Toshiba 300 KW 49, 13.3 LCD Indicators

G8000 Series Installation and Operation Manual

13.3 LCD Indicators

The operator can scroll through the following LCD display screens using the scroll buttons.

TABLE 13.1 - LCD DISPLAY SCREENS

Name Description

Normal Display Displays operational status, operational guidance, and measured

data.

Fault Display Displays detailed data when a fault occurs.

Warning Display Displays detailed data when a warning occurs.

FIGURE 13.3 - CHANGING SCREENS WITH SCROLL BUTTONS

SCROLL UP

SCROLL DOWN

NORMAL DISPLAY

WARNIG DISPLAY

FAULT DISPLAY

Contents

Main Page Page NOTICE QUALIFIED PERSONNEL ONLY UNINTERRUPTIBLE POWER SYSTEM (UPS) Purpose Toshibas Customer Support Center i Table of Contents ii 1 Introduction SAVE THESE INSTRUCTIONS 2 2 General Safety Instructions 2.1 Symbols 3 2.2 Signal Words 2.3 Qualied Personnel DANGER WARNING CAUTION ATTENTION 4 3 Important Safety Instructions 5 4 Safety Precautions 4.1 Disclaimer 6 4.3 Transporting/Unpacking 4.2 General Maintenance BACKSIDE 8 4.4 Inspection/Storage 5 Installation Precautions 10 Page 12 13 5.1 Wiring/Connection 14 6 Warning Labels (control power source switch) DANGER AC VOLTA GE REFER TO INSTRUCTION MANUAL FOR WIRE SIZE AND TIGHTENING TORQUE USE COPPER CONDUCTORS ONLY! 12 13 (B) DANGER AC VOLTA GE (D) REFER TO INSTRUCTION MANUAL FOR WIRE SIZE AND TIGHTENING TORQUE USE COPPER CONDUCTORS ONLY! 12 13 Page 7 Weight and Dimensions 18 8 Transporting 20 8.1 Transporting By Crane 8.1 Transporting By Crane 21 8.2 Transporting By Forklift 22 9 Storage/Operating Environment 9.1 Operating Precautions Page 24 9.2 Maintenance Precautions 25 DANGER 9.3 Disposal 26 10 Installation Page 28 A 26 10.3 Anchor Bolts FIGURE 10.2 ANCHOR BOLT INSTALLATION DETAIL FIGURE 10.3 HOLE LOCATIONS/DIMENSIONS ON BOTTOM OF UPS < 100kVA (T80S3K10KK6XSNH) > < 150/225kV > 11 UPS Wiring 11 UPS Wiring 11.1 Terminal Blocks and Power Cables 1 2 3 4 5 6 7 8 9 10 11 12 13 - 31 11.2 150, 225, and 300 kVA Buss Strip Terminals and Power Cables 32 Page 34 11.3 UPS Power Cable Knockout Plates 30 30 - 35 - + 36 11.4 External Breakers 11.5 Grounding Wire G8000 - 100 kVA G8000 - 300 kVA G8000 - 150/225 kVA Page The UPS battery cabinet and bypass breaker should be wired as shown below in Figure 11.11. 40 11.7 Grounding Conguration 300 kVA B 11.7.1 Recommended conguration (for 4 wire input with Input Neutral grounded) 41 11.7.2 Grounding Conguration (without input neutral) 11.7.3 Recommended Conguration (for delta-input) 42 11.7.4 Grounding Conguration (with corner-grounded delta-input) 43 12 UPS Specications 12.1 General Specication 12.2 Mechanical Specication 44 12.2 Mechanical Specication (cont.) 45 12.3 Electrical Specication 46 13 Operator Interface Table 13.1 shows the functions of the operating buttons on the graphic display panel. Page 48 13.2 LCD/LED Indicators 49 13.3 LCD Indicators Page Page Page 53 13.6 LCD Scroll 54 14 Operating the UPS 55 14.1 Operation Types 14.2 Pre-operational Check 56 14.3 Startup Procedures SYSTEM INITIALIZE 57 STEP 4 STEP 5 * 58 14.4 Switch Power Supply (UPSBypass) 59 14.5 Stop Page 61 14.7 Changing Between Float Charge and Equalize Charge 62 14.8 Changing to Float Charge from Protection Charge (If applicable) 63 14.9 Emergency Power Off (EPO) 1. 2. 15 Troubleshooting 15.1 Types of Errors 64 15.2 Faults and Warnings Data Screen 65 15.3 LCD Fault & Warning Displays 66 15.4 Fault Messages Page 68 15.5 LCD Scroll (w/ faults or warnings) 69 15.6 Restoring UPS Operation