33-EN

SMMS-i

Installation Manual

„Full opening of the valve

Open the valves of the outdoor unit fully.

MAP080

 

MAP140

 

 

MAP100

 

 

 

 

MAP160

 

 

MAP120

 

 

 

 

 

 

 

Packed valve

Ball valve

 

 

 

Using a 4mm-hexagonal wrench,

Using a flathead screwdriver, turn it counterclockwise by 90° until it hits the

fully open the valve rods.

stopper. (Full open)

 

 

 

 

Service

 

Position of screwdriver slot

 

 

 

 

 

port

Valve unit

Fully closed

Fully opened

 

 

 

 

Using flathead

Liquid side

screwdriver, turn it

counterclockwise by

(1)

90° until it hits the

 

stopper. (Full open)

(2)

Slot

 

Flare nut

* When opened fully, do not apply

 

excessive torque after the screwdriver hits

 

the stopper; otherwise a problem may be

 

caused on the valve. (5 N•m or less)

Balance pipe

Balance packed valve

 

Using a 4mm-hexagonal wrench, fully open the valve rods.

Ball valve

Using a minus screwdriver, turn it counterclockwise by 90° until it hits the stopper. (Full open)

Gas side

Fully closed

Fully opened

– 17 –

34-EN

SMMS-i

Installation Manual

„F-GAS label

This product contains fluorinated greenhouse gases covered by the Kyoto Protocol

Chemical Name of Gas

R410A

Global Warming Potential (GWP) of Gas

1975

CAUTION

1.Stick the enclosed refrigerant label adjacent to the charging and/or recovering location.

2.Clearly write the charged refrigerant quantity on the refrigerant label using indelible ink. Then, place the included transparent protective sheet over the label to prevent the writing from rubbing off.

3.Prevent emission of the contained fluorinated greenhouse gas. Ensure that the fluorinated greenhouse gas is never vented to the atmosphere during installation, service or disposal. When any leakage of the contained fluorinated greenhouse gas is detected, the leak shall be stopped and repaired as soon as possible.

4.Only qualified service personnel are allowed to access and service this product.

5.Any handling of the fluorinated greenhouse gas in this product, such as when moving the product or recharging the gas, shall comply under (EC) Regulation No. 842/2006 on certain fluorinated greenhouse gases and any relevant local legislation.

6.Periodical inspections for refrigerant leaks may be required depending on European or local legislation.

7.Contact dealers, installers, etc., for any questions.

 

 

 

 

 

 

Pre-charged Refrigerant at Factory [kg],

R410A

 

 

specified in the nameplate

 

 

 

 

 

kg

Additional Charge on Installation Site

 

 

 

 

 

 

 

 

 

 

 

kg

[kg]

 

 

 

 

 

 

 

 

 

 

 

 

kg

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

„Heat insulation for pipe

Apply heat insulation of pipe separately at the liquid, gas, and balance sides.

Be sure to use thermal insulator resistant up to 120°C or higher for pipes at the gas side.

„Finishing after connecting pipes

After piping connection work has been finished, cover the opening of the piping/wiring panel with the piping cover, or fill silicon or putty into the space between the pipes.

In case of drawing-out the pipes downward or sideward, also close the openings of the base plate and the side plate.

Under the opened condition, a problem may be caused due to the entering of water or dust.

Page 18
Image 18
Toshiba MMY-MAP1204HT8-E, MMY-MAP1604HT8ZG-E „ Full opening of the valve, „ F-GAS label, „ Heat insulation for pipe

MMY-MAP0804HT8-E, MMY-MAP1604HT8Z-E, MMY-MAP1404HT8-E, MMY-MAP0804HT8Z-E, MMY-MAP1204HT8Z-E specifications

The Toshiba MMY-MAP0804HT8Z-E, MMY-MAP1404HT8-E, MMY-MAP1604HT8Z-E, MMY-MAP0804HT8-E, and MMY-MAP1604HT8-E are part of Toshiba's advanced air conditioning line-up, designed for both residential and commercial applications. These models are engineered to offer high efficiency, comfort, and reliability, making them an excellent choice for modern HVAC solutions.

One of the standout features of these models is their high Seasonal Energy Efficiency Ratio (SEER), which indicates their superior energy performance. They are built to reduce energy consumption while providing optimal cooling and heating capabilities. This is particularly beneficial for users looking to lower their energy bills without sacrificing comfort.

In terms of technology, Toshiba incorporates inverter technology in these air conditioning units. The inverter system adjusts the compressor's speed according to the cooling demand, ensuring consistent temperatures and enhanced energy savings. This feature is especially useful during peak usage periods, as it minimizes energy spikes associated with traditional on/off systems.

Additionally, the MMY-MAP series includes sophisticated air filtration systems that improve indoor air quality. These filters capture dust, allergens, and other pollutants, creating a healthier living or working environment. The units also come equipped with a quiet operation mode, allowing them to function with minimal noise – a crucial aspect for residential settings and quiet commercial spaces.

These models boast a sleek and compact design, making them easy to install in various configurations. Their aesthetic appeal ensures they blend seamlessly with any interior decor. Furthermore, they are built to withstand diverse environmental conditions, with robust materials that ensure durability and longevity.

User-friendly controls are another hallmark of the Toshiba MMY-MAP series. Many of these models support smart technology, allowing for remote operation via smartphones or tablets. This capability enhances convenience, enabling users to monitor and adjust settings in real-time.

In summary, the Toshiba MMY-MAP0804HT8Z-E, MMY-MAP1404HT8-E, MMY-MAP1604HT8Z-E, MMY-MAP0804HT8-E, and MMY-MAP1604HT8-E models epitomize efficiency and comfort. With their energy-saving features, advanced inverter technology, effective air filtration, and smart connectivity, these air conditioning units are designed to meet the demands of modern users, ensuring a comfortable and healthy indoor environment all year round.