XPB15 | Woodstock W1677, W1711 specification

W1677/W1711 10" Table Saw

REF	PART�#	DESCRIPTION
57	XPB15	HEX�BOLT�5/16-18�X�3/8
57-1	XPW07	FLAT�WASHER�5/16
60	XPB07	HEX�BOLT�5/16-18�X�3/4
61	XPW07	FLAT�WASHER�5/16
62	X1677062	BRACKET
72	X1677072	SHAFT
73	X1677073	UPR�BLADE�GUARD�BRACKET
74	X1677074	LWR�BLADE�GUARD�BRACKET
140	XPB11	HEX�BOLT�5/16-18�X�1-1/2
141	XPW07	FLAT�WASHER�5/16
142	XPLW01	LOCK�WASHER�5/16
143	XPN02	HEX�NUT�5/16-18
144	XPB03	HEX�BOLT�5/16-18�X�1
145	XPSS02	SET�SCREW�5/16-18�X�3/8
200	X1677200	COMPLETE�MITER�GAUGE

REF	PART�#	DESCRIPTION
201	X1677201	MITER�GAUGE�BODY
201-1	X1677201-1	RIVET�2�X�4
201-2	X1677201-2	MITER�GAUGE�SCALE
202	X1677202	MITER�GAUGE�HANDLE
203	X1677203	STAR�KNOB�5/16-18�X�1-1/4
204	XPW07	FLAT�WASHER�5/16
205	X1677205	POINTER
206	XPFH04	FLAT�HD�SCR�1/4-20�X�5/8
207	X1677207	MITER�SLIDE�BAR
208	X1677208	SPECIAL�SCREW
209	X1677209	SPECIAL�WASHER
210	XPSS31	SET�SCREW�10-24�X�5/8
300	X1677300	BLADE�GUARD�ASSEMBLY
301	X1677301	BLADE�GUARD�LABEL

Safety labels warn about machine hazards and how to prevent machine damage or injury. The owner of this machine MUST maintain the original location and readability of all labels on this machine. If any label is removed or becomes unreadable, REPLACE that label before allowing the machine to enter service again. Contact Woodstock International, Inc. at (360) 734-3482 or www. shopfoxtools.com to order new labels.

PARTS

-55-

Image 57

Woodstock W1677, W1711 owner manual XPB15

Contents

LEFT-TILT Table SAW Page Table of Contents Woodstock Technical Support Introduction W1677 Series Specifications W1711 Series Specifications Fence controls Blade Guard/Splitter Miter Gauge Controls and Features Standard Safety Instructions Safety Always Lock Mobile Bases if Used Before Operating Machinery Specific Safety Instructions for Table Saws Unplug saw before changing blades Avoiding Potential Injuries Use featherboards when possible To protect against kickback Use a zero-clearance table insert whenever possible Kickback Common Terms 220V Operation ElectricalExtension Cords Grounding Unpacking SetupInventory Box Inventory Figures 12 Qty Inventory Needed for Your Saw Shop Fox Classic Fence InventoryStandard Rails Figure Qty Long Rails Figure Qty Flat Washers 3⁄ 8 Rail/Ext Table Shop Fox Original Fence Inventory Cleaning Machine Machine Placement Assembly Mobile BaseTo assemble your table saw, do these steps Motor shipping brace Installing blade Adjusting table insert flush Test Run Before you test run the machine, do these stepsTo test run the table saw, do these steps General OperationsBlade Height Feed Rate Blade Selection Blade MaterialBlade Types To change blades, do these steps Changing Blades Through vs. Non-Through Cuts Through CutsNon-Through Cuts Rip Cuts When using the tilting mechanismBlade Tilt/Bevel Cuts To make a rip cut, do these steps Cross Cuts To crosscut using the miter gauge, do these stepsMiter Cuts To cut a miter, do these steps To use a stacked or wobble dado blade, do these steps Dado Cuts To cut dadoes with a standard blade, do these steps First cut when making a dado With a standard ripping blade To cut rabbets with the dado blade, do these steps Rabbet Cuts Clearly mark the width of the rabbet cut on Workpiece To cut rabbets with the standard blade, do these steps Resaw Barrier ResawingComponents Needed for the Resaw Barrier To build the resaw barrier, do these steps Auxiliary Fence Components Needed for the Auxiliary FenceTo build the auxiliary fence, do these steps Resawing Operations Components Needed for ResawingTo perform resawing operations, do these steps Outfeed roller table Aftermarket Safety Accessories Here are some of the basic items you may want to consider Shop-Made Safety Accessories Cleaning MaintenanceBelts Table & Base Service Blade Tilt Stop BoltsTo set the stop bolts on the trunnion, do these steps To adjust the trunnion assembly, do these steps To adjust the geared bearing housing, do these stepsBlade Alignment Measuring blade to miter slot Miter Slot Parallel to Blade To shim an extension wing, do these steps Shimming Wings To check and align the splitter to the blade, do these steps Splitter Adjustment Miter Gauge Angle PointerTo set the angle pointer, do these steps To set the miter gauge pointer, do these steps Adjusting Fence Replacing V-BeltsTo replace the V-belts, do these steps W1677 Wiring Diagram W1711 Wiring Diagram Motor & Electrical Troubleshooting Possible Cause Corrective Action Table Saw Operations Table/Body Breakdown Parts PART# Description Motor/Trunnion Breakdown Handwheellock Guard/Miter Gauge Breakdown XPB15 Warranty Page Page Comments Warranty Registration BOX BELLINGHAM, WA