Anchor Bolts, Anchor Bolt Installation Detail | Toshiba 300 KW

10.3Anchor Bolts

Install the anchor bolts to secure the UPS on the floor. See Figure 10.2 for anchor bolt installation detail. Use 12mm (1/2”) diameter anchor bolts. There are 16mm (5/8”) diameter holes provided in the UPS base. See Figure 10.3 for the hole locations and dimensions for the specified UPS models.

					4 of 16mm-diameter				4 screw holes
					(5/8”) screw holes				(Side View)

Anchor Bolt

FIGURE 10.2

FIGURE 10.2

ANCHOR BOLT INSTALLATION DETAIL

ANCHOR BOLT INSTALLATION DETAIL

< 100kVA (T80S3K10KK6XS2H) >

Back

551mm

4 x 12mm-Dia. (1/2”) (21” 11/16) Front

754mm (29” 11/16)

<100kVA (T80S3K10KK6XSNH) >

<150/225kVA >

Back

551mm

4 x 12mm-Dia. (1/2”) (21” 11/16) Front

1,170mm (46” 1/16)

< 250/300kVA >

		Back
	8 x 12mm-Dia. (1/2”)			650mm
	8 x 12mm-Dia. (1/2”)			(25” 19/32)
				(25” 19/32)
		Front
	572mm	572mm	572mm
	(22” 1/2)	(22” 1/2)	(22” 1/2)

FIGURE 10.3

HOLE LOCATIONS/DIMENSIONS

ON BOTTOM OF UPS

28	G8000 Series Installation and Operation Manual

Image 36

Toshiba 300 KW operation manual Anchor Bolts, Anchor Bolt Installation Detail

Contents

G8000 Series Page Document July Qualified Personnel only Uninterruptible Power System UPS Purpose Toshiba’s Customer Support CenterToshiba Customer Support Center Toshiba International Corporation Table of Contents 11.4 Introduction General Safety Instructions SymbolsProhibited Symbol indicates do not take action Signal Words Qualified Personnel Important Safety Instructions Factory Authorized Personnel Safety Precautions Disclaimer General Maintenance Keep the area arround the UPS cleanTransporting/Unpacking Do not tilt the UPS more than 10 from upright position Do not transport, move, store, or place the UPS on its side Avoid vibration or shock exceeding 0.5G Inspection/Storage Installation Precautions Install the UPS in a controlled environmentKeep the Specified Clearance around the UPS Do not install the UPS where water may fall on it Do not block air vents Installation Precautions Environment standard Metal Conduit is not AN Acceptable Ground Conductor Routing and Grounding Wiring/Connection Perform wiring and connections with correct polarityConnect only one 1 ground wire to the earth ground terminal Follow the torque criteria for tightening screws For 100, 150, 225KVA GND 150/225 KVA UPS Warning Labels Weight and Dimensions Model Unit Shipping 300 KVA UPS Exterior Dimensions Inches Transporting Transporting By Crane 8.5 show examples of acceptable and unacceptable operations Transporting By Forklift Transporting UPS by Forklift Operating Precautions Storage/Operating EnvironmentPage Maintenance Precautions Qualified Personnel onlyQualified Personnel shall Disposal Do not dispose of the batteries in a fireDo not open or mutilate the batteries Installation Unpacking UPS Clearance Anchor Bolt Installation Detail Anchor Bolts UPS Wiring External Wiring Diagram 11.1 100 kVA Terminal Blocks and Power Cables Block Number Cable Size Tightening Torque AC Input Bypass Input AC Output Battery YA36L Block Number Cable Size Recommended Fastener Torque Bus Number Cable Size Recommended Fastener Torque UPS Power Cable Knockout Plates Bottom Cable Knockout Plates for 100 KVA T80S3K10KK6XS2H Plate #2 Plate #3 Terminal Knockout Plates for the 300 KVA UPS Grounding Wire External BreakersBe sure to ground the UPS as specified G8000 100 kVA G8000 150/225 kVA Control Wires Signal Name Operation 11 Connection Between UPS, Battery Cabinet & Bypass Breaker Grounding Configuration 12 Grounding Configuration with Input Neutral Grounded Grounding Configuration without input neutral Recommended Configuration for delta-input Grounding Configuration with corner-grounded delta-input 16 Grounding Configuration with CORNER-GROUNDED DELTA-INPUT UPS Specifications General SpecificationMechanical Specification Terms Specification Remarks Nominal Capacity 150 kW 225 kW 300 kW Electrical Specification Do not open the front cover Operator Interface UPS may not respond if the button press is too short Key-Switch and Buttons Graphic Display Panel KEY-SWITCH/OPERATING Buttons 13.2 LCD/LED Indicators Graphic Display Panel LCD/LED Indicators LCD Indicators Name Description Normal Display AC-VO AC- I O 50%Volt Freq .0Hz 50% AC I/P-V Freq .0Hz BYP I/P-V Freq .0HzDC-V BATT-V BATT- I 0A 32TIM Fault Display 09-09-06 LCD Scroll Abbreveations EPO and Control Power Supply Operating Switches Operating the UPS Operation Types Pre-operational CheckPerform the pre-operational check before operating the UPS Startup Procedures Procedure to start the UPS is shown in Steps AC Vo 480 AC Io 50% Switch Power Supply UPS→Bypass Bypass LED is on Stop Complete Shutdown DC-V 0 BATT-V 0 BATT-I 0 a Changing Between Float Charge and Equalize Charge Make sure that the Float Charge LED is on Make sure that the Equal Charge LED is on Troubleshooting Emergency Power Off EPOTypes of Errors Faults and Warnings Data Screen 09-09-06 LCD Fault & Warning Displays Fault Display Fault Messages LCD Message Indication Description LCD Message Indication Description LCD Scroll w/ faults or warnings Reset Contact Toshiba in the event of malfunction or fault Restoring UPS OperationDo not attempt to modify or relocate the UPS Do not open the front and/or rear panelsPage Page Industrial Division