LEFT-TILT Table SAW | Woodstock W1677, W1711 instruction

MODEL W1677/W1711 SERIES

LEFT-TILT TABLE SAW

W1677EXT1 Shown

OWNER'S MANUAL

Phone: (360) 734-3482 • Online Technical Support: tech-support@shopfox.biz

COPYRIGHT © JULY, 2002 BY WOODSTOCK INTERNATIONAL, INC. REVISED MAY, 2007 (TR).

	WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT
#5674TR	THE WRITTEN APPROVAL OF WOODSTOCK INTERNATIONAL, INC.	Printed in Taiwan
#5674TR		Printed in Taiwan

Image 1

Woodstock W1677, W1711 owner manual LEFT-TILT Table SAW

Contents

LEFT-TILT Table SAW Page Table of Contents Woodstock Technical Support Introduction W1677 Series Specifications W1711 Series Specifications Fence controls Blade Guard/Splitter Miter Gauge Controls and Features Standard Safety Instructions Safety Always Lock Mobile Bases if Used Before Operating Machinery Specific Safety Instructions for Table Saws Unplug saw before changing blades Avoiding Potential Injuries Use featherboards when possible To protect against kickback Use a zero-clearance table insert whenever possible Kickback Common Terms 220V Operation ElectricalExtension Cords Grounding Unpacking SetupInventory Box Inventory Figures 12 Qty Inventory Needed for Your Saw Shop Fox Classic Fence InventoryStandard Rails Figure Qty Long Rails Figure Qty Flat Washers 3⁄ 8 Rail/Ext Table Shop Fox Original Fence Inventory Cleaning Machine Machine Placement Mobile Base AssemblyTo assemble your table saw, do these steps Motor shipping brace Installing blade Adjusting table insert flush Before you test run the machine, do these steps Test RunTo test run the table saw, do these steps General OperationsBlade Height Feed Rate Blade Material Blade SelectionBlade Types To change blades, do these steps Changing Blades Through Cuts Through vs. Non-Through CutsNon-Through Cuts Rip Cuts When using the tilting mechanismBlade Tilt/Bevel Cuts To make a rip cut, do these steps Cross Cuts To crosscut using the miter gauge, do these stepsMiter Cuts To cut a miter, do these steps To use a stacked or wobble dado blade, do these steps Dado Cuts To cut dadoes with a standard blade, do these steps First cut when making a dado With a standard ripping blade To cut rabbets with the dado blade, do these steps Rabbet Cuts Clearly mark the width of the rabbet cut on Workpiece To cut rabbets with the standard blade, do these steps Resaw Barrier ResawingComponents Needed for the Resaw Barrier To build the resaw barrier, do these steps Components Needed for the Auxiliary Fence Auxiliary FenceTo build the auxiliary fence, do these steps Components Needed for Resawing Resawing OperationsTo perform resawing operations, do these steps Outfeed roller table Aftermarket Safety Accessories Here are some of the basic items you may want to consider Shop-Made Safety Accessories Cleaning MaintenanceBelts Table & Base Blade Tilt Stop Bolts ServiceTo set the stop bolts on the trunnion, do these steps To adjust the geared bearing housing, do these steps To adjust the trunnion assembly, do these stepsBlade Alignment Measuring blade to miter slot Miter Slot Parallel to Blade To shim an extension wing, do these steps Shimming Wings To check and align the splitter to the blade, do these steps Splitter Adjustment Miter Gauge Angle PointerTo set the angle pointer, do these steps To set the miter gauge pointer, do these steps Replacing V-Belts Adjusting FenceTo replace the V-belts, do these steps W1677 Wiring Diagram W1711 Wiring Diagram Motor & Electrical Troubleshooting Possible Cause Corrective Action Table Saw Operations Table/Body Breakdown Parts PART# Description Motor/Trunnion Breakdown Handwheellock Guard/Miter Gauge Breakdown XPB15 Warranty Page Page Comments Warranty Registration BOX BELLINGHAM, WA