Toshiba AD268 64

64 Analog I/O Modules (AD268 / DA264 / TC218)

3. Input Type Setting PART 3 TC218

3. Input Type Setting

The TC218 supports multiple input types, type K, type J, type E, or ±100mV. The input type is

selected by jumper plug setting and the parameter writing by the T2 program.

Note that the input type can be selected either one, type K, type J, type E, or ±100mV, for all

channels. Any mixture settings among the channels are not allowed.

The general flow for setting the input type is as follows.

(1) Set the jumper plugs to select thermocouple input or mV input.

(2) Mount the TC218 onto the T2 rack.

(3) Turn on power to the T2 system.

(4) Execute I/O allocation.

(5) Program the "input type setting program". (see the next page)

(6) Turn the T2 to RUN mode.

(7) Cycle power off/on

3.1 Jumper plug setting

8 jumper plugs are provided on the TC218 board.

The jumper plug setting is for selecting either thermocouple input or mV input.

Jumper plugs (JP1 to JP8)

1

3

Set all the jumper plugs either side 1 or 3.

Side 1: Thermocouple input

Side 3: ±100mV input

The factory setting is ±100mV input (side 3).

•Use a pair of tweezers to set the jumper plug.

•Pay attention not to touch the components on the

board other than the jumper plug.

CTi Automation - Phone: 800.894.0412 - Fax: 208.368.0415 - Web: www.ctiautomation.net - Email: info@ctiautomation.net

Contents

Main Important Information Safety Precautions Safety Symbols ! ! Safety Precautions 2 About This Manual About This Manual Related Manual Table of Contents Part 1 8 Channel Analog Input Module AD268 4 Part 2 4 Channel Analog Output Module DA264 Part 3 8 Channel Thermocouple Input Module TC218 Page Page 8 1. Introduction 1.1 AD268 Functions Page 10 2. Specifications Users Manual 11 12 3. Input Type Setting 3. Input Type Setting 3.1 Jumper plug setting 1 3 3.2 Parameter setting by software 14 4. Wiring AD268 terminal block Users Manual 15 Voltage input External 24Vdc power supply Current input 16 4. Wiring Page 18 5.2 A/D conversion data Users Manual 19 5V range: 0 D = 3200 A 20 0 to 10V range: D = 3200 A Page 22 1 to 5V / 4 to 20mA range: 4 to 20mA range: D = 800 A - 3200 1 to 5V range: D = 3200 A - 3200 Page 24 6. Parameters The contents of the AD268's buffer memory are as follows. Users Manual 25 26 Page 28 Page 30 6.2 Parameter setting procedure 6.3 Sample program for se tting the parameters 32 7. Troubleshooting Users Manual 33 Page Page 36 1. Introduction 1.1 DA264 Functions Page 38 2. Specifications Users Manual 39 40 3. Output Type Setting 3. Output Type Setting 3.1 Parameter setting by software Users Manual 41 DA264 terminal block 42 4. Wiring External 24Vdc power supply Voltage output Current output Page 44 5.2 D/A conversion data 46 5V range: Users Manual 47 0 to 10V range: 48 0 to 5V / 0 to 20mA range: 0 to 20mA range: A = 1.25 D 0 to 5V range: Users Manual 49 1 to 5V / 4 to 20mA range: 4 to 20mA range: A = 1.25 D + 4000 1 to 5V range: A = 0.3125 D + 1000 50 Page 52 6. Parameters Page 54 6. Parameters 6.2 Sample program to access the parameters 56 7. Troubleshooting Page Page Page 60 1. Introduction 1.1 TC218 Functions Page 62 2. Specifications Users Manual 63 64 3. Input Type Setting 3. Input Type Setting 3.1 Jumper plug setting 1 3 3.2 Parameter setting by software 66 4. Wiring TC218 terminal block Users Manual 67 100mV input (CH1 to CH8) Thermocouple input CH1 CH2 to CH8 Connect the thermistor attached to the TC218 68 4. Wiring Page 70 5.2 A/D conversion data Users Manual 71 Thermocouple (type K) input: 72 Thermocouple (type J) input: Users Manual 73 Thermocouple (type E) input: 74 Users Manual 75 The contents of the TC218's buffer memory are as follows. 76 Page 78 Page 80 6.2 Parameter setting procedure 82 6.3 Sample program for se tting the parameters Page 84 7. Troubleshooting