Lubrication Points | Woods Equipment S22CD, S20CD, S15CD, S27CD, S25CD

Figure 22. PTO Driveline Lubrication Points

A. Daily or 8 hours

B. 25 hours

C. 40 hours

D. Check Daily/Change Annually

Figure 23. Lubrication Points

(Rev. 1/24/2011) MAN0506 (Rev. 9/5/2008)

Service & Maintenance 25

Image 25

Woods Equipment S22CD, S20CD, S15CD, S27CD, S25CD manual Lubrication Points

Contents

Flail Shredder Introduction LEA EL Instructivo Table of Contents Specifications General Information Balance Statement Preparation Safety RulesTraining Transportation Operation Maintenance Storage Replace Immediately If Damaged Safety & Instructional Decals Peligro Be Careful Advertencia Operator SIGN-OFF Record Operator Record Principal Components OperationBREAK-IN of the Flail Shredder After operating for 1/2 hour Tractor Weight HorsepowerPRE-OPERATION Check List Choosing the Correct Tractor PTO Driveline Length With Quick Hitch Attachment Attaching Shredder to TractorCut only the male end. Never cut the female end Pull-Type Model Without Quick Hitch AttachmentAttach PTO Driveline Attach Hydraulics Center Cutter Option Removing Shredder from Tractor Raise StandsPreparing for Operation Flail Height Point Hitch Models SET Operating HeightPull-Type Models Point & 2-Point Hitch Models Setting Outer Trailing Wheels Casters & Struts Setting Flail HeightStarting the Tractor Stopping the Tractor Hazard Area CleaningGround Speed Turning Additional Rear Wheels Rubber FlapsBED Cones Lubricants Service & MaintenanceGreasing Lubrication Schedule Lubrication Points Every 25 hours of operation Daily or every 8 hours of operationEvery 40 hours of operation Annually Gearbox OIL Leakage Lubrication Service Record Hours Serviced byHours or daily Hours Changing Gearbox OIL Gearbox leakage & Troubleshooting Wheel Spacing Ratchet Height AdjustmentReplacing Flail Knives Servicing Rotors Flail Tubes Replacing Rubber Shield Flaps Replacing Components Removing Components Servicing Weasler Modular Friction Clutch Replacing Stub ShaftBreaking In the Clutch Run Removing the Driveline Rebuilding Overrunning Clutch Rebuilding Friction PackMounting Clutch to Shredder Service & Maintenance Problem Cause Solution Troubleshooting Worksheet for Contour Flail Patterns 24’ Wheel Assembly AssemblyDealer SET-UP Instructions For Some Models Shipped on End ALL Units PULL-TYPE Hitch InstallationPull-type units only Optional Equipment Rubber Belting Installation Manual Storage Tube InstallationRubber Flap Installation Safety Light KIT Installation Safety Light Kit Diagram Non-End Tow Install Center Deflector Block Shredded Center CUT KIT InstallationAssemble Motor and Blade Assembly Hoses Install Motor Housing Install Decals Install Hose ClampsConnect Hoses to Tractor Remove Deflector Kit PRE-DELIVERY Check List Dealer Check ListsDelivery Check List Dealer Check Lists Parts Index Flail Shredder Center Drive Flail Shredder Frame Assembly Part QTY Description Center Drive Flail Shredder Frame Assembly Parts List Left Right Flail Tube Assembly Ting BED Cone Assembly Optional Parts Dual Safety Light KIT Optional Weasler Automatic Clutch Optional Weasler 24K Torqmaster Clutch Assembly Weasler 30K 3-POINT PTO Shaft with Automatic Clutch Optional 1019820 Center Drive Gearbox Rubber Belting Center Cutter KIT Optional Advertencia Center Deflector Optional Center Cutter KIT Parts List Rubber Flap SAE Series Torque Chart Bolt Torque ChartMetric Series Torque Chart Abbreviations Bolt Size Chart Index Assembly Warranty Rev /3/2011 South Illinois Route Post Office Box Oregon, Illinois Woods Equipment Company