Wayne-Dalton 3324B, 3322B-Z, 3320B, 3224C-Z, 3222C-Z, 3220C-Z Connecting Door Arm, Top View

I		Setting Trolley Close Position/
		Connecting Door Arm
		(Models 9100, 9400, 9600, 5120, 5140 & 9700)
			With Torsion Springs
Tools Needed:	DETERMINE THE WAYNE-DALTON
	TRACK RADIUS BEING USED:
Needle Nose Pliers	FOR MOUNT HOPE AND PENSACOLA
	TRACK:
Adjustable Wrench	Measure the curved ends of the horizontal
	track to determine if you have a 12” or 15”
	radius horizontal track, as shown in FIG. 1.
Ratchet Wrench	FOR PORTLAND TRACK:
7/16” Socket	The horizontal tracks are stamped with
	radius on the side of the horizontal track, as
9/16” Socket	shown in FIG. 1.1.
	NOTE: If necessary, remove the upper arm
Hacksaw	(straight arm) from the trolley, to use the
	lower arm (curved arm). Remove the hairpin
	cotter from the clevis pin at the front of
	trolley and slide clevis pin out far enough
	to slide the upper arm out between the left
	and right side of trolley body. Position the
	lower door arm so the end with the single
	hole lines up with the clevis pin. Slide clevis
	pin completely back into trolley and reinstall
	hairpin cotter.
	LOW HEADROOM:
	If you have low headroom track, as shown
	in FIG. 1.5 on page 26, then proceed with
	“Low Headroom Trolley Positioning Charts”
	on page 26.
	STANDARD LIFT:
	Using the STANDARD LIFT TROLLEY
	POSITIONING CHARTS, refer to DIM “X”
	to set the distance from header to trolley, as
	shown in FIG. 1.2.
	NOTE: Depending on your setup, you may
	have to cut straight arm to accomplish
	trolley settings.
		STANDARD LIFT TROLLEY POSITIONING
		CHART FOR 10” AND 12” RADIUS
		FOR (MODELS 9100, 9400, 9600, 5120 & 5140)
		DIM “X”	TYPE OF ARM	REFERENCE
			BEING USED	ILLUSTRATIONS
		11 1/2”-13”	STRAIGHT /	FIG. 1.3
			CURVED
	If adjustment of the trolley position is
	required, use the close travel adjustment
	screw located on the bottom of the opener,
	as shown in FIG 1.4 on page 26. A 1/4
	turn equals approximately 1” of trolley
	travel; turn clockwise to decrease distance
	(forward) and counter-clockwise to increase
	distance (forward).
	NOTE: Proceed with “Connecting Door Arm
	To Door” Step 18, on page 14.

Horizontal

Track

	12” OR 15”	Horizontal
		Track
	FIG. 1
		12”	FIG. 1.1
	TOP VIEW
Clevis Pin	Trolley		Stamped
			Radius
			12”

Hairpin Cotter

“X”

10”, 12”, 14”, OR 15” Standard Lift Track

Top Section

FIG. 1.2

Straight Arm

Curved

Arm

Cut Straight Arm To

Accomplish Trolley

Setting

FIG. 1.3

STANDARD LIFT TROLLEY POSITIONING CHART

FOR 14” AND 15” RADIUS

(MODELS 9100, 9400, 9600, 5120 & 5140)

DIM “X”	TYPE OF ARM	REFERENCE
	BEING USED	ILLUSTRATIONS
10”-12”	STRAIGHT /	FIG. 1.3
	CURVED

STANDARD LIFT TROLLEY POSITIONING CHART

FOR (MODEL 9700) 15” RADIUS

DIM “X”	TYPE OF ARM	REFERENCE
	BEING USED	ILLUSTRATIONS
11 1/16”-	STRAIGHT /	FIG. 1.3
16 7/8”	CURVED

Please Do Not Return This Product To The Store. Call Us Directly! Our Trained Technicians Will Answer Your Questions and/or Ship Any Parts You May Need 25 You can reach us Toll Free at 1-888-827-3667 for Consumer Assistance or online at www.wayne-dalton.com