Manuals / Xantrex Technology / Computer Equipment / Computer Monitor

Xantrex Technology TM500A manual

Models: TM500A

1 44

Download 44 pages 16.27 Kb

Page 43

Image 43

Page 43

Image 43

Contents

TM500A Battery Status Monitor Installation Operator’s GuideDisclaimers About XantrexTrademarks Notice of Copyright1.0 INTRODUCTION Table of Contents2.0 INSTALLATION 3.0 CONFIGURATION7.0 SPECIFICATIONS Table of Contents5.0 TROUBLESHOOTING 6.0 SERVICE INFORMATIONIMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS BATTERY SAFETY INFORMATION14.2 1.0 INTRODUCTIONThe TM500A The TM500ATM48 48 Volt Unpacking and InspectionTM500A 12/24 Volt TM500A - NS 12/24 VoltMounting 2.0 INSTALLATIONPre-Installation Required Tools2.0 INSTALLATION Surface MountingWire Access Hole Trace Meter Bracket Trace Meter Surface Mounting the TM500A Using the AdaptorCommunication and Remote Cable Connections 2.0 INSTALLATION2.0 INSTALLATION Flush MountingCommunication and Remote Cable Connections Area To Be Cut-OutFlush Mounting the TM500A 2.0 INSTALLATIONExtended Length Ground Wire Extended Length Installations2.0 INSTALLATION 2.0 INSTALLATION Mounting/Wiring the ShuntDeltec Shunt Shunt Connections2.0 INSTALLATION Mounting Circuit Board to an Existing ShuntNOTE Use only the hardware supplied in the kit Shunt Circuit Board and Hardware2.0 INSTALLATION Connecting the Shunt BoardCircuit Diagram In-line FuseResetting to Factory Defaults 3.0 CONFIGURATIONSetup Restoring the Factory Defaults3.0 CONFIGURATION Setting ParametersSetting Parameters 14.43.0 CONFIGURATION Setting Parameters continued Charge Efficiency %Setting the Charge Efficiency Factor Setting Charger EfficiencySetting the Amp Hours Setting Parameters continued Amp Hours Ah3.0 CONFIGURATION Set Battery Amp-Hour Rating Ah LED Indicates Setting Parameters continuedSetting the Amp Hours 3.0 CONFIGURATION3.0 CONFIGURATION Setting Parameters continued CHARGED Indicator SetupStep A Setting the Fully-Charged Voltage Level Trigger on Voltage Only14.4 Setting Parameters continued CHARGED Indicator Setup continuedSetting the CHARGED Indicator Voltage Level Step B Switching OFF the Amperage DetectionStep A Setting the Fully-Charged Voltage Level Trigger on Voltage and Amperage3.0 CONFIGURATION Setting Parameters continued CHARGED Indicator Setup continuedSetting Parameters continued CHARGED Indicator Setup continued Step B Setting the Amperage Trigger LevelTrigger on Voltage and Amperage 3.0 CONFIGURATIONStep A Setting the Fully-Charged Voltage Level Trigger on Voltage and Time3.0 CONFIGURATION Setting Parameters continued CHARGED Indicator Setup continued3.0 CONFIGURATION Step B Setting the Time Duration1. H Trigger on Voltage and TimeThree-stage Chargers Charger ConsiderationsRelay Chargers Taper Chargers3.0 CONFIGURATION Setting Parameters continued Low-Voltage IndicatorConfiguring the Low-Voltage Alarm Low-Voltage Indicator4.0 OPERATION Indicators and ControlsRESET Button Front Panel Controls and IndicatorsAvailable Meters % state-of charge Indicators and Controls continued Basic MetersMeter Selection and LED Indicators 12.4Full Indicators and Controls continued Ah AMP HOURSPower Saving Mode Mode Indicator LEDsdSF Days Since Full Indicators and Controls continued Data MonitorsbHI High Battery Voltage bLO Low Battery VoltageTo access the Data Monitor Function Indicators and Controls continued4.0 OPERATION Meter Selection and LED Indicators Reminders and IndicatorsTo configure this function Amp-Hour ReminderTo configure this alarm Reminders and Indicators continued Low-Voltage Indicator4.0 OPERATION 4.0 OPERATION Reminders and Indicators continued CHARGED IndicatorTo reset the CHARGED LED Resetting the CHARGED IndicatorPossible Cause 5.0 TROUBLESHOOTINGSymptom Solution6.0 SERVICE INFORMATION Battery Amps 7.0 SPECIFICATIONSSpecifications Battery VoltsLimited Warranty 8.0 WARRANTYPage Arlington, WA Xantrex Technology Inc2001 Xantrex Technology Inc 5916 195th Northeast