Xantrex Technology XHR, XFR, XFR3 specification

Features and Specifications

Specifications

Table 1.3 Specifications for XFR 2800 W Series Supply with GPIB Interface Installed (7.5 V to 40 V)

Models	7.5-300	12-220	20-130	33-85	40-70
Program Resolution	1.16mV	1.8mV	3.08mV	5.1mV	6.2mV
Voltage	1.16mV	1.8mV	3.08mV	5.1mV	6.2mV
Current	42.0mA	30.8mA	18.2mA	13.0mA	9.8mA
OVP	1.16mV	1.8mV	3.08mV	5.1mV	6.2mV
Program Accuracy1
Voltage	10mV	50mV	75mV	75mV	75mV
Current	±0.12%	±0.12%	±0.12%	±0.3%	±0.3%
Current	900mA	750mA	500mA	425mA	350mA
	±0.1%	±0.1%	±0.1%	±0.1%	±0.1%
OVP	80mV	150mV	200mV	330mV	400mV
Readback Resolution
Voltage	1.16mV	1.8mV	3.08mV	5.1mV	6.2mV
Current	42.0mA	30.8mA	18.2mA	13.0mA	9.8mA
Readback Accuracy1
Voltage	30mV	60mV	75mV	75mV	75mV
	±0.12%	±0.12%	±0.12%	±0.3%	±0.3%
Current	900mA	750mA	500mA	425mA	350mA
	±0.1%	±0.1%	±0.1%	±0.1%	±0.1%

1.Apply accuracy specifications according to the following voltage program accuracy example: Set a model 20-130 power supply to 10 volts.

The expected result will be within the range of 10 volts ± 75mV ± 0.12% of the set voltage of 10 volts.

Release 3.1

15

Image 17

Xantrex Technology XHR, XFR, XFR3 manual Models 300 12-220 20-130 33-85 40-70

Contents

GPIB-XHR GPIB-XFR GPIB-XFR3 Page Operating Manual for Phone 604 422 Toll Free North America 800 667 Fax 604 421 How do you get service? What does this warranty not cover? Disclaimer Product Model Number Serial Number Purchased From Purchase Date Information About Your Power Supply Supply Safety Manual Revisions Main Sections About This Manual Contents Contents Description Features and Specifications Features and Specifications Features and FunctionsFunctions Readback OVP SpecificationsModels 140 12-100 20-60 35-35 40-30 Models 60-20 100-12 150-8 300-4 600-2 Models 300 12-220 20-130 33-85 40-70 Models 60-46 100-28 150-18 300-9 600-4 Models 130 20-50 33-33 40-25 60-18 Models 100-10 150-7 300-3.5 600-1.7 Initial Inspection Introduction Initial Inspection Installation and Configuration Gpib Interface Subplate Located on Power Supply Rear Panel Gpib Interface PCB PON SRQ Basic Setup ProcedureStep # Description Action Reference Address IEEE-488 Primary Address Selection Switch Position Power on results Power On Service Request PON SRQRear Panel SRQ Switch Position PON SRQ State Iset Condition Default Settings Model Example Ibfind devname Internal PCB Jumper Selections IEEE-488 Controller Connection High LOW OFF High OFF LOW User Signals J7 Connector User Signals J7 User Signal Connector Circuit Block Diagram J7 User Cable with Ferrite Block Gpib Operation Operation Example Ascii Request Service SRQ Set when Bit Decimal Description Reset By Position WeightPower On PON Set when unit LSB Format Command SyntaxComputer Entry Floating Number Definition Example Description Form Iset 2.0A Vset Command Summary AUXB? AUXA?CMODE? DLY? Cmode FAULT?Idata IHI Command Description Command ReferenceAuxa 1 on Auxb 1 on Changing an output setting Response Fold mode where mode is Mask None = Unmask ALL Snsp Status, and Fault Registers on SNSP, ALL, None Accumulated Status, Status, and Fault Registers on Response Vmax voltage Condition Mnemonic Bit Position Bit Weight Accumulated Status, Status, and Fault Registers 11 Error Codes Error Codes LEDs Troubleshooting Calibration Setup Voltage Mode CalibrationVoltage Program Calibration Procedure Readback Voltage Calibration Current Program Calibration Procedure Current Mode CalibrationCurrent Calibration Setup Current Readback Calibration Procedure Over Voltage Protection OVP Calibration Page Xantrex Technology Inc