Flail Tube Assembly, Left Right | Woods Equipment S22CD, S20CD

FLAIL TUBE ASSEMBLY

REF	LEFT	RIGHT	QTY	DESCRIPTION
REF	PART #	PART #	QTY	DESCRIPTION
1	1016199LK 1016198LK		1	15’ Flail tube w/knives
1	1016199HD 1016198HD		1	15’ HD Cotton tube
				w/knives
1	1016199CP 1016198CP		1	15’ Cup knife tube
				w/knives
1	1013109LK 1013108LK		1	20’ Flail tube w/knives
1	1013109HD 1013108HD		1	20’ HD Cotton tube
				w/knives
1	1013109CP 1013108CP		1	20’ Cup knife tube
				w/knives
1	1016179LK 1016178LK		1	22’ Flail tube w/knives
1	1016179HD 1016178HD		1	22’ HD Cotton tube
				w/knives
1	1016179CP 1016178CP		1	22’ Cup knife tube
				w/knives
1	1012169LK 1012168LK		1	25’ Flail tube w/knives
1	1012169HD 1012168HD		1	25’ HD Cotton tube
				w/knives
1	1012169CP 1012168CP		1	25’ Cup knife tube
				w/knives
1	1013119LK 1013118LK		1	27’ Flail tube w/knives
1	1013119HD 1013118HD		1	27’ HD Cotton tube
				w/knives
1	1013119CP 1013118CP		1	27’ Cup knife tube
				w/knives

REF	PART	QTY	DESCRIPTION
2	1012163	2	Stub shaft, 2-3/16"
3	50531067	AR	L-Knife, long 8-1/2", (6 mm)

31019788 AR L-Knife, HD cotton (Durafaced) (8 mm)

450531048 AR Weld-on clip

5	50030779		12	3/8 High collar lock washer
6	1010056		AR	L- Knife, cut off
6	1019789		AR	L- Knife, cut off
7	50030345		2	Drive hub sleeve, outer
8	1013092		12	3/8 NC x 2-1/2 SHCS
9	90002526		6	1/2 NC x 2-3/4 Tap bolt, full thread
10	90515001	*	2	1/8 NPT Straight grease fitting
11	1012164		2	2-7/16 Hub, E-style
12	90001357	*	AR	5/8 NC x 3-1/2 Hex bolt GR5
13	50530405		AR	Hardened wear bushing

1450530974 AR Steel cup flail 11" (Standard)

1450530973 AR Steel cup flail 9"

1450530972 AR Steel cup flail short

1590011013 * AR 1/2 Lock washer

16	11900 * AR 1/2 NC Flange lock nut

1790006508 AR 5/8 NC Top lock nut

1890011015 * AR 5/8 Lock washer

19 1010061 AR Spacer, steel (for 6 mm L-knife)

191012184 AR Spacer, steel (for 8 mm L-knife)

201010062 AR Bushing, L-knife

21 90001758	*	AR 1/2 NC x 3-1/4 Carriage bolt
SHCS		Socket Head Cap Screw
NS		Not Shown
AR		As Required
*		Standard hardware, obtain locally

50 Parts	MAN0506 (Rev. 9/5/2008)

Image 50

Woods Equipment S22CD, S20CD, S15CD, S27CD, S25CD manual Flail Tube Assembly, Left Right

Contents

Flail Shredder Introduction Table of Contents LEA EL Instructivo Specifications Balance Statement General Information Training Safety RulesPreparation Operation Transportation Maintenance Storage Safety & Instructional Decals Replace Immediately If Damaged Peligro Advertencia Be Careful Operator Record Operator SIGN-OFF Record BREAK-IN of the Flail Shredder OperationPrincipal Components After operating for 1/2 hour PRE-OPERATION Check List HorsepowerTractor Weight Choosing the Correct Tractor PTO Driveline Length Cut only the male end. Never cut the female end Attaching Shredder to TractorWith Quick Hitch Attachment Attach PTO Driveline Without Quick Hitch AttachmentPull-Type Model Attach Hydraulics Center Cutter Option Preparing for Operation Raise StandsRemoving Shredder from Tractor Flail Height Pull-Type Models SET Operating HeightPoint Hitch Models Point & 2-Point Hitch Models Starting the Tractor Setting Flail HeightSetting Outer Trailing Wheels Casters & Struts Stopping the Tractor Ground Speed CleaningHazard Area Turning BED Cones Rubber FlapsAdditional Rear Wheels Greasing Service & MaintenanceLubricants Lubrication Schedule Lubrication Points Every 40 hours of operation Daily or every 8 hours of operationEvery 25 hours of operation Annually Hours or daily Lubrication Service Record Hours Serviced byGearbox OIL Leakage Hours Gearbox leakage & Troubleshooting Changing Gearbox OIL Replacing Flail Knives Ratchet Height AdjustmentWheel Spacing Replacing Rubber Shield Flaps Servicing Rotors Flail Tubes Removing Components Replacing Components Breaking In the Clutch Run Replacing Stub ShaftServicing Weasler Modular Friction Clutch Removing the Driveline Mounting Clutch to Shredder Rebuilding Friction PackRebuilding Overrunning Clutch Service & Maintenance Troubleshooting Problem Cause Solution Worksheet for Contour Flail Patterns 24’ Dealer SET-UP Instructions AssemblyWheel Assembly For Some Models Shipped on End Pull-type units only PULL-TYPE Hitch InstallationALL Units Rubber Flap Installation Manual Storage Tube InstallationOptional Equipment Rubber Belting Installation Safety Light KIT Installation Install Center Deflector Safety Light Kit Diagram Non-End Tow Assemble Motor and Blade Center CUT KIT InstallationBlock Shredded Install Motor Housing Assembly Hoses Connect Hoses to Tractor Install Hose ClampsInstall Decals Remove Deflector Kit Delivery Check List Dealer Check ListsPRE-DELIVERY Check List Dealer Check Lists Parts Index Flail Shredder Center Drive Flail Shredder Frame Assembly Center Drive Flail Shredder Frame Assembly Parts List Part QTY Description Flail Tube Assembly Left Right Ting BED Cone Assembly Optional Parts Dual Safety Light KIT Optional Weasler 24K Torqmaster Clutch Assembly Weasler Automatic Clutch Optional Weasler 30K 3-POINT PTO Shaft with Automatic Clutch Optional 1019820 Center Drive Gearbox Rubber Belting Advertencia Center Cutter KIT Optional Center Cutter KIT Parts List Center Deflector Optional Rubber Flap Metric Series Torque Chart Bolt Torque ChartSAE Series Torque Chart Bolt Size Chart Abbreviations Assembly Index Warranty Rev /3/2011 Woods Equipment Company South Illinois Route Post Office Box Oregon, Illinois