STUDIO210c/310c Specifications | Toshiba 210C specification

1. e-STUDIO210c/310c SPECIFICATIONS (Cont.)

Continuous Copying Speed

Mode	Paper Size	Feeder	e-STUDIO210c		e-STUDIO310c

			Full colour	Black	Full colour	Black

	A4, B5, A5-R,	Cassette	21 sheets/min.	31 sheets/min.	31 sheets/min.
	LT, ST-R, 8.5”SQ	Large-capacityfeeder(A4)

		Bypass	21 sheets/min.	24 sheets/min.	24 sheets/min.

	A4-R, B5-R,	Cassette	17 sheets/min.	23 sheets/min.	23 sheets/min.

	LT-R	Bypass	17 sheets/min.	19 sheets/min.	19 sheets/min.

Plain Paper,	B4, FOLIO, LG,	Cassette	14 sheets/min.	19 sheets/min.	19 sheets/min.

THIN	COMP, 13”LG	Bypass	14 sheets/min.	16 sheets/min.	16 sheets/min.

	A3,	Cassette	12 sheets/min.	16 sheets/min.	16 sheets/min.

	LD	Bypass	12 sheets/min.	14 sheets/min.	14 sheets/min.

	A6-R	Bypass	21 sheets/min.	24 sheets/min.	24 sheets/min.

	A3-wide (305x457mm)	Bypass	12 sheets/min.	12 sheets/min.	12 sheets/min.

	A4, B5, A5-R,	Cassette/Bypass		10.3 sheets/min.
	LT, ST-R	Large-capacityfeeder(A4)		10.3 sheets/min.
	LT, ST-R	Large-capacityfeeder(A4)

	A4-R, B5-R,	Cassette		9.3 sheets/min.
	LT-R	Bypass		9.3 sheets/min.
	LT-R	Bypass

THICK1	B4, FOLIO	Cassette		8.5 sheets/min.
	LG, COMP	Bypass		8.5 sheets/min.
	LG, COMP	Bypass

	A3,	Cassette		7.9 sheets/min.
	LD	Bypass		7.9 sheets/min.
	LD	Bypass

	A6-R	Bypass		10.3 sheets/min.

	A3-wide (305x457mm)	Bypass		7.7 sheets/min.

THICK2	All sizes	Bypass		2~6 sheets/min.

THICK3	All sizes	Bypass		2~6 sheets/min.

OHP FILM	A4	Cassette/Bypass		3.3 sheets/min.

Note 1: The values above are measured when originals are set on the original glass, and single-sided, 100% copies are made.

11 Note 2: The bypass copying speed is measured with the paper size specified.

Note 3: Copying speeds of THICK2 and THICK3 vary depending on the user’s environment (environmental temperature) and the paper type.

*The paper mentioned above is Toshiba-recommended paper. Specifications and appearance are subject to change without notice in the interest of product improvement.

