Toshiba 300 KW specification

The UPS battery cabinet and bypass breaker should be wired as shown below in Figure 11.11.

Power Source Jumper wire if battery

OH is not applied

TC

		To Bypass
		Input
	10
	11
	12
	13	Power Source
	14	Power Source
	14	for trip coil
	15
	16
	17
	18
	19	To DC
	20	To DC
	20	Input
	21
	22
	TB1
	UPS Cabinet	Ext. EPO (Customer) N.O. Contacts
		Ext. EPO (Customer) N.O. Contacts

Bypass Breaker

Overheat

B-Contact

Auxillary A- contact

Battery Cabinet

FIGURE 11.11 - CONNECTION BETWEEN UPS, BATTERY CABINET & BYPASS BREAKER

G8000 Series Installation and Operation Manual

39

Image 47

Toshiba 300 KW operation manual Connection Between UPS, Battery Cabinet & Bypass Breaker

Contents

G8000 Series Page Document July Qualified Personnel only Uninterruptible Power System UPS Toshiba International Corporation PurposeToshiba’s Customer Support Center Toshiba Customer Support Center Table of Contents 11.4 Introduction Prohibited Symbol indicates do not take action General Safety InstructionsSymbols Qualified Personnel Signal Words Factory Authorized Personnel Important Safety Instructions Disclaimer Safety Precautions Do not tilt the UPS more than 10 from upright position General MaintenanceKeep the area arround the UPS clean Transporting/Unpacking Avoid vibration or shock exceeding 0.5G Do not transport, move, store, or place the UPS on its side Inspection/Storage Keep the Specified Clearance around the UPS Installation PrecautionsInstall the UPS in a controlled environment Do not block air vents Do not install the UPS where water may fall on it Environment standard Installation Precautions Conductor Routing and Grounding Metal Conduit is not AN Acceptable Ground Follow the torque criteria for tightening screws Wiring/ConnectionPerform wiring and connections with correct polarity Connect only one 1 ground wire to the earth ground terminal For 100, 150, 225KVA GND 150/225 KVA UPS Warning Labels Model Unit Shipping Weight and Dimensions 300 KVA UPS Exterior Dimensions Inches Transporting 8.5 show examples of acceptable and unacceptable operations Transporting By Crane Transporting UPS by Forklift Transporting By Forklift Storage/Operating Environment Operating PrecautionsPage Qualified Personnel shall Maintenance PrecautionsQualified Personnel only Do not open or mutilate the batteries DisposalDo not dispose of the batteries in a fire Installation UPS Clearance Unpacking Anchor Bolts Anchor Bolt Installation Detail External Wiring Diagram UPS Wiring Block Number Cable Size Tightening Torque 11.1 100 kVA Terminal Blocks and Power Cables AC Input Bypass Input AC Output Battery Block Number Cable Size Recommended Fastener Torque YA36L Bus Number Cable Size Recommended Fastener Torque Bottom Cable Knockout Plates for 100 KVA T80S3K10KK6XS2H UPS Power Cable Knockout Plates Terminal Knockout Plates for the 300 KVA UPS Plate #2 Plate #3 Be sure to ground the UPS as specified Grounding WireExternal Breakers G8000 100 kVA G8000 150/225 kVA Signal Name Operation Control Wires 11 Connection Between UPS, Battery Cabinet & Bypass Breaker 12 Grounding Configuration with Input Neutral Grounded Grounding Configuration Recommended Configuration for delta-input Grounding Configuration without input neutral 16 Grounding Configuration with CORNER-GROUNDED DELTA-INPUT Grounding Configuration with corner-grounded delta-input Terms Specification Remarks UPS SpecificationsGeneral Specification Mechanical Specification Nominal Capacity 150 kW 225 kW 300 kW Do not open the front cover Electrical Specification UPS may not respond if the button press is too short Operator Interface Graphic Display Panel KEY-SWITCH/OPERATING Buttons Key-Switch and Buttons Graphic Display Panel LCD/LED Indicators 13.2 LCD/LED Indicators Name Description LCD Indicators 50% Normal DisplayAC-VO AC- I O 50% Volt Freq .0Hz 32TIM AC I/P-V Freq .0HzBYP I/P-V Freq .0Hz DC-V BATT-V BATT- I 0A 09-09-06 Fault Display Abbreveations LCD Scroll Operating the UPS EPO and Control Power Supply Operating Switches Perform the pre-operational check before operating the UPS Operation TypesPre-operational Check Procedure to start the UPS is shown in Steps Startup Procedures AC Vo 480 AC Io 50% Bypass LED is on Switch Power Supply UPS→Bypass Stop DC-V 0 BATT-V 0 BATT-I 0 a Complete Shutdown Make sure that the Float Charge LED is on Changing Between Float Charge and Equalize Charge Make sure that the Equal Charge LED is on Types of Errors TroubleshootingEmergency Power Off EPO 09-09-06 Faults and Warnings Data Screen Fault Display LCD Fault & Warning Displays LCD Message Indication Description Fault Messages LCD Message Indication Description Reset LCD Scroll w/ faults or warnings Do not open the front and/or rear panels Contact Toshiba in the event of malfunction or faultRestoring UPS Operation Do not attempt to modify or relocate the UPSPage Page Industrial Division