Woods Equipment M8200 Safety & Instructional Decals, Replace Immediately If Damaged, or death

SAFETY & INSTRUCTIONAL DECALS

ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!

Replace Immediately If Damaged!

(Safety Decals continued from previous page)						LOADER MOUNTING INSTRUCTIONS
6 - PN 56050					Read Operator’s Manual instructions before proceding.
						To Remove Loader
	WARNING		WARNING		1.	Park tractor on level surface with bucket flat on
						ground.
					2.	Dump bucket to take weight off mount pins and
						allow for stand installation. Set brake and shut off
						tractor.
					3.	Remove stands from crosstube and pin into brackets.
						(Pin location noted in mounting manual.)
					4.	Remove mount pins from loader upright.
					5.	Roll back bucket completely to raise uprights from
CRUSHING HAZARD						mounts.
					6.	Shut off engine. Disconnect hydraulics. Back tractor
	To avoid injury		FALLING HAZARD			away. Store mount pins in loader uprights.
						To Mount Loader
￿	or death:		To avoid injury
					1.	Remove mount pins from uprights.
	Do not walk or work un-
		￿	or death:		2.	Drive tractor into loader slowly.
￿derneath a raised loader.			Do not work from or		3.	Shut off tractor. Connect hydraulics.
	Lower loader to ground
					4.	Dump bucket to lower upright into mounts.
			allow riders on loader or
	before leaving tractor				5.	Continue dumping bucket until uprights settle into
			its attachments.
	seat.			56050-A
						mounts, pins can be installed and stands can be
						removed. Set brake and shut off tractor.
					6.	Install mount pins and clips. Remove stands and pin
5 - PN 19924						into crosstube.	56059-A
						9 - PN 56059
	￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿
			WARNING

Check for leaks with cardboard; never use hand.

Before loosening fittings: lower load, release pressure, and

￿be sure oil is cool.

19924-B Consult physician immediately if skin penetration occurs.

8 - PN 45002 (WHEN EQUIPPED)

WARNING

LOADER ATTACHMENT CAN FALL OFF IF NOT PROPERLY ATTACHED.

Read operator’s manuals for instructions.

￿Position and align loader to attachment.

Rotate coupler handles to full locked position. Lockpins must fully extend and engage into attachment retaining slots.

Attachment mechanism must be functional and in good repair.

￿Only use loader manufacturer approved attachments.

For information on approved attachments, call 1-800-319-6637.

Failure to follow these instructions can result in serious injury or death. 56055-B

7 - PN 56055

10 - PN 56889

8 - PN 260274

(WHEN EQUIPPED)

(WHEN EQUIPPED)

11 - PN 45024

￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿WARNING￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿

Only use loader manufacturer approved attachments.
Failure to do so can cause serious injury or death.	45024-A

￿￿￿￿￿￿￿ 56889

￿￿￿￿￿￿￿ 260274-C

PN-46018 (Rev. 11/10/00)

SAFETY 5