11-4SPECIFICATIONS & OPTIONS

Image 182

Toshiba 210C manual STUDIO210c/310c Specifications, Continuous Copying Speed

Contents

Operators Manual for Copying Functions Trademarks Toshiba Quality is Second to None Supplies / Parts General Toshiba Quality is Second to NoneToners Preface Features of the e-STUDIO210c/310c Preface Table of Contents Table of Contents Maintenance Selecting finishing modes Using the optional finishersWhen the graphic symbols flash on the touch panel Precautions Installation Handle and use the copier gently and carefully General PrecautionsBe sure to disconnect the power-cord plug Machine Noise Information Precautions Copying Prohibition Label Explanatory Label Fixing the adjusters stoppers FORGERYPREVENTIONFUNCTION/STORAGEOFCOLOURCOPIES Before Making Copies Main Components Optional Equipment Configuration Optional Equipment Control Panel Function Clear key Access Code keyColour Mode Selection key Stop key Touch-keys Touch PanelMessage Display Clearing the Functions Selected Set functions confirmation key Turning on the Power Switch Turn on the power switch Controlling the Use of the Copier with Access Codes After Copying is Finished Turning on the Power Switch ENERGY-SAVING Functions Sleep mode When the copier is used also as a printerPower consumption and warm-up time at energy saving mode Off-mode Base model 12BEFORE Making Copies HOW to Make Copies Place the originals General Copying ProceduresPlace paper in the cassettes To make multiple sets of copies When Coming Across the Situations belowPlace the next original 2nd side and press the Start key Setting Copy Paper Acceptable Copy Paper Types and Sizes Handling and Storing Paper Recommended Paper/Handling and Storing PaperRecommended Paper Pay attention to the following points Setting Copy Paper Setting the Cassette for THIN/THICK1/OHP Film Setting is completed THICK1 or Thin or OHP key Setting Originals Acceptable Original Types and Sizes Setting Originals When Placing an Original on the Glass When Using the Reversing Automatic Document Feeder optional Continuous Feed Mode Nals When the original starts being pulled in, let go of it Slide During Warming up Auto JOB Start JOB PresetCancelling the auto job start during warming up Place paper in the cassettes. Place the originals. Cancelling Preset Job during Copying During Copying Select copy modes as required and press the Start key Auto JOB Start JOB PresetDuring Printing optional Interrupt Copying Replace the original with a new one To resume copying CANCELLING/RESUMING a Copy OperationTo cancel the copy job Setting of Basic Copy Modes Paper Selection Automatic Paper Selection APS Manual Paper Selection Reduction and Enlargement Copying Press the AMS key Press the Original Size key of the same size as the original Press the cassette icon representing the desired copy Reduction and Enlargement CopyingPaper size, then press the ZOOM···· key Duplex Copying 1-SIDED, 2-SIDED, BOOK-TYPE Duplex Copying 1-SIDED, 2-SIDED, BOOK-TYPE Sided Originals 2-Sided Copies When using this mode in bypass copying Press the Start key Book-Type Originals 2-Sided Copies Press the Book 2 key Select the book copying type Copy Density Adjustment Colour Mode Original Mode Advanced Image 16SETTING of Basic Copy Modes Colour Editing Adjustment Monocolour Copying Press the SET key HUE AdjustmentPress the Start key Cancelling the Hue Adjustment Press the Start key Cancelling the Saturation Adjustment Saturation Colour Balance Ymck Adjustment Press the Start key Cancelling the Colour Balance Adjustment RGB Adjustment Press the Start key Cancelling the RGB Adjustment ONE-TOUCH Adjustment Background Adjustment Press the Start key Cancelling the Background Adjustment Sharpness Adjustment Press the Start key Cancelling the Sharpness Adjustment 10COLOUR Editing and Adjustment Using the Editing Functions Image Shift Providing Right or Left Margin Adjust the binding margin, then press the SET key Press the Start key Providing a Bookbinding Margin Edge Erase Book Centre Erase DUAL-PAGE Page Full Image 1 / 4 1 / 4 in 1 Select the type of the original Magazine Sort from the Editing Menu Magazine Sort from the Editing Menu Press Start key Y Zoom Press the lower SET key Press the Trim or Mask key Image EditingTrimming/Masking Place an original on the glass to specify the area Enter the distance values read in for Specified area Press the Mirror key Image EditingMirror Image Negative/Positive Reversal Press the NEG/POS key Centring Press the ALL or Part key to select the area for centring Enter the distance values read in for the specified area Image Repeat Enter the distance values read for the area to be re- peated Press the lower SET key Select the repeat number 22USING the Editing Functions Using the Special Functions Continuous Original Feeding / Single Original Feeding Place an original Select either the Automatic Paper Selection 2or Automatic Magnification Selection modeMIXED-SIZED Originals Bypass Copy Mode Bypass Copying Bypass Copying Bypass Copying Bypass Copying on Standard Size or A3-wide