on the display, and if correctionsAre necessary, press the Change key Set the ON/OFF times for each day of the week Cancelling the Use of the Weekly Timer Setting the Clock to the Daylight Saving Time System Setting the Date and TimeCheck that the settings are all correct Total Counter Department Management Department management menu appears Printing an Access Code List An output example of the access code list Setting Access Codes Registration/Change/Deletion Press the Enable key, then the SET keyDepartment Management Press the key of the desired function Registering a New Access Code When the ID Change key is selected in step When the Limitation key is selected in step Resetting Counters Automatic Calibration Press the Calibration key Switching Between Languages Press the key of the desired language Setting the Energy Saving Mode Clearing the Automatic Energy Saving Mode Setting the OFF-MODE Auto Shutoff Clearing the Off-Mode/Sleep ModeSelect the period of time in minutes on the dis Controller is activated Using the Optional Finishers Selecting Finishing Modes Finishing Modes and Finishers Optional Names of the Main Components SORT/GROUP Copying Staple Sorting 90 g/m² 105 g/m² A4, B5, LT MAGAZINESORT&SADDLESTITCHINGMODEBOOKLETMODE Place paper in the cassettes. Set the paper size Conditions Making Saddle Stitching Possible LT-R Hole Punching Mode Number of punch holes and available paper sizes Using the Optional Printer Controller Network Scanning Function Scanning the Image Data Scan Setting on the Touch PanelScan setting Select the Scan key Press the Setting key Set the scanning conditionsPress the PRINTER/NETWORK key Scanning the Image Data Selecting Mailbox Confirm the entered file nameSelect the method for storing the image data desti- nation 13Press the Scan! keyor the Start key on the control panel Selecting E-MAIL 13Confirm the entered e-mail address 16Press the Scan! key or the Start key on the control panel Selecting Holdqueue10Press the Holdqueue key 11Press the Scan! key or the Start key on the control panel Touch Panel during Scanning Shutting Downthe Power Supplytothe Printer Controller Press the Shutdown key Press the YES key When the Graphic Symbols Flash on the Touch Panel Description Ofthe Flashing Graphic Symbols ADD Paper Symbol Adding Paper to the Cassettes ADD Paper Symbol Adding Paper to the Large-Capacity Feeder optionalOpen the cover of the large-capacity feeder optional Place paper in the large-capacity feeder Replace Toner Cartridge Symbol Open the front covers in the order of to Replace Toner Cartridge Symbol Close the covers in the order of to Replace Toner BAG Symbol Replace Toner BAG Symbol Clear Paper Symbol Clear Paper Symbol Remove any misfed paperPage Paper Misfeed on the Bypass Guide Page Exit guide Lower guide Push the lever to lift the lower guide plate Be careful not to have the guide plate drop GuidePage Remove any misfed paper in the paper exit area Page 20WHEN the Graphic Symbols Flash on the Touch Panel Adding Staples Optional Adding Staples Optional Page Return the saddle stitch holder and the saddle Stitching unit to their respective original positionsMake sure that the finisher is attached to the copier Firmly and that A3, B4 or A4-R size paper is set Removing Jammed Staples Optional Removing Jammed Staples OPTIONALCont Clearingaccumulated Punched Paper Bits Optional Call Service Symbol Periodic Maintenance Message 30WHEN the Graphic Symbols Flash on the Touch Panel Maintenance Daily Inspection Cleaning the Original GlassPower switch ON/OFF status Cleaning the Reversing Automatic Document Feeder optional Copier does not start Simple TroubleshootingDisplay does not change when keys or icons are pressed Copies are stained Copy density is too lowCopy density is too high Simple Troubleshooting Copy images are blurredImages are partially missing Functions cannot be set Specifications & Options STUDIO210c/310c Specifications 11-3 STUDIO210c/310c Specifications Continuous Copying Speed Specifications of Options 11-5 Specifications of Options Additional Cassette Module Finishers LD,LG,LT-R,COMP Specification of Options Hole Punch Unit Options for MJ-1019/MJ-1020 11-9 11-10SPECIFICATIONS & Options Packing List Copying Function Combination APS Image Quality Adjustment Combination Matrix Index Numbers Index 11-8 11-15 10-4 Periodic Maintenance To Service Technicians For Copying Functions