LCD Fault & Warning Displays, Fault Display | Toshiba 300 KW

15.3LCD Fault & Warning Displays

When a fault occurs, a screen is shown as in Figure 15.2. When a warning occurs, a screen is shown as in Figure 15.3. Select the desired fault or warning data to be displayed using the scroll buttons.

BYPASS

FAULT STOP

FAULTS & WARNINGS

1 FUSE BLOWN

09-09-06 08:05:30

FIGURE 15.2 - FAULT DISPLAY

UPS SUPPLY

AC-VO 480[V]

AC- I O 50[%]

FAULTS & WARNINGS

1 UPS OVERLOAD

09-09-06 08:05:30

FIGURE 15.3 - WARNING DISPLAY

G8000 Series Installation and Operation Manual

65

Image 73

Toshiba 300 KW operation manual LCD Fault & Warning Displays, Fault Display

Contents

G8000 Series Page Document July Qualified Personnel only Uninterruptible Power System UPS Toshiba’s Customer Support Center PurposeToshiba Customer Support Center Toshiba International Corporation Table of Contents 11.4 Introduction Symbols General Safety InstructionsProhibited Symbol indicates do not take action Qualified Personnel Signal Words Factory Authorized Personnel Important Safety Instructions Disclaimer Safety Precautions Keep the area arround the UPS clean General MaintenanceTransporting/Unpacking Do not tilt the UPS more than 10 from upright position Avoid vibration or shock exceeding 0.5G Do not transport, move, store, or place the UPS on its side Inspection/Storage Install the UPS in a controlled environment Installation PrecautionsKeep the Specified Clearance around the UPS Do not block air vents Do not install the UPS where water may fall on it Environment standard Installation Precautions Conductor Routing and Grounding Metal Conduit is not AN Acceptable Ground Perform wiring and connections with correct polarity Wiring/ConnectionConnect only one 1 ground wire to the earth ground terminal Follow the torque criteria for tightening screws For 100, 150, 225KVA GND 150/225 KVA UPS Warning Labels Model Unit Shipping Weight and Dimensions 300 KVA UPS Exterior Dimensions Inches Transporting 8.5 show examples of acceptable and unacceptable operations Transporting By Crane Transporting UPS by Forklift Transporting By Forklift Storage/Operating Environment Operating PrecautionsPage Qualified Personnel only Maintenance PrecautionsQualified Personnel shall Do not dispose of the batteries in a fire DisposalDo not open or mutilate the batteries Installation UPS Clearance Unpacking Anchor Bolts Anchor Bolt Installation Detail External Wiring Diagram UPS Wiring Block Number Cable Size Tightening Torque 11.1 100 kVA Terminal Blocks and Power Cables AC Input Bypass Input AC Output Battery Block Number Cable Size Recommended Fastener Torque YA36L Bus Number Cable Size Recommended Fastener Torque Bottom Cable Knockout Plates for 100 KVA T80S3K10KK6XS2H UPS Power Cable Knockout Plates Terminal Knockout Plates for the 300 KVA UPS Plate #2 Plate #3 External Breakers Grounding WireBe sure to ground the UPS as specified G8000 100 kVA G8000 150/225 kVA Signal Name Operation Control Wires 11 Connection Between UPS, Battery Cabinet & Bypass Breaker 12 Grounding Configuration with Input Neutral Grounded Grounding Configuration Recommended Configuration for delta-input Grounding Configuration without input neutral 16 Grounding Configuration with CORNER-GROUNDED DELTA-INPUT Grounding Configuration with corner-grounded delta-input General Specification UPS SpecificationsMechanical Specification Terms Specification Remarks Nominal Capacity 150 kW 225 kW 300 kW Do not open the front cover Electrical Specification UPS may not respond if the button press is too short Operator Interface Graphic Display Panel KEY-SWITCH/OPERATING Buttons Key-Switch and Buttons Graphic Display Panel LCD/LED Indicators 13.2 LCD/LED Indicators Name Description LCD Indicators AC-VO AC- I O 50% Normal DisplayVolt Freq .0Hz 50% BYP I/P-V Freq .0Hz AC I/P-V Freq .0HzDC-V BATT-V BATT- I 0A 32TIM 09-09-06 Fault Display Abbreveations LCD Scroll Operating the UPS EPO and Control Power Supply Operating Switches Pre-operational Check Operation TypesPerform the pre-operational check before operating the UPS Procedure to start the UPS is shown in Steps Startup Procedures AC Vo 480 AC Io 50% Bypass LED is on Switch Power Supply UPS→Bypass Stop DC-V 0 BATT-V 0 BATT-I 0 a Complete Shutdown Make sure that the Float Charge LED is on Changing Between Float Charge and Equalize Charge Make sure that the Equal Charge LED is on Emergency Power Off EPO TroubleshootingTypes of Errors 09-09-06 Faults and Warnings Data Screen Fault Display LCD Fault & Warning Displays LCD Message Indication Description Fault Messages LCD Message Indication Description Reset LCD Scroll w/ faults or warnings Restoring UPS Operation Contact Toshiba in the event of malfunction or faultDo not attempt to modify or relocate the UPS Do not open the front and/or rear panelsPage Page Industrial Division