Paper Perform steps 1 to 2 on Then press the lower SET key Bypass Copying on Non-standard Size PaperPerform steps 1 to 3 on Press the NON-STANDARD key Storing a Non-Standard Size in the Memory Press the desired Memory Number key Thin Paper/Thick Paper/Sticker Labels Specify the paper size as required OHP Films Mode Memory Copies will be made in the recalled copy modes Mode Memory Confirming Stored Copy Modes Setting the Other Size KEY Setting has been completed Settings will be shaded, then press the SET key User Selection Initial SettingsPress the icons of the settings you desire selected Right are initial settings default settingsPage Are necessary, press the Change key Weekly TimerCheck the settings on the display, and if corrections Set the ON/OFF times for each day of the week Cancelling the Use of the Weekly Timer Setting the Clock to the Daylight Saving Time System Setting the Date and TimeCheck that the settings are all correct Total Counter Department Management Department management menu appears Printing an Access Code List An output example of the access code list Department Management Setting Access Codes Registration/Change/DeletionPress the Enable key, then the SET key Press the key of the desired function Registering a New Access Code When the ID Change key is selected in step When the Limitation key is selected in step Resetting Counters Automatic Calibration Press the Calibration key Switching Between Languages Press the key of the desired language Setting the Energy Saving Mode Clearing the Automatic Energy Saving Mode Select the period of time in minutes on the dis Setting the OFF-MODE Auto ShutoffClearing the Off-Mode/Sleep Mode Controller is activated Using the Optional Finishers Selecting Finishing Modes Finishing Modes and Finishers Optional Names of the Main Components SORT/GROUP Copying Staple Sorting 90 g/m² 105 g/m² A4, B5, LT MAGAZINESORT&SADDLESTITCHINGMODEBOOKLETMODE Place paper in the cassettes. Set the paper size Conditions Making Saddle Stitching Possible LT-R Hole Punching Mode Number of punch holes and available paper sizes Using the Optional Printer Controller Network Scanning Function Scanning the Image Data Scan Setting on the Touch PanelScan setting Select the Scan key Press the Setting key Set the scanning conditionsPress the PRINTER/NETWORK key Scanning the Image Data Selecting Mailbox Confirm the entered file nameSelect the method for storing the image data desti- nation 13Press the Scan! keyor the Start key on the control panel Selecting E-MAIL 13Confirm the entered e-mail address 10Press the Holdqueue key 16Press the Scan! key or the Start key on the control panelSelecting Holdqueue 11Press the Scan! key or the Start key on the control panel Touch Panel during Scanning Shutting Downthe Power Supplytothe Printer Controller Press the Shutdown key Press the YES key When the Graphic Symbols Flash on the Touch Panel Description Ofthe Flashing Graphic Symbols ADD Paper Symbol Adding Paper to the Cassettes Open the cover of the large-capacity feeder optional ADD Paper SymbolAdding Paper to the Large-Capacity Feeder optional Place paper in the large-capacity feeder Replace Toner Cartridge Symbol Open the front covers in the order of to Replace Toner Cartridge Symbol Close the covers in the order of to Replace Toner BAG Symbol Replace Toner BAG Symbol Clear Paper Symbol Clear Paper Symbol Remove any misfed paperPage Paper Misfeed on the Bypass Guide Page Exit guide Lower guide Push the lever to lift the lower guide plate Be careful not to have the guide plate drop GuidePage Remove any misfed paper in the paper exit area Page 20WHEN the Graphic Symbols Flash on the Touch Panel Adding Staples Optional Adding Staples Optional Page Make sure that the finisher is attached to the copier Return the saddle stitch holder and the saddleStitching unit to their respective original positions Firmly and that A3, B4 or A4-R size paper is set Removing Jammed Staples Optional Removing Jammed Staples OPTIONALCont Clearingaccumulated Punched Paper Bits Optional Call Service Symbol Periodic Maintenance Message 30WHEN the Graphic Symbols Flash on the Touch Panel Maintenance Daily Inspection Cleaning the Original GlassPower switch ON/OFF status Cleaning the Reversing Automatic Document Feeder optional Copier does not start Simple TroubleshootingDisplay does not change when keys or icons are pressed Copies are stained Copy density is too lowCopy density is too high Images are partially missing Simple TroubleshootingCopy images are blurred Functions cannot be set Specifications & Options STUDIO210c/310c Specifications 11-3 STUDIO210c/310c Specifications Continuous Copying Speed Specifications of Options 11-5 Specifications of Options Additional Cassette Module Finishers LD,LG,LT-R,COMP Specification of Options Hole Punch Unit Options for MJ-1019/MJ-1020 11-9 11-10SPECIFICATIONS & Options Packing List Copying Function Combination APS Image Quality Adjustment Combination Matrix Index Numbers Index 11-8 11-15 10-4 Periodic Maintenance To Service Technicians For Copying Functions