During Copying, Cancelling Preset Job during Copying | Toshiba 210C

During Copying

You can preset the next copy modes during a copy run.

You cannot preset the next copy modes during the scanning of the originals.

1 Place the original(s).	Page 2-9	2

2 Press the JOB PRESET key during a copy run.

-The following message appears:

JOB PRESETTING

Select other copy modes as required.

3

4

Press the START key.

The preset job will start when the current copying is finished.

If the copy run is interrupted due to running out of paper, etc.during job presetting, press the JOB PRESET key to set the desired copy modes again after the copy operation restarts.

Cancelling Preset Job during Copying

To cancel the preset copy job, press the JOB CANCEL key.

2-15

Image 41

Toshiba 210C manual During Copying, Cancelling Preset Job during Copying

Contents

Operators Manual for Copying Functions Trademarks Supplies / Parts Toshiba Quality is Second to None General Toshiba Quality is Second to NoneToners Preface Preface Features of the e-STUDIO210c/310c Table of Contents Table of Contents Maintenance Selecting finishing modes Using the optional finishersWhen the graphic symbols flash on the touch panel Installation Precautions Be sure to disconnect the power-cord plug General PrecautionsHandle and use the copier gently and carefully Machine Noise Information Copying Prohibition Label Explanatory Label Precautions Fixing the adjusters stoppers FORGERYPREVENTIONFUNCTION/STORAGEOFCOLOURCOPIES Before Making Copies Main Components Optional Equipment Optional Equipment Configuration Control Panel Colour Mode Selection key Access Code keyFunction Clear key Stop key Touch-keys Touch PanelMessage Display Set functions confirmation key Clearing the Functions Selected Turn on the power switch Turning on the Power Switch After Copying is Finished Controlling the Use of the Copier with Access Codes Turning on the Power Switch Power consumption and warm-up time at energy saving mode Sleep mode When the copier is used also as a printerENERGY-SAVING Functions Off-mode Base model 12BEFORE Making Copies HOW to Make Copies Place the originals General Copying ProceduresPlace paper in the cassettes To make multiple sets of copies When Coming Across the Situations belowPlace the next original 2nd side and press the Start key Acceptable Copy Paper Types and Sizes Setting Copy Paper Recommended Paper Recommended Paper/Handling and Storing PaperHandling and Storing Paper Pay attention to the following points Setting Copy Paper Setting the Cassette for THIN/THICK1/OHP Film THICK1 or Thin or OHP key Setting is completed Acceptable Original Types and Sizes Setting Originals When Placing an Original on the Glass Setting Originals When Using the Reversing Automatic Document Feeder optional Nals Continuous Feed Mode When the original starts being pulled in, let go of it Slide Cancelling the auto job start during warming up Auto JOB Start JOB PresetDuring Warming up Place paper in the cassettes. Place the originals. During Copying Cancelling Preset Job during Copying Select copy modes as required and press the Start key Auto JOB Start JOB PresetDuring Printing optional Replace the original with a new one Interrupt Copying To resume copying CANCELLING/RESUMING a Copy OperationTo cancel the copy job Setting of Basic Copy Modes Automatic Paper Selection APS Paper Selection Manual Paper Selection Press the AMS key Reduction and Enlargement Copying Press the Original Size key of the same size as the original Press the cassette icon representing the desired copy Reduction and Enlargement CopyingPaper size, then press the ZOOM···· key Duplex Copying 1-SIDED, 2-SIDED, BOOK-TYPE Duplex Copying 1-SIDED, 2-SIDED, BOOK-TYPE Sided Originals 2-Sided Copies When using this mode in bypass copying Press the Start key Book-Type Originals 2-Sided Copies Press the Book 2 key Select the book copying type Copy Density Adjustment Colour Mode Advanced Image Original Mode 16SETTING of Basic Copy Modes Colour Editing Adjustment Monocolour Copying Press the SET key HUE AdjustmentPress the Start key Cancelling the Hue Adjustment Saturation Press the Start key Cancelling the Saturation Adjustment Press the Start key Cancelling the Colour Balance Adjustment Colour Balance Ymck Adjustment Press the Start key Cancelling the RGB Adjustment RGB Adjustment ONE-TOUCH Adjustment Press the Start key Cancelling the Background Adjustment Background Adjustment Press the Start key Cancelling the Sharpness Adjustment Sharpness Adjustment 10COLOUR Editing and Adjustment Using the Editing Functions Providing Right or Left Margin Image Shift Press the Start key Providing a Bookbinding Margin Adjust the binding margin, then press the SET key Edge Erase Book Centre Erase DUAL-PAGE Page Full Image 1 / 4 Select the type of the original 1 / 4 in 1 Magazine Sort from the Editing Menu Press Start key Magazine Sort from the Editing Menu Press the lower SET key Y Zoom Press the Trim or Mask key Image EditingTrimming/Masking Enter the distance values read in for Specified area Place an original on the glass to specify the area Press the Mirror key Image EditingMirror Image Press the NEG/POS key Negative/Positive Reversal Press the ALL or Part key to select the area for centring Centring Enter the distance values read in for the specified area Image Repeat Press the lower SET key Select the repeat number Enter the distance values read for the