Convection System, Blower Motor | Turbo Chef Technologies 2020

2 4 OVEN SYSTEMS

Accessing Parameters

WARNING: DO NOT perform this procedure unless instructed by TurboChef. Changing the parameters to other than those preset by TurboChef can damage critical oven components.

NOTE: “Motor Rated Speed” (07) is RPM of motor before gearbox, not after.

1.Open the right end bell (page A-8).

2.Locate the CMSC (page A-8).

3.Press the M key.

4.Use the and keys to navigate the parameters. See page 40.

5.Press the M key to access the parameter shown on the CMSC display.

6.Use the and keys to manipulate the parameter.

7.Press the M key to return to the parameter selection.

8.Repeat steps 4-7 to manipulate other parameters as needed.

3.Take a resistance reading of the motor windings and use Figure 34 to verify the resistance readings are correct.

4.If the resistance readings are correct, reconnect motor wiring and then apply line voltage to the unit and check for voltage applied to the motor windings.

5.If no voltage is present, ensure the BMSC is operating properly (see below).

6.If BMSC is operating properly, inspect the wire harness for damage or shorts (pages 37-38).

7.If wire harness is intact and undamaged and the BMSC is operating properly, the blower motor is damaged or defective and must be replaced (page A-7 = lower, A-8 = upper).

Blower Motor Speed Controller (BMSC)

The motor controller is proprietary and will only operate the convection motor described above. The motor controller is controlled on command from the I/O control board and a 0-10VDC speed command from the I/O control board. See pages 27-28 for troubleshooting.

The Convection System

This section contains information about and testing procedures for the following components:

-Blower Motor

-Blower Motor Speed Controller (BMSC)

-Heaters

Blower Motor

The convection motor is a brushless AC switch reluctance type. Its top speed is 7100 RPM at 1 HP. The motor is controlled by a proprietary controller.

Testing Procedure

1.Disconnect line voltage from the unit.

2.Make sure the motor spins freely.

Heaters

The back and front convection heaters are rated at 6750 watts at 208 VAC with a resist- ance of 14.4 Ohms. The heaters are controlled by the K4/K5 solid state relay and can be tested in TEST MODE (see page 17).

To	From	Description	Expected Resistance
Black	Brown	Winding (A-B)	2.3-2.8 W

Black	White	Winding (A-C)	2.3-2.8 W

Red	White	Winding (B-C)	2.3-2.8 W

N/A	Green	Windings to	Open
N/A	Green	chassis	Open
		chassis

Figure 34: Blower Motor Ohm Chart (Motor Windings)

2020 specifications

Turbo Chef Technologies 2620,2020 is a revolutionary cooking appliance that merges advanced technology with user-friendly operation. Designed for commercial kitchens, it stands out as a versatile solution for various cooking methods, meeting the demands of fast-paced environments while ensuring consistent results.

One of the main features of the Turbo Chef 2620 is its innovative cook technology that incorporates a combination of convection, microwave, and radiant heat. This tri-technology system allows food to be cooked quickly and evenly, which not only saves time but also enhances the quality of the final product. The appliance employs a patented air impingement system, ensuring that heat circulates uniformly around the food. This results in crispy exteriors and moist interiors, making it ideal for items like pizza, baked goods, and meats.

In addition to its cooking capabilities, the Turbo Chef 2620 is equipped with a user-friendly digital control panel. The intuitive interface allows for easy programming and access to a variety of cooking presets, making it accessible even for inexperienced staff. Operators can store multiple cooking profiles, streamlining operations and improving efficiency. The appliance also features a robust construction, built to withstand the demands of high-volume use, ensuring durability and longevity in busy kitchen settings.

Another significant characteristic of the Turbo Chef 2620 is its energy efficiency. The appliance is designed to minimize energy consumption without sacrificing performance, making it an environmentally friendly choice for commercial kitchens. Its compact size allows for flexible placement, making it suitable for establishments with limited space.

Furthermore, the Turbo Chef 2620 ensures food safety and ease of maintenance. The appliance's design includes removable components that facilitate easy cleaning, while essential safety features protect users during operation.

Overall, Turbo Chef Technologies 2620,2020 is a groundbreaking appliance that offers an impressive array of features and technologies for modern cooking needs. With its advanced cooking capabilities, user-friendly operation, energy efficiency, and robust design, it represents an ideal solution for any commercial kitchen looking to enhance productivity while maintaining high food quality.

Turbo Chef Technologies 2020 manual Convection System, Blower Motor Speed Controller Bmsc, Heaters

Models: 2020