Electrical Specification | Toshiba 300 KW specs

12.3Electrical Specification

WARNING

DO NOT open the front cover.

Electric shock, burns or other personal injuries may occur if untrained personnel open the front cover.

Nominal Capacity	100 kW	150 kW	225 kW	300 kW
AC Input Rated Capacity*	110 kW (120 kW)	165 kW (180 kW)	245 kW (270 kW)	320 kW (320 kW)
Input Voltage		480 V ( +10% to -15% ), 3-Phase 3-Wire
Input Frequency		60 Hz ±5%
Input Power Factor		0.95 – 1.00 Lagging ( at 100% Load )
Current Harmonic Distortion		4% Maximum ( at 100% Load )
Input Capacity Required*	111 kVA (124 kVA)	166 kVA (184 kVA)	250 kVA (274 kVA)	327 kVA (332 kVA)
Circuit Breaker Rating At 480 V	200 A Trip	300 A Trip	450 A Trip	500 A Trip
Input
	* Capacity: Normal Mode (Recharge Mode)

Nominal Capacity	100 kW	150 kW	225 kW	300 kW
DC Input Voltage Window		288 – 414 VDC
Recharge Voltage Regulation		± 1.5%

Nominal Capacity	100 kW	150 kW	225 kW	300 kW
AC Output Rated Capacity*	100 kVA (100 kW)	150 kVA (150 kW)	225 kVA (225 kW)	300 kVA (300 kW)
Output Voltage		480/277 V ± 1%, 3-Phase 4-Wire
Output Power Factor		1.0 PF: 32 – 86 °F (0 – 30 °C)
		0.8 PF: 86 – 104 °F (30 – 40 °C)
Voltage Distortion	3% with 100% Linear Load / 5% with Non-Linear Load
Transient Voltage Regulation		< ± 2%
Transient Settling Time		< 50 ms
Crest Factor		2.0
Output Frequency		60 Hz ± 0.01% ( at Free-running Mode)
Synchronous Window To Utility Line		59 Hz – 61 Hz
Frequency Slew Rate		1 Hz/Sec
Over Load Rating	100% – Continuous / 125% – 10 min. / 150% – 1 min.

* Capacity: Normal Mode (Recharge Mode)

G8000 Series Installation and Operation Manual

45

Image 53

Toshiba 300 KW operation manual Electrical Specification, Do not open the front cover

Contents

G8000 Series Page Document July Qualified Personnel only Uninterruptible Power System UPS Toshiba’s Customer Support Center PurposeToshiba Customer Support Center Toshiba International Corporation Table of Contents 11.4 Introduction Prohibited Symbol indicates do not take action General Safety InstructionsSymbols Qualified Personnel Signal Words Factory Authorized Personnel Important Safety Instructions Disclaimer Safety Precautions Keep the area arround the UPS clean General MaintenanceTransporting/Unpacking Do not tilt the UPS more than 10 from upright position Avoid vibration or shock exceeding 0.5G Do not transport, move, store, or place the UPS on its side Inspection/Storage Keep the Specified Clearance around the UPS Installation PrecautionsInstall the UPS in a controlled environment Do not block air vents Do not install the UPS where water may fall on it Environment standard Installation Precautions Conductor Routing and Grounding Metal Conduit is not AN Acceptable Ground Perform wiring and connections with correct polarity Wiring/ConnectionConnect only one 1 ground wire to the earth ground terminal Follow the torque criteria for tightening screws For 100, 150, 225KVA GND 150/225 KVA UPS Warning Labels Model Unit Shipping Weight and Dimensions 300 KVA UPS Exterior Dimensions Inches Transporting 8.5 show examples of acceptable and unacceptable operations Transporting By Crane Transporting UPS by Forklift Transporting By Forklift Storage/Operating Environment Operating PrecautionsPage Qualified Personnel shall Maintenance PrecautionsQualified Personnel only Do not open or mutilate the batteries DisposalDo not dispose of the batteries in a fire Installation UPS Clearance Unpacking Anchor Bolts Anchor Bolt Installation Detail External Wiring Diagram UPS Wiring Block Number Cable Size Tightening Torque 11.1 100 kVA Terminal Blocks and Power Cables AC Input Bypass Input AC Output Battery Block Number Cable Size Recommended Fastener Torque YA36L Bus Number Cable Size Recommended Fastener Torque Bottom Cable Knockout Plates for 100 KVA T80S3K10KK6XS2H UPS Power Cable Knockout Plates Terminal Knockout Plates for the 300 KVA UPS Plate #2 Plate #3 Be sure to ground the UPS as specified Grounding WireExternal Breakers G8000 100 kVA G8000 150/225 kVA Signal Name Operation Control Wires 11 Connection Between UPS, Battery Cabinet & Bypass Breaker 12 Grounding Configuration with Input Neutral Grounded Grounding Configuration Recommended Configuration for delta-input Grounding Configuration without input neutral 16 Grounding Configuration with CORNER-GROUNDED DELTA-INPUT Grounding Configuration with corner-grounded delta-input General Specification UPS SpecificationsMechanical Specification Terms Specification Remarks Nominal Capacity 150 kW 225 kW 300 kW Do not open the front cover Electrical Specification UPS may not respond if the button press is too short Operator Interface Graphic Display Panel KEY-SWITCH/OPERATING Buttons Key-Switch and Buttons Graphic Display Panel LCD/LED Indicators 13.2 LCD/LED Indicators Name Description LCD Indicators AC-VO AC- I O 50% Normal DisplayVolt Freq .0Hz 50% BYP I/P-V Freq .0Hz AC I/P-V Freq .0HzDC-V BATT-V BATT- I 0A 32TIM 09-09-06 Fault Display Abbreveations LCD Scroll Operating the UPS EPO and Control Power Supply Operating Switches Perform the pre-operational check before operating the UPS Operation TypesPre-operational Check Procedure to start the UPS is shown in Steps Startup Procedures AC Vo 480 AC Io 50% Bypass LED is on Switch Power Supply UPS→Bypass Stop DC-V 0 BATT-V 0 BATT-I 0 a Complete Shutdown Make sure that the Float Charge LED is on Changing Between Float Charge and Equalize Charge Make sure that the Equal Charge LED is on Types of Errors TroubleshootingEmergency Power Off EPO 09-09-06 Faults and Warnings Data Screen Fault Display LCD Fault & Warning Displays LCD Message Indication Description Fault Messages LCD Message Indication Description Reset LCD Scroll w/ faults or warnings Restoring UPS Operation Contact Toshiba in the event of malfunction or faultDo not attempt to modify or relocate the UPS Do not open the front and/or rear panelsPage Page Industrial Division