area to be re- peated 22USING the Editing Functions Using the Special Functions Continuous Original Feeding / Single Original Feeding Place an original Select either the Automatic Paper Selection 2or Automatic Magnification Selection modeMIXED-SIZED Originals Bypass Copying Bypass Copy Mode Bypass Copying Bypass Copying Perform steps 1 to 2 on Bypass Copying on Standard Size or A3-wide Paper Then press the lower SET key Bypass Copying on Non-standard Size PaperPerform steps 1 to 3 on Press the NON-STANDARD key Press the desired Memory Number key Storing a Non-Standard Size in the Memory Specify the paper size as required Thin Paper/Thick Paper/Sticker Labels OHP Films Mode Memory Copies will be made in the recalled copy modes Confirming Stored Copy Modes Mode Memory Setting has been completed Setting the Other Size KEY Press the icons of the settings you desire selected User Selection Initial SettingsSettings will be shaded, then press the SET key Right are initial settings default settingsPage Check the settings on the display, and if corrections Weekly TimerAre necessary, press the Change key Set the ON/OFF times for each day of the week Cancelling the Use of the Weekly Timer Setting the Clock to the Daylight Saving Time System Setting the Date and TimeCheck that the settings are all correct Total Counter Department management menu appears Department Management An output example of the access code list Printing an Access Code List Press the Enable key, then the SET key Setting Access Codes Registration/Change/DeletionDepartment Management Press the key of the desired function Registering a New Access Code When the Limitation key is selected in step When the ID Change key is selected in step Resetting Counters Automatic Calibration Press the Calibration key Press the key of the desired language Switching Between Languages Clearing the Automatic Energy Saving Mode Setting the Energy Saving Mode Clearing the Off-Mode/Sleep Mode Setting the OFF-MODE Auto ShutoffSelect the period of time in minutes on the dis Controller is activated Selecting Finishing Modes Using the Optional Finishers Names of the Main Components Finishing Modes and Finishers Optional SORT/GROUP Copying Staple Sorting 90 g/m² 105 g/m² A4, B5, LT Place paper in the cassettes. Set the paper size MAGAZINESORT&SADDLESTITCHINGMODEBOOKLETMODE LT-R Conditions Making Saddle Stitching Possible Number of punch holes and available paper sizes Hole Punching Mode Network Scanning Function Using the Optional Printer Controller Scanning the Image Data Scan Setting on the Touch PanelScan setting Select the Scan key Press the Setting key Set the scanning conditionsPress the PRINTER/NETWORK key Scanning the Image Data Selecting Mailbox Confirm the entered file nameSelect the method for storing the image data desti- nation Selecting E-MAIL 13Press the Scan! keyor the Start key on the control panel 13Confirm the entered e-mail address Selecting Holdqueue 16Press the Scan! key or the Start key on the control panel10Press the Holdqueue key 11Press the Scan! key or the Start key on the control panel Touch Panel during Scanning Press the Shutdown key Press the YES key Shutting Downthe Power Supplytothe Printer Controller When the Graphic Symbols Flash on the Touch Panel Description Ofthe Flashing Graphic Symbols Adding Paper to the Cassettes ADD Paper Symbol Adding Paper to the Large-Capacity Feeder optional ADD Paper SymbolOpen the cover of the large-capacity feeder optional Place paper in the large-capacity feeder Open the front covers in the order of to Replace Toner Cartridge Symbol Close the covers in the order of to Replace Toner Cartridge Symbol Replace Toner BAG Symbol Replace Toner BAG Symbol Clear Paper Symbol Remove any misfed paper Clear Paper SymbolPage Paper Misfeed on the Bypass Guide Page Exit guide Lower guide Be careful not to have the guide plate drop Guide Push the lever to lift the lower guide platePage Remove any misfed paper in the paper exit area Page 20WHEN the Graphic Symbols Flash on the Touch Panel Adding Staples Optional Adding Staples Optional Page Stitching unit to their respective original positions Return the saddle stitch holder and the saddleMake sure that the finisher is attached to the copier Firmly and that A3, B4 or A4-R size paper is set Removing Jammed Staples Optional Removing Jammed Staples OPTIONALCont Clearingaccumulated Punched Paper Bits Optional Call Service Symbol Periodic Maintenance Message 30WHEN the Graphic Symbols Flash on the Touch Panel Maintenance Daily Inspection Cleaning the Original GlassPower switch ON/OFF status Cleaning the Reversing Automatic Document Feeder optional Copier does not start Simple TroubleshootingDisplay does not change when keys or icons are pressed Copies are stained Copy density is too lowCopy density is too high Copy images are blurred Simple TroubleshootingImages are partially missing Functions cannot be set Specifications & Options STUDIO210c/310c Specifications 11-3 Continuous Copying Speed STUDIO210c/310c Specifications 11-5 Specifications of Options Additional Cassette Module Specifications of Options LD,LG,LT-R,COMP Finishers Hole Punch Unit Options for MJ-1019/MJ-1020 Specification of Options 11-9 Packing List 11-10SPECIFICATIONS & Options APS Copying Function Combination Image Quality Adjustment Combination Matrix Numbers Index 11-8 Index 11-15 10-4 To Service Technicians Periodic Maintenance For Copying Functions