Manuals / Wayne-Dalton / Household Appliance / Garage Door Opener

Wayne-Dalton 3320B, 3324B, 3322B-Z, 3224C-Z, 3222C, 3220C Wired Infrared Safety Sensor Installation

Models: 3320B-Z 3221C 3220C-Z 3222C-Z 3220C 3320B 3322B 3224C 3324B 3224C-Z 3221C-Z 3322B-Z 3222C

1 48

Download 48 pages 15.14 Kb

Page 15

11

Tools Needed:

Ratchet Wrench

Tape Measure

Power Drill

3/16” Drill Bit

7/16” Socket

Driver

7/16” Wrench

Pencil

Wired Infrared Safety Sensor

Installation

IMPORTANT: BOTH WALL BRACKETS MUST BE MOUNTED AT THE SAME HEIGHT FOR PROPER ALIGNMENT.

Note: Use Steps a-c for installing sensors on both sides of the garage door.

a. Select and mark with a pencil, a mounting location no more than

5 inches above the floor to center line of wall mounting bracket. The safety sensors should be mounted as close to the door track or inside edge of the door as possible to offer maximum entrapment protection. It is very important that both wall mounting brackets be mounted at the same height for proper alignment.

b. Drill pilot holes, using a 3/16” drill bit. Using two 5/16” x 1-1/2” lag screws, permanently mount the wall mounting brackets to both door jambs. In some installations it may be necessary to attach a wooden spacer to the wall to achieve the required alignment.

Wall Mounting Bracket

5”

a
b	Door Jam
		5/16” x 1-1/2”
	Wall Mounting	Lag Screw
	Wall Mounting
	Bracket
	Nut

Attach the “U” brackets to the wall mounting brackets with 1/4”-20 x 1/2” carriage bolts, washers and nuts. Insert the bolts from the inside of the “U” bracket and hand-tighten.

IMPORTANT: IDENTIFY WHICH SIDE OF THE GARAGE DOOR IS EXPOSED TO THE MOST SUNLIGHT. MOUNT THE SENDING UNIT (UNIT WITHOUT LED) ON THE SIDE WHICH IS EXPOSED TO THE MOST SUN. SUNLIGHT MAY AFFECT THE SAFETY SENSORS, AND THIS ORIENTATION WILL HELP REDUCE THE EFFECT.

c. Attach the sending and receiving safety sensors to the “U” brackets by inserting all three tabs into the respective holes.

Washer

1/4”-20 x 1/2” Carriage Bolt

c

U-Bracket

Receiving	LED
Unit

Please Do Not Return This Product To The Store. Call Us Directly! Our Trained Technicians Will Answer Your Questions and/or Ship Any Parts You May Need 9 You can reach us Toll Free at 1-888-827-3667 for Consumer Assistance or online at www.wayne-dalton.com

Image 15

Wayne-Dalton 3324B, 3322B-Z, 3224C-Z, 3222C-Z, 3220C-Z, 3221C-Z, 3320B-Z Wired Infrared Safety Sensor Installation

Contents

Important Notice Garage Doors & OpenersRev.3 7/19/2007 Package Contents Page Door Test Two Pre-InstallationDisconnect from power source and proceed to assembly Door Test One System Features Tools NeededHomelink Compatibility Rolling Code Technology Deﬁnition of key words used in this manual Table of Contents Attaching Opener to Rail Installation Positioning and Installing Front Wall Bracket Service PersonReinforce the Header Wall AT Least 3 Feet Long Positioning MotorEnd of Opener Attach Unit to Front Wall Bracket Mounting Opener End Proper Installation Reinforcing of Your Door Installing LightMounting Door Bracket Manufacturer for Proper Garage Door Wired Wall Station Installation If IncludedDoor can be Seen When Wall Station Near or Next to Children and in a Location Where Wall Station Installation If IncludedWall Station Near or Next to Garage Door Wall Station OUT of the Reach Entrapment Apply entrapment warning label in aNot adhere Wired Infrared Safety Sensor Installation Sensor to Opener Installation of Wiring for WiredInfrared Safety Sensor Connecting Wired Infrared Safety Cord in Anyway Connecting OpenerConnecting Trolley To Latch Assembly Fully Closed Position Alignment of Wired InfraredSafety Sensors Be Closed by Continuously Setting Trolley Close Position ARMTo Avoid Possible Injury or Connecting Door Arm to Door Setting Door Opening Travel Setting Door Close Travel Stop Bolt Trolley Opener Contact Obstruction Test Fatal Injury MAY ResultResult from Operating the DOOR/OPENER To Prevent Door Damage or Programming Wireless KeylessEntry If Included Possible Personal Injury Materials Important Install ALL WallWood framing using the two screws Surface inside garage Instructions Illustrated Power ConnectionTo Avoid Electrical Shock Important Check Your Local 14 x 5/8 self tapping screws as shown in FIG Optional InstallationsTools Needed Power Drill Socket Driver Mounting Door Bracket To Series Door 1/4 14 x 5/8 self-tapping screws Must be Adjusted ProperlyShown in FIG With Step Standard Lift Radius Being UsedTrack LOW Headroom DIM Type of ARM Connecting Door Arm Have to cut straight arm to accomplish Trolley settingsDetermine the WAYNE-DALTON Track Radius Being Used Distance forward To Door , on LOW Headroom Trolley Positioning Chart for Operation Read and Follow ALL InstructionsDoor activation Operating the Wireless Wall Station Opener Controls Customizing the Settings Primary Programming for HomeLink to the Prodrive Programming/Training HomeLink UnitTeaching HomeLink to the opener Alternate Programming for HomeLink to the Prodrive Opening Force Adjustment AdjustmentsAdjustment # 1 Opening and Closing Force Closing Force Adjustment Tools Needed None TransmitterWall Station Maintenance Battery Replacement for Wall StationTwice a Year Troubleshooting MAINTENANCE/ TroubleshootingSymptom Probable Cause Corrective Action Parts Breakdown Rail Assembly All Models Description# Per Unit Description # Per Unit Parts Breakdown Opener Assembly And Accessories All Models Wireless Keyless Entry Prodrive Accessories Pre-drill 3/32 pilot hole Drill TemplatePre-drill 5/64 pilot hole Thank you for your purchase Please Do Not Return This Product To The Store Replacement labor Lifetime Limited Warranty FCC and IC Statement Patent Information