Rubber Belting | Woods Equipment S25CD, S22CD, S20CD, S15CD, S27CD

RUBBER BELTING

REF	PART	QTY	DESCRIPTION	REF	PART		QTY	DESCRIPTION
1	1012202	4	Rubber belting (15 ft)	5	64824	*	34	3/8 NC x 1-1/2 Carriage bolt (15 ft)
1	1012202	6	Rubber belting (20 ft & 22 ft)	5	64824	*	46	3/8 NC x 1-1/2 Carriage bolt (20 ft)
1	1012202	8	Rubber belting (25 ft & 27 ft)	5	64824	*	50	3/8 NC x 1-1/2 Carriage bolt (22 ft)
2	1022647	4	Belt bar (15ft)	5	64824	*	62	3/8 NC x 1-1/2 Carriage bolt (25 ft)
2	1022647	6	Belt bar (20 ft & 22 ft)	5	64824	*	34	3/8 NC x 1-1/2 Carriage bolt (27 ft)
2	1022647	8	Belt bar (25 ft & 27 ft)	6	14350	*	34	3/8 NC flange lock nut (15 ft)
3	1022649	2	Belt bar (15 ft & 27 ft)	6	14350	*	46	3/8 NC flange lock nut (20 ft)
3	1022648	2	Belt bar (20 ft)	6	14350	*	50	3/8 NC flange lock nut (22 ft)
3	1022650	2	Belt bar (22 ft)	6	14350	*	26	3/8 NC flange lock nut (25 ft)
4	1016188	2	Rubber belting (15 ft & 27 ft)	6	14350	*	62	3/8 NC flange lock nut (27 ft)
4	1016195	2	Rubber belting (20 ft)
4	1019763	2	Rubber belting (22 ft)		* Standard hardware, obtain locally

MAN0506 (Rev. 9/7/2011)	Parts 59

Image 59

Woods Equipment S25CD, S22CD, S20CD, S15CD, S27CD manual Rubber Belting

Contents

Flail Shredder Introduction LEA EL Instructivo Table of Contents Specifications General Information Balance Statement Training Safety RulesPreparation Transportation Operation Maintenance Storage Replace Immediately If Damaged Safety & Instructional Decals Peligro Be Careful Advertencia Operator SIGN-OFF Record Operator Record After operating for 1/2 hour OperationPrincipal Components BREAK-IN of the Flail Shredder Choosing the Correct Tractor HorsepowerTractor Weight PRE-OPERATION Check List PTO Driveline Length Cut only the male end. Never cut the female end Attaching Shredder to TractorWith Quick Hitch Attachment Attach Hydraulics Center Cutter Option Without Quick Hitch AttachmentPull-Type Model Attach PTO Driveline Flail Height Raise StandsRemoving Shredder from Tractor Preparing for Operation Point & 2-Point Hitch Models SET Operating HeightPoint Hitch Models Pull-Type Models Stopping the Tractor Setting Flail HeightSetting Outer Trailing Wheels Casters & Struts Starting the Tractor Turning CleaningHazard Area Ground Speed BED Cones Rubber FlapsAdditional Rear Wheels Lubrication Schedule Service & MaintenanceLubricants Greasing Lubrication Points Annually Daily or every 8 hours of operationEvery 25 hours of operation Every 40 hours of operation Hours Lubrication Service Record Hours Serviced byGearbox OIL Leakage Hours or daily Changing Gearbox OIL Gearbox leakage & Troubleshooting Replacing Flail Knives Ratchet Height AdjustmentWheel Spacing Servicing Rotors Flail Tubes Replacing Rubber Shield Flaps Replacing Components Removing Components Removing the Driveline Replacing Stub ShaftServicing Weasler Modular Friction Clutch Breaking In the Clutch Run Mounting Clutch to Shredder Rebuilding Friction PackRebuilding Overrunning Clutch Service & Maintenance Problem Cause Solution Troubleshooting Worksheet for Contour Flail Patterns 24’ For Some Models Shipped on End AssemblyWheel Assembly Dealer SET-UP Instructions Pull-type units only PULL-TYPE Hitch InstallationALL Units Safety Light KIT Installation Manual Storage Tube InstallationOptional Equipment Rubber Belting Installation Rubber Flap Installation Safety Light Kit Diagram Non-End Tow Install Center Deflector Assemble Motor and Blade Center CUT KIT InstallationBlock Shredded Assembly Hoses Install Motor Housing Remove Deflector Kit Install Hose ClampsInstall Decals Connect Hoses to Tractor Delivery Check List Dealer Check ListsPRE-DELIVERY Check List Dealer Check Lists Parts Index Flail Shredder Center Drive Flail Shredder Frame Assembly Part QTY Description Center Drive Flail Shredder Frame Assembly Parts List Left Right Flail Tube Assembly Ting BED Cone Assembly Optional Parts Dual Safety Light KIT Optional Weasler Automatic Clutch Optional Weasler 24K Torqmaster Clutch Assembly Weasler 30K 3-POINT PTO Shaft with Automatic Clutch Optional 1019820 Center Drive Gearbox Rubber Belting Center Cutter KIT Optional Advertencia Center Deflector Optional Center Cutter KIT Parts List Rubber Flap Metric Series Torque Chart Bolt Torque ChartSAE Series Torque Chart Abbreviations Bolt Size Chart Index Assembly Warranty Rev /3/2011 South Illinois Route Post Office Box Oregon, Illinois Woods Equipment Company