Woodstock W1711, W1677 guide

OPERATIONS

W1677/W1711 10" Table Saw

Cutting rabbets with a standard saw blade DOES NOT

require the use of a sacrificial fence. Reduce motor over-

��

loading and blade wear by using a ripping blade. Ripping

��

blades are designed to clear the sawdust quickly.

To cut rabbets with the standard blade, do these steps:

��

1. DISCONNECT THE SAW FROM POWER!

2. Clearly mark the width of the rabbet cut on the

workpiece.

Note: Include marks on the edge of the workpiece

to clearly identify the intended cut while it is laying

flat on the saw table.

Figure 50. First cut when rabbet cutting

with a standard rip blade.

3.Raise the blade up to the desired depth of cut

(depth of rabbet channel desired). When cutting

deep rabbets, take more than one pass to reduce

��

the risk of kickback.

��

4. Adjust the fence so the blade is aligned with the

inside of your rabbet channel as shown in Figure 50.

5. Stand the workpiece on edge as shown in Figure 51,

and adjust the saw blade height to intersect with

��

the first cut.

6. Perform the second cut to complete the rabbet.

Figure 51. Second cut when rabbet cutting

with a standard rip blade.

-32-

Image 34

Woodstock W1711, W1677 owner manual To cut rabbets with the standard blade, do these steps

Contents

LEFT-TILT Table SAW Page Table of Contents Introduction Woodstock Technical Support W1677 Series Specifications W1711 Series Specifications Controls and Features Fence controls Blade Guard/Splitter Miter Gauge Safety Standard Safety Instructions Always Lock Mobile Bases if Used Before Operating Machinery Specific Safety Instructions for Table Saws Avoiding Potential Injuries Unplug saw before changing blades Use featherboards when possible To protect against kickback Kickback Use a zero-clearance table insert whenever possible Common Terms Extension Cords Electrical220V Operation Grounding Inventory SetupUnpacking Box Inventory Figures 12 Qty Standard Rails Figure Qty Shop Fox Classic Fence InventoryInventory Needed for Your Saw Long Rails Figure Qty Shop Fox Original Fence Inventory Flat Washers 3⁄ 8 Rail/Ext Table Machine Placement Cleaning Machine Mobile Base AssemblyTo assemble your table saw, do these steps Motor shipping brace Installing blade Adjusting table insert flush Before you test run the machine, do these steps Test RunTo test run the table saw, do these steps Blade Height OperationsGeneral Feed Rate Blade Material Blade SelectionBlade Types Changing Blades To change blades, do these steps Through Cuts Through vs. Non-Through CutsNon-Through Cuts Blade Tilt/Bevel Cuts When using the tilting mechanismRip Cuts To make a rip cut, do these steps Miter Cuts To crosscut using the miter gauge, do these stepsCross Cuts To cut a miter, do these steps Dado Cuts To use a stacked or wobble dado blade, do these steps First cut when making a dado With a standard ripping blade To cut dadoes with a standard blade, do these steps Rabbet Cuts To cut rabbets with the dado blade, do these steps To cut rabbets with the standard blade, do these steps Clearly mark the width of the rabbet cut on Workpiece Components Needed for the Resaw Barrier ResawingResaw Barrier To build the resaw barrier, do these steps Components Needed for the Auxiliary Fence Auxiliary FenceTo build the auxiliary fence, do these steps Components Needed for Resawing Resawing OperationsTo perform resawing operations, do these steps Aftermarket Safety Accessories Outfeed roller table Shop-Made Safety Accessories Here are some of the basic items you may want to consider Belts MaintenanceCleaning Table & Base Blade Tilt Stop Bolts ServiceTo set the stop bolts on the trunnion, do these steps To adjust the geared bearing housing, do these steps To adjust the trunnion assembly, do these stepsBlade Alignment Miter Slot Parallel to Blade Measuring blade to miter slot Shimming Wings To shim an extension wing, do these steps Splitter Adjustment To check and align the splitter to the blade, do these steps To set the angle pointer, do these steps Angle PointerMiter Gauge To set the miter gauge pointer, do these steps Replacing V-Belts Adjusting FenceTo replace the V-belts, do these steps W1677 Wiring Diagram W1711 Wiring Diagram Troubleshooting Motor & Electrical Table Saw Operations Possible Cause Corrective Action Parts Table/Body Breakdown PART# Description Motor/Trunnion Breakdown Handwheellock Guard/Miter Gauge Breakdown XPB15 Warranty Page Page Warranty Registration Comments BOX BELLINGHAM, WA