UPS Specifications, General Specification | Toshiba 300 KW instruction

12 UPS Specifications

12.1General Specification

Terms	Specification	Remarks
Conforming Standard	UL1778-2001	UL, cUL
Ambient Temperature	PF = 1.0: 32 – 86 °F (0 – 30 °C)
Ambient Temperature	PF = 0.8: 86 – 104 °F (30 – 40 °C)
	PF = 0.8: 86 – 104 °F (30 – 40 °C)
Relative Humidity	30% – 90%	Non-condensing
	< 3280 ft. (< 1000 m)	Contact Toshiba Technical
Altitude		Support for installation above
		3280 ft. (1000 m)
Audible Noise	68 dB (100/150/225 kVA), 72 dB (300 kVA)	39 in. (1m) away from front
Insulation Resistance	3 MΩ	With 500V-Megger
	AC 2 kV – 1 min.	Main Circuit
Insulation Breakdown	AC 1.5 kV – 1 min.	External Interface
	AC 500 V – 1 min.	Control Circuit

12.2Mechanical Specification

	Nominal Capacity	100 kW:
	Nominal Capacity	T80S3K10KK6XS2H
		T80S3K10KK6XS2H
	Cabinet Protection	IEC298 IP20*
	Conformity	IEC298 IP20*
	Conformity
	Exterior Paint	Sherwin Williams, HHT2-7055, 079 Beige Texture
		FRONT: 1.6 mm (1/16 in.)
	Panel Thickness	BACK/SIDE/TOP: 1.2 mm (3/64 in.)
		BOTTOM: 3.2 mm (1/8 in.)
	Input/Output	BOTTOM
	Cabling Entrance	BOTTOM
	Cabling Entrance
	Ground/Control	BOTTOM
	Wiring Entrance	BOTTOM
	Wiring Entrance
		W: 36.8 in. (935 mm)
	Outline Dimension	D: 31.8 in. (808 mm)
		H: 79.2 in. (2012 mm)
	Unit Weight	1740 lb. (789 kg)
	Shipping Weight	1790 lb. (812 kg)
	Floor Loading Per	2180 lb./ft.2
	Footprint	(10,644 kg/m2)
		FRONT: 43 7/16 in. (1100 mm)
	Clearance	BACK/SIDE: 0 in. (0 mm)
		TOP: 15 3/4 in. (400 mm)
	Heat Rejection	34,121 BTU/h
	Heat Rejection	(8598 kcal/h)
		(8598 kcal/h)
*IP20: Foreign objects that are 12 mm (15/32”) or larger are prevented from entering the enclosure of the UPS.
G8000 Series Installation and Operation Manual				43

Image 51

Toshiba 300 KW UPS Specifications, General Specification, Mechanical Specification, Terms Specification Remarks

Contents

G8000 Series Page Document July Qualified Personnel only Uninterruptible Power System UPS Toshiba International Corporation PurposeToshiba’s Customer Support Center Toshiba Customer Support Center Table of Contents 11.4 Introduction General Safety Instructions SymbolsProhibited Symbol indicates do not take action Qualified Personnel Signal Words Factory Authorized Personnel Important Safety Instructions Disclaimer Safety Precautions Do not tilt the UPS more than 10 from upright position General MaintenanceKeep the area arround the UPS clean Transporting/Unpacking Avoid vibration or shock exceeding 0.5G Do not transport, move, store, or place the UPS on its side Inspection/Storage Installation Precautions Install the UPS in a controlled environmentKeep the Specified Clearance around the UPS Do not block air vents Do not install the UPS where water may fall on it Environment standard Installation Precautions Conductor Routing and Grounding Metal Conduit is not AN Acceptable Ground Follow the torque criteria for tightening screws Wiring/ConnectionPerform wiring and connections with correct polarity Connect only one 1 ground wire to the earth ground terminal For 100, 150, 225KVA GND 150/225 KVA UPS Warning Labels Model Unit Shipping Weight and Dimensions 300 KVA UPS Exterior Dimensions Inches Transporting 8.5 show examples of acceptable and unacceptable operations Transporting By Crane Transporting UPS by Forklift Transporting By Forklift Storage/Operating Environment Operating PrecautionsPage Maintenance Precautions Qualified Personnel onlyQualified Personnel shall Disposal Do not dispose of the batteries in a fireDo not open or mutilate the batteries Installation UPS Clearance Unpacking Anchor Bolts Anchor Bolt Installation Detail External Wiring Diagram UPS Wiring Block Number Cable Size Tightening Torque 11.1 100 kVA Terminal Blocks and Power Cables AC Input Bypass Input AC Output Battery Block Number Cable Size Recommended Fastener Torque YA36L Bus Number Cable Size Recommended Fastener Torque Bottom Cable Knockout Plates for 100 KVA T80S3K10KK6XS2H UPS Power Cable Knockout Plates Terminal Knockout Plates for the 300 KVA UPS Plate #2 Plate #3 Grounding Wire External BreakersBe sure to ground the UPS as specified G8000 100 kVA G8000 150/225 kVA Signal Name Operation Control Wires 11 Connection Between UPS, Battery Cabinet & Bypass Breaker 12 Grounding Configuration with Input Neutral Grounded Grounding Configuration Recommended Configuration for delta-input Grounding Configuration without input neutral 16 Grounding Configuration with CORNER-GROUNDED DELTA-INPUT Grounding Configuration with corner-grounded delta-input Terms Specification Remarks UPS SpecificationsGeneral Specification Mechanical Specification Nominal Capacity 150 kW 225 kW 300 kW Do not open the front cover Electrical Specification UPS may not respond if the button press is too short Operator Interface Graphic Display Panel KEY-SWITCH/OPERATING Buttons Key-Switch and Buttons Graphic Display Panel LCD/LED Indicators 13.2 LCD/LED Indicators Name Description LCD Indicators 50% Normal DisplayAC-VO AC- I O 50% Volt Freq .0Hz 32TIM AC I/P-V Freq .0HzBYP I/P-V Freq .0Hz DC-V BATT-V BATT- I 0A 09-09-06 Fault Display Abbreveations LCD Scroll Operating the UPS EPO and Control Power Supply Operating Switches Operation Types Pre-operational CheckPerform the pre-operational check before operating the UPS Procedure to start the UPS is shown in Steps Startup Procedures AC Vo 480 AC Io 50% Bypass LED is on Switch Power Supply UPS→Bypass Stop DC-V 0 BATT-V 0 BATT-I 0 a Complete Shutdown Make sure that the Float Charge LED is on Changing Between Float Charge and Equalize Charge Make sure that the Equal Charge LED is on Troubleshooting Emergency Power Off EPOTypes of Errors 09-09-06 Faults and Warnings Data Screen Fault Display LCD Fault & Warning Displays LCD Message Indication Description Fault Messages LCD Message Indication Description Reset LCD Scroll w/ faults or warnings Do not open the front and/or rear panels Contact Toshiba in the event of malfunction or faultRestoring UPS Operation Do not attempt to modify or relocate the UPSPage Page Industrial Division